ページ1に含まれる内容の要旨
®
AVerMedia
AVerDiGi EB1304 MOB
Mobile Security DVR System
User Manual
ページ2に含まれる内容の要旨
FCC NOTICE (Class B) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Federal Communications Commission Statement NOTE- This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
ページ3に含まれる内容の要旨
WARNING TO REDUCE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION IF THERE IS ANY DAMAGE, SHORTAGE OR INAPPROPRIATE ITEM IN THE PACKAGE, PLEASE CONTACT WITH YOUR LOCAL DEALER. WARRANTY VOID FOR ANY UNAUTHORIZED PRODUCT MODIFICATION. NOTICE - INFORMATION IN THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTIEC. - THE INFORMATION CONTAINED HEREIN IS TO BE CONSIDERED FOR REFERENCT ONLY.
ページ4に含まれる内容の要旨
Table of Contents Chapter 1 Introduction.......................................................................1 1.1 Package Content........................................................................................1 1.2 Features and Specifications .......................................................................2 1.3 Front Panel.................................................................................................3 1.4 Back Panel........................................
ページ5に含まれる内容の要旨
▲ ▼ FN EB DVR 1 2 3 4 5 6 7 8 9 0 A-B REC CT MENU SELE LEFT UP RIGHT ▲ FOCUS+ DOWN ZOOM+ ▼ FOCUS- ZOOM- PTZ SPEED- SPEED+ RM-H6 AVerMedia EB 1304 MOB Quick User Guide Chapter 1 Introduction AVerDiGi EB1304 MOB is a 4-channel stand-alone DVR unit for mobile solution that can be installed on the vehicle for security monitoring. It provides real-time monitoring and digital recording of surveillance video. Up to four video cameras and four sensor devices can be hooked up to this DVR unit. It als
ページ6に含まれる内容の要旨
(1) AVerMedia® AVerDiGi EB1304 MOB unit (2) Remote Control (batteries included) (3) Quick Installation Guide (4) Software CD (User Manual included) (5) Z-bracket x 2 (including 4 screws) (6) Removable hard disk drawer accessories (with spare screws) (7) Power cable (8) Camera Power cable (9) Extended IR Sensor cable (10) USB cable 1.2 Features and Specifications Non-PC stand-alone security digital video recorder 4 composite video inputs and 1 composite output VGA o
ページ7に含まれる内容の要旨
Removable hard disk drawer Multiple language OSD One USB 2.0 port for backup or playback 1.3 Front Panel (9) (8) (7) (1) (2) (3) (4) (5) (6) Name Function (1) Removable HDD : Lock/unlock the hard disk rack Keylock (2) USB 2.0 Port : Connect to PC for video backup or playback (3) Power Switch : Power on / off the DVR unit (4) IR Sensor : Receive signal from the remote control to operate the unit (5) IR Sensor Port : To connect extended IR sensor cable : Indicate running state of t
ページ8に含まれる内容の要旨
1.4 Back Panel (2) (4) (6) (9) (1) (3) (5) (7) (8) (10) (11) (12) Name Function (1) Audio In : Input the audio signal from a microphone or audio output device. The audio is embedded with channel 1 The audio input device must be power supplied by i external power. (2) Audio Out : Output the audio signal to a speaker The audio output device must be power supplied by i external power. (3) CH1 : Input the video camera signal and display it on channel 1 (4) CH2 : Input the video
ページ9に含まれる内容の要旨
1.5 Setting Up the DVR Unit 1.5.1 Installing the Hard Disk The DVR unit allows you to install one hard disk. Before installing the hard disk, make sure to set the hard disk master/slave jumper setting. Adjust the jumper setting according to the instructions on the hard disk label. Please set the jumper of hard disk as Master. Follow the illustrated instructions below to install the hard disk: 1. Using key to unlock the hard disk key 2. Pull removable hard disk drawer out lock 3. Conn
ページ10に含まれる内容の要旨
1.5.2 Mounting the DVR Unit The DVR unit can be mounted in two ways. User can uses the Z-brackets (4 screws included) to mount the DVR unit as the figure show below. 6
ページ11に含まれる内容の要旨
1.5.3 Connecting Devices The DVR unit can connect up to 4 video cameras, 4 sensor devices, 1 alarm device and output video to a TV or CRT/LCD monitor. Follow the illustration below to make the connection: - Each time you change the video display output, the power must be turned off and on to reset the DVR unit. - When the power cable is connected to vehicle batter, remember to stop recording and shutdown the DVR unit to avoid running out of vehicle battery when the vehicle engine is o
ページ12に含まれる内容の要旨
