Résumé du contenu de la page N° 1
NI PXI/PCI-5114 Specifications
8-Bit 250 MS/s Digitizer
Unless otherwise noted, the following conditions were used for each
specification:
• All filter settings
� All impedance selections
� Sample clock set to 250 MS/s
Typical values are representative of an average unit operating at room
temperature. Specifications are subject to change without notice. For the
most recent NI 5114 specifications, visit ni.com/manuals.
To access the NI 5114 documentation, including the NI High-Speed
Digitizer
Résumé du contenu de la page N° 2
Power .......................................................................................................14 Software...................................................................................................15 Environment ............................................................................................16 NI PXI-5114 .....................................................................................16 NI PCI-5114 ...........................................................
Résumé du contenu de la page N° 3
Specification Value Comments Voltage Levels Full Scale (FS) 50 Ω 1 MΩ — Input Range and Range Vertical Offset Range Vertical Offset Programmable (V ) Range (V) (V ) Range (V) pk-pk pk-pk Vertical Offset 0.04 ±0.8 0.04 ±0.8 0.1 ±0.8 0.1 ±0.8 0.2 ±0.8 0.2 ±0.8 0.4 ±0.8 0.4 ±0.8 1 ±6.5 1.0 ±8.0 2 ±6.0 2.0 ±8.0 4 ±5.0 4.0 ±8.0 10 ±30 10 ±2.0 20 ±25 40 ±15 Maximum Input 50 Ω 1 MΩ — Overload 7 V with |Peaks| ≤ 10 V |Peaks| ≤ 35 V rms Accuracy Resolution 8 bits — DC Accuracy NI PXI-5114: Within ±5 °
Résumé du contenu de la page N° 4
Specification Value Comments Bandwidth and Transient Response Bandwidth Range Rise/Fall Time, — (–3 dB) (V ) Bandwidth Typical pk-pk All ranges 125 MHz 2.8 ns except 0.04 0.04 100 MHz 3.5 ns Bandwidth — 20 MHz Noise Filter Limit Filter AC Coupling* *AC coupling Cutoff (–3 dB), 12 Hz available on Typical 1 MΩ only. Passband Referenced to Flatness 50 kHz. ±1 dB up to 50 MHz Bandwidth limit filter off. 1 0 –1 –2 –3 –4 Full Bandwidth –5 –6 Noise Filter –7 –8 –9 –10 1 M 10 M 100 M 200 M Frequenc
Résumé du contenu de la page N° 5
Specification Value Comments Spectral Characteristics Range (V ) 10 MHz, pk-pk –1 dBFS Spurious Free All ranges except 0.04 0.04 input signal. Dynamic Range with Harmonics Includes the –58 dBc –58 dBc nd (SFDR), Typical 2 through th the 5 Total Harmonic harmonics. Distortion –58 dBc –58 dBc Measured (THD), Typical from DC to Effective 125 MHz. Number of Bits 7.2 6.2 20 MHz (ENOB), bandwidth Calculated* limit filter off. Signal to Noise and Distortion 44 dB 38 dB (SINAD), Typica
Résumé du contenu de la page N° 6
Horizontal Sample Clock Specification Value Comments Sources Internal, Onboard Clock (internal VCXO)* * Internal Sample Clock is locked to the External, CLK IN (front panel SMB connector) Reference Clock or derived from the onboard VCXO. Onboard Clock (Internal VCXO) Sample Rate Real-Time Sampling Random Interleaved * Divide by n Range (Single Shot) Sampling (RIS) decimation used for all rates less than 3.815 kS/s to 250MS/s* 250 MS/s to 5 GS/s in 250 MS/s. For more increments of 25
Résumé du contenu de la page N° 7
Specification Value Comments External Sample Clock Sources CLK IN (front panel SMB connector) — Frequency 50 MHz to 250 MHz Divide by n Range decimation available where 1 ≤ n ≤ 65,535. For more information about Sample Clock and decimation, refer to the NI High-Speed Digitizers Help. Duty Cycle 45% to 55% — Tolerance Phase-Locked Loop (PLL) Reference Clock Specification Value Comments Sources NI PXI-5114 NI PCI-5114 — PXI_CLK10 (backplane RTSI 7 connector) CLK IN (front panel SMB CLK I
