ページ1に含まれる内容の要旨
INSTALLATION INSTRUCTIONS FOR PART 99-5721
APPLICATIONS
2010 FORD TAURUS
(NON-NAV)
99-5721
KIT FEATURES
• DIN Head unit provisions with pocket
• ISO DIN Head unit provision with pocket
• DDIN Head unit provisions
• ISO Stacked head unit provisions
• Painted Silver to match factory fi nish
KIT COMPONENTS
• A) Radio Housing/Climate Control • B) (2) A/C Vent Trim Panels • C) ISO Brackets • D) ISO Trim Plate
• E) DDIN Brackets • F) DDIN Trim Plate • G) (10) #8x3/8” Phillips Screws • H) Pocke
ページ2に含まれる内容の要旨
TABLE OF CONTENTS DASH DISASSEMBLY • 2010 FORD TAURUS . . . . . . . . . . . . . . . . . . . . . . 1-3 KIT PREPARATION • 2010 FORD TAURUS . . . . . . . . . . . . . . . . . . . . . . . . 4 KIT ASSEMBLY 2010 FORD TAURUS • DIN HEAD UNIT PROVISION . . . . . . . . . . . . . . . . . . . 5 • ISO DIN HEAD UNIT PROVISION . . . . . . . . . . . . . . . 6 • DDIN / STACKED ISO DIN HEAD UNIT PROVISION . . 7 CUSTOMIZING THE DISPLAY • 2010 FORD TAURUS . . . . . . . . . . . . . . . . . . . . . .
ページ3に含まれる内容の要旨
99-5721 DASH DISASSEMBLY 2010 FORD TAURUS Disconnect the negative battery 1 A terminal to prevent an accidental short circuit. 2 Unclip and remove the (2) trim panels on the left and right side of the cup holders and shifter. (Fig. A) 3 Unclip and remove the trim panel to B the right of the passenger a/c vent. (Fig. B) 4 Unclip and remove the knee bolster panel below the steering column. (Fig. B) C Remove (1) 9/32” screw from the 5 trim panel to the left of the steering column that has t
ページ4に含まれる内容の要旨
99-5721 DASH DISASSEMBLY 2010 FORD TAURUS Unclip and remove the gauge cluster 7 D trim panel. (Fig. D) 8 Unclip and remove the trim panel/ speaker grill from above the radio trim panel. (Fig. D) Remove (4) Phillips screws from the 9 cup holder trim panel then unclip E and remove the panel. (Fig. E) Remove (4) Phillips screws from 10 the shifter trim panel then slide it backwards. Note: There is no need to remove this panel completely. F (Fig. F) Continued on Pg. 3 .......................
ページ5に含まれる内容の要旨
99-5721 DASH DISASSEMBLY 2010 FORD TAURUS 11 Remove (4) Phillips screws from the G ash tray trim panel then unclip and remove the ash tray assembly. (Fig. G) 12 Remove (10) phillips screws from the radio trim panel including the a/c vents then unclip and remove the panel. (Fig. H) H 13 Remove (4) Phillips screws securing the radio display. (Fig. I) Remove (4) Phillips screws securing 14 the radio. (Fig. I) Unclip and remove the a/c vents I 15 and chrome vent trim from the factory pane
ページ6に含まれる内容の要旨
99-5721 KIT PREPARATION 2010 FORD TAURUS Attach the left and right a/c vent trim 1 A panels to the main radio housing panel using the provided (10) #8X3/8” Phillips screws. (Fig. A) 2 Snap the a/c vents and chrome vent trim into the appropriate vent trim panel. Note: The vents are labeled L and R on the tops. Continue to kit assembly............... 4
ページ7に含まれる内容の要旨
99-5721 KIT ASSEMBLY DIN HEAD UNIT PROVISION Slide the DIN cage into the Radio 1 A Housing and secure by bending the metal locking tabs down. (Fig. A) 2 Snap the pocket into the bottom opening of the radio housing. (Fig. B) 3 Slide the aftermarket head unit into the cage and secure. (Fig. C) B 4 Locate the factory wiring harness and antenna plug in the dash. Metra recommends using the proper mating adapters from Metra and/or AXXESS. C Plug the jumper harness into the car 5 side of t
ページ8に含まれる内容の要旨
99-5721 KIT ASSEMBLY ISO DIN HEAD UNIT PROVISION Mount the ISO Brackets to the head 1 A unit with the screws supplied with the unit. (Fig. A) 2 Snap the pocket into the bottom opening of the radio housing. (Fig. B) 3 Slide the head unit into the radio opening until the side clips engage. (Fig. C) B 4 Snap the Trim plate into the Radio Housing. (Fig. C) Locate the factory wiring harness 5 and antenna plug in the dash. Metra recommends using the proper mating adapters from Metra and/or
ページ9に含まれる内容の要旨
99-5721 KIT ASSEMBLY DDIN / STACKED ISO DIN HEAD UNIT PROVISION 1 Cut and remove the center bar from A the radio housing. (Fig. A) 2 Snap the Double DIN brackets to the inside edge of the Double DIN trim plate. (Fig. B) 3 Slide the Double DIN head unit or stacked ISO head units into the bracket/radio housing assembly and B secure the Double DIN head unit or stacked ISO head units to the assembly using the screws supplied with the radio. (Fig. C) 4 Snap the double DIN trim plate into
ページ10に含まれる内容の要旨
99-5721 KIT ASSEMBLY CUSTOMIZING THE DISPLAY Changing The Display Back Light Color 1. Press the Passenger Heated Seat button for 10 seconds, the unit will go into “Configure Backlight Color” mode. The display will show “Red Green Blue” with number assigned to each color contributing to the overall back light color while in this mode. Each number will be between 0-255. 2. Press and hold the Fan + button to increase Red. 3. Press and hold the Fan - button to decrease Red. 4. Press and hold th
ページ11に含まれる内容の要旨
99-5721 KIT ASSEMBLY screen will then be displayed and the cursor will appear and blink. It will be located in the 1st location on the top row. 2. To modify the text : A. Use the FAN buttons to move the cursor forward or back. The location where the cursor is blinking is the location that the character may be changed. • FAN DOWN = Move Cursor ahead one location • FAN UP = Move Cursor back one location B. To change the character where the cursor is curr
ページ12に含まれる内容の要旨
99-5721 KIT ASSEMBLY Dual Zone Temperature Controls (allows 99-5721 to operate in a dual-zone climate controlled car) 1. Press the Temp Down and Passenger Heated Seat button simultaneously to enter Dual Zone Set Mode. Note: The ZONE icon will light to indicate that you are in dual zone mode, and the temperature bar graph will flash. 2. Press the Temp Up and Temp Down buttons to set the passenger temperature set point. 3. Press no buttons for 5 seconds and the temperature bar graph will s
ページ13に含まれる内容の要旨
99-5721 NOTES
ページ14に含まれる内容の要旨
99-5721 NOTES
ページ15に含まれる内容の要旨
99-5721 NOTES
ページ16に含まれる内容の要旨
INSTALLATION INSTRUCTIONS FOR PART 99-5721 METRA. THE WORLD’S BEST KITS.™ 1-800-221-0932 metraonline.com © COPYRIGHT 2004-2010 METRA ELECTRONICS CORPORATION REV. 9/09/2010
