ページ1に含まれる内容の要旨
Dual Mode CMOS Internet Camera
ICA-151
Version 1.1
Quick Installation Guide
ページ2に含まれる内容の要旨
Table of Contents 1. PACKAGE CONTENTS ................................................................................... 3 2. SYSTEM REQUIREMENTS .............................................................................. 4 3. OUTLOOK ................................................................................................ 5 3.1 Front Panel ......................................................................................... 5 3.2 Rear Panel ....................................
ページ3に含まれる内容の要旨
1. PACKAGE CONTENTS ó 1 x ICA-151 ó 1 x Camera Stand ó 1 x Power Adapter ó 1 x CD-ROM ó 1 x Quick Installation Guide Please use the power adapter in this package. Using a power supply with a different voltage rating will damage and void the warranty for this product. Note
ページ4に含まれる内容の要旨
2. SYSTEM REQUIREMENTS Network Interface 10/100 Base-TX Ethernet Monitoring System Recommended for Internet Explorer 6.0 or later • CPU: Pentium 4, 1.5GHz or above • Memory Size : 512 MB or above • VGA card resolution : 1024 x 768 or above • Network bandwidth: In VGA resolution mode, System Hardware minimum upload bandwidth is 1Mbps. Optional: • Sound Card • Microphone (for PC) • Speaker (for PC and ICA-151)
ページ5に含まれる内容の要旨
3. OUTLOOK 3.1 Front Panel Microphone ACT PWR LAN LED Status LED Description Off No power. PWR On Power on. Blinking The Power LED will blink during start up (15 ~ 20 sec). Off Camera is not capturing video. ACT Blinking Camera is capturing video. Off LAN is not connected or camera is not sending/receiving data. LAN Blinking Data is being transmitted or received via the LAN connection.
ページ6に含まれる内容の要旨
3.2 Rear Panel PWR LAN AUDIO OUT PORT PORT Description AUDIO OUT An external speaker can be plugged in. PWR Connect the supplied power adapter. LAN Connect your Camera to a 10/100Base-TX hub or switch. Reset to manufacturer default valued and reboot. When pressed and held over 10 seconds, the settings of IP Camera will be set to the default values. Upon completion, the PWE LED will blink three times. Reset Bottom Panel of ICA-151
ページ7に含まれる内容の要旨
4. Physical Installation 1. Connect an Ethernet cable Connect one end of an Ethernet cable to the LAN port located on the IP camera’s rear panel and connect the other end to the network device (hub or switch). 2. Attach the external power supply Attach the provided power adapter to the IP camera’s connector labeled “PWR” on the rear panel. 3. Check the LEDs a. The Power LED will turn on briefly, and then start blinking during startup. After startup is completed, the Power LED will remain ON
ページ8に含まれる内容の要旨
5. Setup Wizard Configuration Initial setup should be performed by using the supplied Windows-based Setup Wizard as follows: 1. Insert the bundled Product CD disk into CD-ROM drive to launch the autorun program. 2. After the web page displayed, click the “Setup Wizard” hyperlink on the list to start the configuration process. If the web page does not appear, click “Start” on the task bar and select “Run” to type “X:\Utility\SetupWizard\SetupWizard. exe”, assume X is your CD-Rom drive. Note 3
ページ9に含まれる内容の要旨
4. After clicking the setup camera button, it will auto search for the IP Cameras on your network. Click on to continue. 5. The next screen below will list the IP Camera on your network. Select it from the list on the left side, the current settings table will be displayed on the right side. Click on to continue.