Résumé du contenu de la page N° 8
CLK IN (Sample Clock and Reference Clock Input, Front Panel Connector) Specification Value Comments Input Voltage Sine wave: 0.65 V to 2.8 V (0 dBm to 13 dBm) — pk-pk pk-pk Range Square wave: 0.2 V to 2.8 V pk-pk pk-pk Maximum Input 7 V with |Peaks| ≤ 10 V — rms Overload Impedance 50 Ω — Coupling AC — Trigger Reference (Stop) Trigger Specification Value Comments Trigger Types Types Sources Refer to the and Sources following Edge, Window, Hysteresis, CH 0, CH 1, TRIG, sections and to Video,
Résumé du contenu de la page N° 9
Specification Value Comments Analog Trigger (Edge, Window, and Hysteresis Trigger Types) Sources CH 0 (front panel BNC connector) — CH 1 (front panel BNC connector) TRIG (front panel BNC connector) Trigger Level 8 bits (1 in 256) Resolution CH 0, CH 1 TRIG (External Trigger) — Trigger Level 100% FS ±5 V Range Edge Trigger 5% FS up to 100 MHz 0.5 V up to 100 MHz pk-pk Sensitivity Level ±5% FS up to 10 MHz ±0.5 V up to 10 MHz Accuracy, Typical Jitter ≤ 65 ps rms — Trigger Filters Low Frequency (
Résumé du contenu de la page N° 10
Specification Value Comments Types Specific Line — Any Line Specific Field Standards SDTV: M-NTSC, B/G-PAL, SECAM, M-PAL fps = fields per second; EDTV: 480i/59.94 fps, 480i/60 fps, 480p/59.94 Fps, 480p/60 Fps, 576i/50 fps, 576p/50 Fps Fps = Frames per second HDTV: 720p/50 Fps, 720p/59.94 Fps, 720p/60 Fps, 1080i/50 fps, 1080i/59.94 fps, 1080i/60 fps, 1080p/24 Fps TRIG (External Trigger, Front Panel Connector) Specification Value Comments Connector BNC — Impedance 1 MΩ in parallel with 22 pF
Résumé du contenu de la page N° 11
Specification Value Comments As an Input (Trigger) Destinations Start Trigger (Acquisition Arm) — Reference (Stop) Trigger Arm Reference Advance Trigger Input Impedance 150 kΩ — V 2.0 V — IH V 0.8 V — IL Maximum Input –0.5 V to 5.5 V — Overload Maximum 25 MHz — Frequency As an Output (Event) Sources Start Trigger (Acquisition Arm) — Reference (Stop) Trigger End of Record Done (End of Acquisition) Probe Compensation (1 kHz, 50% duty cycle square wave, PFI 1 only) Output Impedance 50 Ω — Logic Ty
Résumé du contenu de la page N° 12
TClk Specifications National Instruments TClk synchronization method and the NI-TClk driver are used to align the sample clocks on any number of SMC-based modules in a chassis. For more information about TClk synchronization, refer to the NI-TClk Synchronization Help, which is located within the NI High-Speed Digitizers Help. � Specifications are valid for any number of modules installed in one NI PXI-1042 chassis. � All parameters set to identical values for each SMC-based module. � Sample
Résumé du contenu de la page N° 13
Waveform Specifications Specification Value Comments Onboard Memory 8 MB per Channel 8 megasamples — Size Standard per channel 64 MB per Channel 64 megasamples Option per channel 256 MB per Channel 256 megasamples Option per channel Minimum Record 1 Sample — Length Number of Zero up to full Record Length Single-record Pretrigger Samples mode and multiple-record mode. Number of Zero up to full Record Length Single-record Posttrigger Samples mode and multiple-record mode. Maximum Numb
Résumé du contenu de la page N° 14
