Résumé du contenu de la page N° 1
Owner's Manual
®
6.75 HORSEPOWER
2450 PSi
2.0 GPM
Model No. 580.752310
o Safety
o Assembly
o Operation
o Maintenance
CAUTION: Before using this product,
° Parts
read this manual and follow al Safety
Rules and Operating instructions.
o Espat_ol
60179 U.S.A.
SEARS, ROEBUCK and CO., Hoffman Estates, IL
VBsit OUt Craftsman website: www.sears.comlcraftsman
0 8
Part No. 194646GS Draft 4 (09/28/2004)
Résumé du contenu de la page N° 2
WARRANTY .................................... 2 STORAGE .................................. 17-18 SAFETY RULES ............................... 2-4 TROUBLESHOOTING ............................ 19 KNOW YOUR PRESSURE WASHER ................ 5 REPLACEMENT PARTS ....................... 20-24 ASSEMBLY ................................... 6-8 NOTES ....................................... 25 OPERAT!ON ................................. 9-11 EM!SS!ON CONTROL WARRANTY .............. 26-27 SPECIFICATIONS ....
Résumé du contenu de la page N° 3
WARNING WARNtNG The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. , DANGER WHEN ADDING OR DRAINBNG FUEL Turn pressure washer OFF and let it cool at least 2 minutes before removing fuel cap. Loosen cap slowly to relieve pressure in tank. Fil! or drain fuel tank outdoors. DO NOT overfill tank. Allow space for fuel expansion. Keep fue! away from sparks, open flames, pilot lights, heat, and other ignit
Résumé du contenu de la page N° 4
WARNING WARNING Keep water spray away from electric wiring or fatal electric shock may result. Always wear eye protection when using equipment or when in vicinity of equipment in use. WARNING CAUTION DO NOT tamper with governed speed. DO NOT operate pressure washer above rated pressure. DO NOT touch hot surfaces. CAUTION Allow equipment to cool before touching. The pressure washer must be at least 5 feet from structures having combustible walls and/or other DO NOT secure spray gun in open positi
Résumé du contenu de la page N° 5
KNOW YOUR PRESSURE WASHER Read the owner's manual and safety rules before operating your pressure washer. Compare the illustrations with your pressure washer to familiarize yourself with the locations of various controls and adjustments. Save this manual for future reference. Model Data Decal Spray Gun Recoil Starter High Pressure Hose Nozzle Extension Oil Fill Cap and Dipstick Fuel Cap Water Inlet Adjustable Nozzle Throttle Control _. High Pressure Outlet Lever .___ Air Filter Detergent Pick-Up
Résumé du contenu de la page N° 6
Attach Handle Yourpressure washerrequires someassembly andis readyfor useonlyafterit hasbeenproperly serviced 1. Place handle assembly onto handle supports withtherecommended oil andfuel. connected to main unit. Make sure holes in handle Ifyou haveanyproblemswith theassemblyof align with holes on handle supports. your pressurewasher,pleasecall thepressure washerhelplineat 1=800=222=3136. Handle IMPORTANT: Anyattempt to runtheenginebeforeit hasbeenserviced withtherecommended oilwillresult in an e
Résumé du contenu de la page N° 7
Add Fuel Add Engine Oil IMPORTANT: Any attempt to crank or start the engine WARNING before it has been properly serviced with the recommended oil may result in an engine failure. NOTE: When adding oil to the engine crankcase, use only high quality detergent oil rated with API service classification SF, SG, SH, SJ or higher rated SAE 30 weight. DO NOT use special additives. WHEN ADDING FUEL 1. Choose a viscosity according to table below. Turn pressure washer OFF and let it cool at least 2 minutes
Résumé du contenu de la page N° 8
Connect Hose and Water Supply to Pump CAUTION IMPORTANT: To avoid pump damage, you must assemble the nozzle extension to the spray gun and attach all hoses before you start the engine. 1. Uncoil high pressure hose and attach one end of hose to base of spray gun. Tighten by hand. * Damage to equipment resulting from failure to follow this instruction will void warranty. 7. Turn ON water and squeeze trigger on spray gun to purge pump system of air and impurities. WARNING . Remove and discard shipp
Résumé du contenu de la page N° 9
To Start Your Pressure Washer HOW TO USE YOUR PRESSURE To start your engine-powered pressure washer for the WASHER first time, follow these instructions step-by-step. This if you have any problems operating your pressure starting information also applies whenever you start washer, please call the pressure washer helpline at the engine after you have let the pressure washer sit 1=800-222-3136. idle for at least a day. 1. Place pressure washer near an outside water Pressure Washer Location source
Résumé du contenu de la page N° 10
10.Movechokeleverto"Choke"position. NOTE:Forawarmengine, besurethechokeleveris inthe"Run"position. 11.Grasphandleandpullrecoilstarterlightlyuntilyou * DO NOT stop engine by moving choke lever to "Choke" feelsomeresistance, thenpullbriskly. position. 3. Squeeze trigger on spray gun to reWeve WARNING trapped pressure in hose to avo{d injury. NOTE: A small amount of water will squirt out when 3ressure is released. WARNING • When starting engine, pull cord slowly until resistance is felt and then pu
