ページ1に含まれる内容の要旨
EN
User manual 2
Dishwasher
ZDS 2010
ページ2に含まれる内容の要旨
Contents Safety information _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 2 Setting and starting a washing programme _ _ _ _ 10 Control panel _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 3 Care and cleaning _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 11 Washing programmes _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 4 What to do if… _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 12 Use of the appliance _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 5 Technical data _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 13 Setting the water softener _ _ _ _ _ _ _ _ _ _ _ _ _ 5 Envir
ページ3に含まれる内容の要旨
• Do not change the specifications or modify this prod- Contact your local Service Force Centre. uct. Risk of injury and damage to the appliance. • Do not drill into the sides of the appliance to prevent • Do not use the appliance: damage to hydraulic and electrical components. – if the mains cable or water hoses are damaged, Warning! Carefully obey the instructions for – if the control panel, worktop or plinth area are dam- electrical and water connections. aged, that you can get access to the
ページ4に含まれる内容の要旨
– The on/off indicator light goes off (position OFF). Programme knob and on/off indicator light • To set a washing programme, turn the programme Delay start button knob clockwise or anticlockwise. The programme Use the delay start button to delay the start of the washing marker on the programme knob must agree with one programme with an interval of 3 hours. Refer to the chapter of the washing programmes on the control panel. 'Setting and starting a washing programme'. – The on/off indicator ligh
ページ5に含まれる内容の要旨
Programme Duration (in minutes) Energy (in kWh) Water (in litres) Quick 65° A 30' 30 0,8 8 Economy 50° 120 - 130 0,8 - 0,9 12 - 13 Prewash 11 0,1 5 The pressure and temperature of the water, the var- iations of power supply and the quantity of dishes can change these values. Use of the appliance Refer to the following instructions for each step of pro- 5. Set the correct washing programme for the type of cedure: load and soil. 1. Make a check if the water softener level is correct for 6. Fill th
ページ6に含まれる内容の要旨
Water hardness Water hardness setting °dH °TH mmol/l Clarke manually electronically 51 - 70 91 - 125 9,1 - 12,5 64 - 88 2 10 43 - 50 76 - 90 7,6 - 9,0 53 - 63 2 9 37 - 42 65 - 75 6,5 - 7,5 46 - 52 2 8 29 - 36 51 - 64 5,1 - 6,4 36 - 45 2 7 23 - 28 40 - 50 4,0 - 5,0 28 - 35 2 6 19 - 22 33 - 39 3,3 - 3,9 23 - 27 2 5 15 - 18 26 - 32 2,6 - 3,2 18 - 22 1 4 11 - 14 19 - 25 1,9 - 2,5 13 - 17 1 3 4 - 10 7 - 18 0,7 - 1,8 5 - 12 1 2 1) 1) < 4 < 7 < 0,7 < 5 1 1 1) No use of salt required. 1. Press and hold
ページ7に含まれる内容の要旨
1 2 5 6 It is normal that water overflows from the salt con- tainer when you fill it with salt. Make sure that there is no grain of salt outer of the salt compartment. Salt which stays on the tank for a while drills the tank. It is recommended to start a wash- ing programme immediately after you fill the salt con- tainer. This prevents of corrosion because of spilled salt. 3 4 When you set electronically the water softener to level 1, Fill the salt container with the salt indicator light does no
ページ8に含まれる内容の要旨
Adjusting the dosage of rinse aid Caution! Do not fill the rinse aid dispenser with other products (e.g. dishwasher cleaning agent, The rinse aid dial is set at liquid detergent). There is a risk of damage to the the factory at position 4. appliance. To increase or decrease the dosage refer to 'What to do if...' Loading cutlery and dishes Helpful hints and tips Caution! Only use the appliance for household utensils that are applicable for dishwashers. Do not use the appliance to clean objects
ページ9に含まれる内容の要旨
1 2 1 2 Arrange the items to let For longer items, fold the water touch all surfaces. cup racks up. Do these steps to move the upper basket to the upper or lower position: Adjustment of the height of the upper basket 1. Move the front runner stops (A) out. If you put large plates in the lower basket, first move the 2. Pull the basket out. upper basket to a upper position. 3. Put the basket in the upper or lower position. Warning! Adjust the height before you load the 4. Replace the front runner