Calibration Specification Value Comments Self-Calibration Self-calibration is done on software command. — The calibration corrects for gain, offset, compensated 1 MΩ attenuator, triggering, and timing adjustment errors for all input ranges. External Calibration The external calibration calibrates the VCXO, gain, — (Factory Calibration) and the voltage reference. Appropriate constants are stored in nonvolatile memory. Interval for External 2 years — Calibration Warm-Up Time 15 minutes — Power
Résumé du contenu de la page N° 15
Software Specification Value Comments Driver Software NI PXI-5114: NI-SCOPE 2.9 or later. — NI PCI-5114: NI-SCOPE 3.1 or later. NI-SCOPE is an IVI-compliant driver that allows you to configure, control, and calibrate the NI 5114. NI-SCOPE provides application programming interfaces for many development environments. Application NI-SCOPE provides programming interfaces, — Software documentation, and examples for the following application development environments: �LabVIEW ™ ™ � LabWindows /CV
Résumé du contenu de la page N° 16
Environment NI PXI-5114 Note To ensure that the NI PXI-5114 cools effectively, follow the guidelines in the Maintain Forced Air Cooling Note to Users included in the NI PXI-5114 kit. The NI PXI-5114 is intended for indoor use only. Specification Value Comments Operating 0 ºC to +55 ºC in all NI PXI chassis except the following: — Temperature 0 ºC to +45 ºC when installed in an NI PXI-1000/B or PXI-101x chassis. Meets IEC-60068-2-1 and IEC-60068-2-2. Storage – 40 ºC to +71 ºC. Meets IEC-60068
Résumé du contenu de la page N° 17
NI PCI-5114 Note To ensure that the NI PCI-5114 cools effectively, follow the guidelines in the Maintain Forced Air Cooling Note to Users included in the NI PCI-5114 kit. Also, to maximize airflow and extend the life of the device, leave any adjacent PCI slots empty. The NI PCI-5114 is intended for indoor use only. Specification Value Comments Operating 0 ºC to +45 ºC. Meets IEC-60068-2-1 and IEC-60068-2-2. — Temperature Storage – 40 ºC to +71 ºC. Meets IEC-60068-2-1 and — Temperature IEC-600
Résumé du contenu de la page N° 18
Safety, Electromagnetic Compatibility, and CE Compliance Specification Value Comments Safety The NI 5114 meets the requirements of the following — standards of safety for electrical equipment for measurement, control, and laboratory use: � IEC 61010-1, EN 61010-1 � UL 61010-1, CAN/CSA-C22.2 No. 61010-1 For UL and other safety certifications, refer to the product label or visit ni.com/certification, search by model number or product line, and click the appropriate link in the Certification col
Résumé du contenu de la page N° 19
Physical Specification Value Comments Dimensions NI PXI-5114 NI PCI-5114 — 3U, One slot, 35.5 × 2.0 × 11.3 cm PXI/cPCI Module (13.4 × 0.8 × 4.4 in.) 21.6 × 2.0 × 13.0 cm (8.5 × 0.8 × 5.1 in.) Weight 455 g (16 oz) 421 g (14.8 oz) — Front Panel Connectors Label Function Connector Type — CH 0 Analog Input BNC female CH 1 Analog Input BNC female TRIG External Trigger BNC female CLK IN Sample Clock Input and SMB jack Reference Clock Input AUX I/O PFI 0, PFI 1 9-pin mini-circular DIN NI PXI-5114 F
Résumé du contenu de la page N° 20
Where to Go for Support The National Instruments Web site is your complete resource for technical support. At ni.com/support you have access to everything from troubleshooting and application development self-help resources to email and phone assistance from NI Application Engineers. A Declaration of Conformity (DoC) is our claim of compliance with the Council of the European Communities using the manufacturer’s declaration of conformity. This system affords the user protection for electro