Résumé du contenu de la page N° 11
4. Slide adjustable nozzle forward to low pressure mode. Detergent cannot be applied with nozzle in high pressure position. 5. Make sure garden hose is connected to water inlet. Check that high pressure hose is connected to spray gun and pump. Start engine. 6. Apply detergent to a dry surface, starting from the bottom and working up. 7. Allow detergent to "soak in" for 3z5 minutes before rinsing. Reapply as needed to prevent surface . Twisting nozzle adjusts spray pattern from a from drying. nar
Résumé du contenu de la page N° 12
ENGINE TECHNICAL INFORMATION PRODUCT SPECIFICATIONS This is a single cylinder, L-head, air cooled engine, it Pressure Washer Specifications is a low emissions engine. Pressure .................. 2,450 PSI in the State of California, Model Series 120000 Flow Rate ................. 2.0 GPM engines are certified by the California Air Resources Chemical Mix............... Use as directed Board to meet emissions standards for 125 hours. Water Supply Temperature .... Not to exceed 100°F Such certifica
Résumé du contenu de la page N° 13
OWNER'S RESPONSiBiLiTiES Follow the hourly or calendar intervals, whichever occurs first. More frequent service is required when operating in adverse conditions noted below. MABNTENANCE SCHEDULE FILL tN DATES AS YOU SERVICE DATES COMPLETE REGULAR SERVICE SERVICE DATES Every 25 Every 50 Every 100 Before MAINTENANCE TASK Hours or Yearty Hours or Hours or Each Use Yearly Yeady Year y PRESSURE WASHER X _ Check/dean water inlet screen x Check high pressure hose x Check detergent hose x Check spray gu
Résumé du contenu de la page N° 14
. Place in-line filter screen into threaded end of Pressure washer parts should bekeptclean toreduce the nozzle extension. Direction does not matter. Push riskofoverheating andignition ofaccumulated debris. screen in with eraser end of pencil until it rests flat CAUTION at bottom of opening. Take care to not bend screen. . Place o-dng into recess. Push o-ring snugly against in-line filter screen. DO NOT insert any objects through cooling slots. 4. Assemble nozzle extension to spray gun, as descr
Résumé du contenu de la page N° 15
5. Usinga garden hose,remove additional debrisby 6. Set pressure washer in upright position. Add fuel backflushing waterthrough nozzleextension. Back and engine oil. flushbetween 30to60seconds. Turnadjustable ENGINE MAINTENANCE nozzleextension tostreamsprayandmovenozzle fromlowto highwhileflushing. WARNING 6. Reinstall orificeandin-line filterintonozzle extension. WHEN ADJUSTING OR MAKING REPAIRS TO YOUR PRESSURE WASHER DONOTovertighten orifice withallenwrench. 7. Reconnect nozzleextension to sp
Résumé du contenu de la page N° 16
Carburetor 6. Installoilfill pluganddipstick, tightensecurely. 7. Wipeupanyremaining oil. If you think your carburetor needs adjusting, see your nearest Sears service center. Engine performance 8. Reconnect sparkplugwiretosparkplug. may be affected at altitudes above 3000 feet. For Service Air Cleaner operation at higher elevations, contact your nearest Sears service center. Your engine will not run properly and may be damaged if you run it with a dirty air cleaner. Spark Attester Service Servic
Résumé du contenu de la page N° 17
AFTER EACH USE WINTER STORAGE Water should not remain in the unit for long periods of CAUTION time. Sediments or minerals can deposit on pump parts and "freeze" pump action. Follow these procedures after every use: • Failure to do so will permanently damage your pump 1. Flush detergent siphoning tube by placing the filter and render your unit inoperable. into a pail of clean water while running pressure • Freeze damage is not covered under warranty. washer in low pressure mode (adjustable nozzle
Résumé du contenu de la page N° 18
LONG TERM STORAGE Protect Pump To protect the pump use Sears pump saver to prevent if you do not plan to use the pressure washer for more freeze damage and lubricate pistons and seals. than 30 days, you must prepare the engine and pump for long term storage. CAUTION it is important to prevent gum deposits from forming in essential fuel system parts such as the carburetor, fuel filter, fuel hose or tank during storage. Also, * Failure to do so will permanently damage your pump and render your uni
Résumé du contenu de la page N° 19
Probmem Cause Correction 1. Nozzle in low pressure mode. 1. Pull nozzle backward for high pressure mode. 2. Water inlet is blocked. 2. Clear inlet. 3. Inadequate water supply. 3. Provide adequate water flow. Pump has following 4. Inlet hose is kinked or leaking. 4. Straighten inlet hose, patch leak. problems: failure to 5. Check and clean inlet hose strainer. 5. Clogged inlet hose strainer. produce pressure, erratic pressure, chattering, loss 6. Water supply is over 100°F. 6. Provide cooler wate
Résumé du contenu de la page N° 20
CRAFTSMAN 2450 PS_ Pressure Washer 580.752310 Main Unit m Exploded View and Parts List 12 4 4/-14 -