ページ10に含まれる内容の要旨
tainers. In this condition the rinse aid indicator light stays on when the appliance is switched on. 1. Do a check if these tablets are applicable for the local water hardness. Refer to the instructions from the manufacturer. 2. Select the lowest setting for the water hardness and rinse aid dosage. Do these steps if the drying results are not satisfactory 5 6 1. Fill the rinse aid dispenser with rinse aid. 2. Set the rinse aid dosage to position 2. Different brands of detergent dissolve in diffe
ページ11に含まれる内容の要旨
• The appliance stops automatically. Do not open the door during the countdown to pre- vent interruption of the countdown. When you close • The end indicator light comes on. the door again, the countdown continues from the point For better drying results, keep the door ajar for some mi- of interruption. nutes before you remove the dishes. Let the dishes cool down before you remove them from Cancelling a delay start: the appliance. Hot dishes are easily damaged. 1. Press and hold the start/cancel
ページ12に含まれる内容の要旨
External cleaning If not possible, empty the appliance and close the door. Clean the external surfaces of the appliance and control Disconnect the water inlet hose and remove water from panel with a damp soft cloth. Only use neutral detergents. the water inlet hose. Do not use abrasive products, scouring pads or solvents (acetone, trichloroethylene etc...). Frost precautions Caution! Do not install the appliance where the temperature is below 0 °C. The manufacturer is not responsible for damage
ページ13に含まれる内容の要旨
Fault code and malfunction Possible cause and solution The programme does not start • The appliance door is not closed. Close the door. • Mains plug is not connected in. Put in the mains. • The fuse has blown out in the household fuse box. Replace the fuse. • Delay start is set. Cancel the delay start to start the programme immediately. After the check, switch on the appliance. The programme • Product number (PNC) continues from the point of interruption. If the malfunction • Serial number (S.N.
ページ14に含まれる内容の要旨
Depth cm 60,5 Electrical connection - Voltage - Information on the electrical connection is given on the rating plate on the Overall power - Fuse inner edge of the dishwasher door. Water supply pressure Minimum 0,5 bar (0,05 MPa) Maximum 8 bar (0,8 MPa) Capacity Place settings 9 Environment concerns markings, e.g. >PE<, >PS<, etc. Discard the packaging The symbol on the product or on its packaging materials in the applicable container at the community indicates that this product may not be
ページ15に含まれる内容の要旨
Install the appliance worktop to the appliance if you want to use the dishwasher as a freestanding appliance. The plinth on freestanding appliance is not adjustable. Adjusting the level of the appliance Make sure that the appliance is level to close and seal the door correctly. If the level of the appliance is correct, the door does not catch on the sides of the cabinet. If the door does not close correctly, loosen or tighten the adjustable 3 4 feet until the appliance is level. Water connection
ページ16に含まれる内容の要旨
Electrical connection Warning! The manufacturer is not responsible if Make sure that the mains plug is accessible after you do not follow these safety precautions. installation. Ground the appliance according to safety precautions. Do not pull the mains cable to disconnect the appliance. Make sure that the rated voltage and type of power on the Always pull the mains plug. rating plate agree with the voltage and the power of the Warning! The appliance is supplied with a 13 amp local power suppl
ページ17に含まれる内容の要旨
17
ページ18に含まれる内容の要旨
18
ページ19に含まれる内容の要旨
19
ページ20に含まれる内容の要旨
To buy accessories, consumables and spare parts at our online shop please visit: www.zanussi.co.uk www.zanussi.com 117952390 - 00 - 062009