1.5.4 Connecting the Sensor/Relay device The Sensor and Alarm ports enable you to connect (4) sensor inputs and (1) relay outputs. Just connect the external sensor and relay pin directly to the pinhole. Check the table below and locate which pinhole is assigned to sensor input and relay output. 1.5.4.1 I/O Card Sensor and Relay pinhole allocation: The signal from the sensor (i.e., infrared sensors, smoke detectors, proximity sensors, door sensors, etc.) is being transmitted to the un
ページ13に含まれる内容の要旨
▲ ▼ 1.6 Familiarizing the Remote Control Buttons Use the Remote control to operate the OSD menu on surveillance screen. (5) FN DVR (1) (3 1 23 4 56 (2) 7 89 (4) 0 (6) (7) A-B (8) (9) (10) (11) REC (16) SELECT MENU (15) (12) LEFT UP RIGHT ▲ (13) FOCUS+ DOWN ZOOM+ ▼ - - FOCUS ZOOM PTZ SPEED- SPEED+ (14) RM-H6 Button Function Switch to Channel 1 (1) 1 As a number key for entering password Switch to Channel 2 (2) 3 As a number key for entering password Switch to Channel 3 (3) 7 As a n
ページ14に含まれる内容の要旨
▲ ▼ Button Function (8) To play the video Reverse the video playback at the speed of 2x, 4x 8x or 16x (9) To move the select to left Fast play the video playback at the speed of 2x, 4x 8x or 16x (10) To move the selection to right Stop playing / Stop recording (11) To move the select to down To enter the OSD Main menu / Exit from the main menu or sub-menu (12) display To move the selection to the left and right (13) ▲ To go up and down and select the items in the
ページ15に含まれる内容の要旨
Chapter 2 Operating the EB1304 MOB 2.1 Using the EB1304 MOB for the First Time For the fist time using the DVR unit, suggest user connect with the monitor and setup DVR unit by OSD menu. Once the DVR unit has been set up, user can use LED panel with remote control to modify setup of DVR unit. 2.1.1 Select the Setup Mode and Video System Before starting setup the DVR unit, please select the setup mode and video system. DVR unit has two setup modes – OSD and LED mode. By adjusting switch,
ページ16に含まれる内容の要旨
▼ 2.1.3 Set up the System Date and Time Before starting record video, adjust the date and time first. ▲ ▼ 1. Press to call up the OSD menu and then use and to go up and down and select Submenu. And then, press to confirm the selection. 2. In Submenu, select the Date and press again to make a selection. And then, ▲ ▼ use and to adjust the date and use and buttons to move the selection to the left and right. 3. To adjust Time, follow the above step 2 and 3. 4. Press to go back
ページ17に含まれる内容の要旨
▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲ 2.3.1 To Playback Video SEARCH METHOD 1. Press (play). TIME SEARCH EVENT LIST ▲ 2. Use the and ▼ or and buttons to go up and down and select TIME SEARCH or EVENT LIST. Then, press or (play) to make a selection. TIME SEARCH (search by date and time): TIME SEARCH HARD DISK : MASTER 1. In the selected HARD DISK, press or START TIME : 2006 / 05 / 04 10 : 00 : 01 ▲ . Then, use the and ▼ or END TIME : 2006 / 05 / 05 13 : 08 : 13 SEARCH TIME :
ページ18に含まれる内容の要旨
2. Listed below are the following recording conditions: A – Always Recording It records non-stop and automatically continue recording when interrupted. S – Sensor Recording It records when the sensor has activated. M – Motion Recording It records when any movement is detected B – Button Recording It records when the REC record button is pressed. 3. The “ ” play symbol would appear beside the channel number when you are in playback mode. 14
ページ19に含まれる内容の要旨
▲ Chapter 3 OSD Navigation Tree The follow figure is an OSD menu tree map. To call out the OSD menu, press button on the remote control. MAIN MENU RECORD SCHEDULE RECORD SCHEDULE CAMERA SELECT 123 4 123 4 00 : 00 - 01 : 00 ALWAYS REC 13 : 00 - 14 : 00 ALWAYS REC RECORD SELECT 123 4 123 4 01 : 00 - 02 : 00 ALWAYS REC 14 : 00 - 15 : 00 ALWAYS REC RECORD MODE D1 D 02 : 00 - 03 : 00 ALWAYS REC 15 : 00 - 16 : 00 ALWAYS REC VIDEO FORMAT MPEG4 03 : 00 - 04 : 00 ALWAYS REC 16 : 00 - 17
ページ20に含まれる内容の要旨
the and buttons to move the selection to the left and right. The red frame turns yellow when users are making a selection. If the unit is currently recording the video, user may have to stop video recording to change the settings. OSD MENU Description MAIN MENU CAMERA SELECT : CAMERA SELECT 123 4 RECORD SELECT 123 4 Enable/disable the channel number to display the video RECORD MODE D1 on the surveillance screen. VIDEO FORMAT MPEG4 RECORD FRAMERATE 60 RECORD SELECT
