ページ1に含まれる内容の要旨
WDR-516S
Installation Guide
ページ2に含まれる内容の要旨
FCC Compliance Statement Caution : Any changes or modifications in construction of this device which are not expressly approved the party responsible for compliance could void the user's authority to operate the equipment. NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
ページ3に含まれる内容の要旨
Important Notice 1. Do not place heavy objects on the top of the WDR-516S. 2. WDR-516S is not weatherproof. In case of outdoor use, equip a weatherproof case to protect WDR- 516S from water, moisture, or temperature (higher or lower than specifications). To clean the WDR-516S, gently wipe the outside with a clean dry cloth. 3. Be sure to use a DC adapter that is provided by DENTEC Corp. Connecting WDR-516S directly to an AC current will cause electric damages to WDR-516S. 4.
ページ4に含まれる内容の要旨
OVERVIEW.................................................................................................................................. 7 1. What is WDR-516S?............................................................................................................ 7 2. Supplied Accessories......................................................................................................... 8 3. Description & Function ...............................................................
ページ5に含まれる内容の要旨
8.2.2. Daylight Saving..................................................................................................... 22 8.2.3. Time Format ......................................................................................................... 23 8.2.4. Date...................................................................................................................... 23 8.2.5. Time.............................................................................................
ページ6に含まれる内容の要旨
14.3. Available HDD.......................................................................................................... 36 14.4. Registering & Formatting HDD................................................................................. 37 15. Network Monitoring & Managing ................................................................................. 38 15.1. Connecting Ethernet ................................................................................................ 38
ページ7に含まれる内容の要旨
OVERVIEW 1. What is WDR-516S? The WDR-516S is a 4-Analog, 12-IP channel network digital video recorder. The WDR-516S can record and display 4 analog video channels and 12 IP video channels simultaneously. Video, Audio, and Text Event-Logs are digitized and stored on two internal hard-drives. Key features □ Expandable up to 16 channels (4 analog video channels + 12 IP video channels) □ 1 channel audio recording & playback □ Total 120 ips recording speed (Analogue video 60ips +
ページ8に含まれる内容の要旨
2. Supplied Accessories Unpack and check all the items as below. 1. WDR-516S (1) 2. DC Power Supply (1) (110V~220V) 3. AC Power Cord (1) 4. CD-ROM (Including WDR Manager) (1) 5. Remote Controller (1) 6. Guide (2) 7. Plug Bracket (1) 8. HDD Fixing Screw (8) 8 WDR-516S Installation Guide Rev 1.0(93/11)
ページ9に含まれる内容の要旨
3. Description & Function WDR-516S Front 1 3 6 4 2 5 (1) LED (2) IEEE1394 connecter (3) Remote controller receiver (4) USB connecter (5) Function buttons (6) Bracket fixing hole for rack mount 9 WDR-516S Installation Guide Rev 1.0(93/11)
ページ10に含まれる内容の要旨
WDR-516S Rear 10 11 9 7 8 12 13 14 19 15 18 20 17 16 (7) Power switch (8) Ethernet connector (9) BNC connector for Video input (10) Audio input / output connector (11) RS232 connecter (9Pin D-Sub) (12) Terminal block for RS232 & 422/485 (13) Terminal block for Sensor input (14) Terminal block for Relay output (15) Video output for MONITOR or VCR (16) Video input type/impedance select & remote controller switch (17) IEEE1394 connecter (18) USB connecter (19) Power
ページ11に含まれる内容の要旨
INSTALLATION AND CONNECTION 4. Connecting & Running WDR-516S 4.1. Connecting camera (1) Connect CCTV camera to WDR-516S with BNC cable as shown below. (2) Set video type (NTSC/PAL) by rear panel’s switch. The video type for all channels should be either NTSC or PAL. NTSC is the standard used in North America. (3) Set the impedance control switch for each channel as needed. It may be necessary to configure impedance of video input differently f
ページ12に含まれる内容の要旨
4.2. Connecting Monitor (1) Connect CCTV monitor to WDR-516S with BNC cable as shown below. WDR-516S has two video output ports ; for Monitor and VCR. The output signals from the two ports are same and either port may be used. 4.3. Connecting Audio (1) Connect audio signal to WDR-516S. 12 WDR-516S Installation Guide Rev 1.0(93/11)
ページ13に含まれる内容の要旨
4.4. Supplying Power (1) Connect power cable to WDR-516S. (2) Turn on the power switch located on the WDR-516S rear panel. Use the plug bracket to secure the power cable if needed. To connect EARTH, refer to the following picture. 13 WDR-516S Installation Guide Rev 1.0(93/11)
ページ14に含まれる内容の要旨
5. Running OSD menu 5.1. Using menu Press the [MENU] button to open the OSD Configuration Menu. (1) Main Menu (2) Sub-menu (3) Setting Page (4) Help message (1) Main Menu Tabs: The selected tab is shown in blue and the related sub-menus will be shown below the tab. To move to the previous/next Main Menu Tab, use the [ ◄ or ►] arrow buttons. To move to a sub-menu, press the [ENTER] or [▼] buttons. (2) Sub-menu: The selected sub-menu is shown in blue and the related set
ページ15に含まれる内容の要旨
5.2. Dialogue Box to Edit a Word There are two methods to set word. (1) Using number button Enter the related numbers in order of horizontal/vertical. (For example, in order to select “ C ” , press [3] and [2] buttons.) (2) Using arrow button Select a value using the [ ◄ or ►] or [▲/▼] buttons. The intersection of the horizontal and vertical bar is selected value. Press the [ ►] button to confirm the selected value. (3) Function word The following symbols are for executin
ページ16に含まれる内容の要旨
6. Setting remote controller 6.1. Setting remote control DIP switch Set the remote control DIP switch to “ON.” REMOTE CONTROL N ON Hi-Z 1 2 3 4P OFF 6.2. Set ID of WDR-516S When controlling several WDR-516S with one remote controller, set Remote Control ID as follows. (1) Press [MENU] button. (2) Select “System” with using [ ►] button and press the [ENETR] or [▼] button. 16 WDR-516S Installation Guide Rev 1.0(93/11)
ページ17に含まれる内容の要旨
(3) Select “Miscellaneous” from the sub-menu list using the [▼] button and press the [ENETR] button. (4) Select “Remote Control ID,” and press the [ENETR] button. (5) Select a value using the [ ◄ or ►] buttons and press the [EXIT] button. (6) Press the [EXIT] button to exit the Settings Page and return to Monitor mode. Remote Control ID Up to 16 WDRs can be controlled with a single remote controller. 6.3. Selecting WDR-516S If several WDRs are set with unique
ページ18に含まれる内容の要旨
6.4. Operable range of remote controller WDR 6.5. Loading the batteries into remote controller Remote controller requires two AAA-type batteries. 2. Taking care that the poles(+/-) 1. Remove the battery cover. 3. Replace the battery cover. are correctly positioned. 18 WDR-516S Installation Guide Rev 1.0(93/11)
ページ19に含まれる内容の要旨
7. WDR-516S Configuration 7.1. Basic Configuration 7.2. Advanced Configuration 19 WDR-516S Installation Guide Rev 1.0(93/11)
ページ20に含まれる内容の要旨
7.3. External Storage & Backup Configuration 7.4. Internet/Intranet Configuration WDR 20 WDR-516S Installation Guide Rev 1.0(93/11)