ページ10に含まれる内容の要旨
6. The administrator login window will pop up. If the Administrator Name and Administrator Password have been set, you will be prompted to enter them. If using the default values, please enter “admin” for both the name and the pass- word. Click on “OK” to continue. 7. On the following Camera Settings screen, you can fill and configure the Device Name, Description, Time Zone, Local Date and time here. Click on to continue. 10
ページ11に含まれる内容の要旨
8. You can choose “Fixed IP Address” or “Dynamic IP Address” here. Click on to continue. 1. Fixed IP Address is recommended, and can always be used. 2. Dynamic IP Address can only be used if your LAN has a DCHP Server. Note 9. If you chose to use Fixed IP Address, the following TCP/IP Settings screen will be displayed. You can configure the IP Address, Subnet Mask, Default Gateway, Primary and secondary DNS. Click on to continue. 11
ページ12に含まれる内容の要旨
10. The next screen below will display all details of the IP Camera. Click on to continue if those settings are correct, or click on back to modify any incor- rect values. 11. In this confirmation window below, click on “OK” to confirm that you want to save the new settings. If you want to cancel your changes, please click on “Cancel”. 12
ページ13に含まれる内容の要旨
12. After confirming, the wizard will start to save the new settings as below screen. 13. When the saving process is completed, the prompt window will be displayed as below screen. Click on “OK” to finish. 1
ページ14に含まれる内容の要旨
14. The setup wizard now is completed. Click on “Exit” to close the setup wizard. After modifications, you may now connect the IP camera with the new configuration via web browser. 1
ページ15に含まれる内容の要旨
6. Cam Viewer Lite Installation The Cam Viewer Lite / Pro 30 days trial version installation steps are similar. Below is the installation of Cam Viewer Lite. Note 1. Insert the bundled Cam Viewer CD disk into the CD-ROM drive to launch the autorun program. Once completed, a welcome menu screen will appear. Click the “Cam Viewer Lite” hyperlink, the below InstallShield Wizard dialog box will appear. If the welcome screen does not appear, click “Start” at the taskbar. Then, select “Run” and t
ページ16に含まれる内容の要旨
3. The “Welcome to the InstallShield Wizard for Planet Cam Viewer Lite 1.0.3” will display on the screen, please click “Next”. 4. Please read the license agreement and then check “I accept the terms of the license agreement” if you are agreed and click “Next” to continue the installation 1
ページ17に含まれる内容の要旨
5. Please key in user name and company name for which you want and click “Next” to continue installation. 6. Check the option “Complete”, all program features will be installed (Requires the most disk space) and click “Next” to continue installation. 1
ページ18に含まれる内容の要旨
7. “Ready to Install the Program” will appear to prompt you to start the installation. Please click “Install” to start. 8. Please click “No” to finish the Cam Viewer Lite installation. In above step, when Cam Viewer works with MBM5 (Motherboard Monitor 5), Cam Viewer will display CPU temperature and fan speed. Please click “Yes” if you need this function and refer to the Note manual of Cam Viewer CD disk for complete installation. 1
ページ19に含まれる内容の要旨
Appendix A: Feature Listing for Cam Viewer Software Version Cam Viewer Lite Cam Viewer Pro IP Camera Input 32 4 / 8 / 16 / 32 / 64 - V Dual Monitor - V Smart Guard I/O Device V V Hotline - V - V Address Book Unusual event Unusual event Log Viewer System log System log Counting application - 2 way counting Counting Application - Unlimited Remote Playback Server 1 Channel 16 Channels Concurrent Playback Counting Function - V General Motion Missing Object General Motion Foreign Object Smart Search
ページ20に含まれる内容の要旨
Appendix B: Suggest Hardware / System Requirement Total FPS ~600 600~480 480~240 240~120 120~ Intel Core Intel Core Intel Intel P4 Intel P4 2 Duo 2 Duo Pentium CPU 3.0 2.8 QX6800 E6600 D 930 RAM 4 GB 2 GB 2 GB 1 GB 1 GB Chipset of Intel 946 or 965 chip, Intel Chipset recommended Motherboard ATI Radeon 9200, nVIDIA GeForce FX-5200, VGA Card Intel 945/965 or above (ATI recommended) Ethernet 100Base-TX or Above, Gigabit LAN recommended 160 GB or above Hard Disk Windows 2000 / XP / 2003 O.S. Tot
