ページ1に含まれる内容の要旨
installation instructions for Part 99-6507
APPLICATIONS
CHRYSLER
DODGE
300 2005-2007
Caliber 2007-2008
Aspen 2007
Charger 2005-2007
PT Cruiser 2006-2009
Dakota 2005-2007
Durango 2004-2007 JEEP
Commander 2006-2007
Magnum 2005-2007
Compass 2007-2008
Ram 2006-2008
Grand Cherokee 2005-2007
Ram 2500/3500 2009
Patriot 2007-2008
MITSUBISHI
Raider 2006-2007
NOTE: NON NAV MODELS ONLY
99-6507
KIT FEATURES
• DIN Radio Provi
ページ2に含まれる内容の要旨
99-6507 taBlE of contEnts Dash Disassembly - Chrysler Aspen 2007 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - Dodge Dakota 2005-2007 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - Dodge Durango 2004-2007 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - Dodge Charger 2005-2007 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - Dodge Magnum 200
ページ3に含まれる内容の要旨
DasH DisassEMBlY 99-6507 cHrYslEr asPEn 2007 DoDgE Dakota 2005-2007 DoDgE Durango 2004-2007 A Disconnect the negative battery terminal 1 to prevent an accidental short circuit. Remove (2) 7MM screws from the inside 2 of the pocket facing upward. (Figure A) B Unclip and remove the entire trim panel 3 surrounding the radio and climate controls. (Figure B) Remove (4) 7MM screws securing radio. 4 Unplug and remove radio.(Figure C) C Continue to kit assembly. 5 1
ページ4に含まれる内容の要旨
DasH DisassEMBlY 99-6507 DoDgE cHargEr 2005-2007 DoDgE MagnuM 2005-2007 A Disconnect the negative battery terminal 1 to prevent an accidental short circuit. Unclip and remove entire panel surrounding 2 radio and climate controls, including a/c vents. (Figure A) B Remove (4) 7MM screws securing radio. 3 Unplug and remove radio. (Figure B) Continue to kit assembly. 4 2
ページ5に含まれる内容の要旨
DasH DisassEMBlY 99-6507 cHrYslEr 300 2005-2007 A Disconnect the negative battery terminal 1 to prevent an accidental short circuit. Unclip and remove entire panel surround- 2 ing radio and climate controls, including a/c vents and clock. (Figure A) Remove (4) 7MM screws securing radio. 3 B Unplug and remove radio. (Figure B) Continue to kit assembly. 4 3
ページ6に含まれる内容の要旨
DasH DisassEMBlY 99-6507 DoDgE raM 2006-2008 witHout cEntEr consolE A Disconnect the negative battery terminal 1 to prevent an accidental short circuit. Open cup holder and remove (2) Phillips 2 screws facing up on front edge of radio/climate control panel. (Figure A) B Unclip and remove entire panel sur- 3 rounding radio and climate controls, including a/c vents. (Figure B) Remove (4) 7MM screws securing radio. 4 Unplug and remove radio. Continue to kit assembly. 5 4
ページ7に含まれる内容の要旨
DasH DisassEMBlY 99-6507 DoDgE raM 2006-2008 witH Mini cEntEr consolE A Disconnect the negative battery terminal 1 to prevent an accidental short circuit. If vehicle has floor shifter, remove shifter 2 knob. Remove center console inserts, if present. 3 (Figure A) Remove screws securing the rear center 4 console to the floor panel. Lift up on the rear center console to clear the gear shift B lever, if present. (Figure B) Remove screws securing the front center 5 console to the floor panel. Un
ページ8に含まれる内容の要旨
DasH DisassEMBlY 99-6507 DoDgE raM 2006-2008 witH full cEntEr consolE A Disconnect the negative battery terminal 1 to prevent an accidental short circuit. If vehicle has floor shifter, remove shifter 2 knob. Unsnap and remove console front top 3 cover (closest to the dash). (Figure A) B Remove two 8 mm screws from under 4 console cover (previously removed). Remove front section of console. (Figure B) Loosen two 8 mm screws at bottom of 5 dash. Unsnap lower panel. Remove (2) Phillips screws f
ページ9に含まれる内容の要旨
P R N D L DasH DisassEMBlY 99-6507 DoDgE caliBEr 2007-2008 JEEP coMPass 2007-2008 JEEP Patriot 2007-2008 A Disconnect the negative battery terminal 1 to prevent an accidental short circuit. Unsnap and move shifter trim to the side. 2 (Figure A) 1 2 3 4 5 6 (Compass and Patriot only) Unspap and 3 remove top center dash panel above AC vents. D L Unsnap center dash trim panel (do not 4 remove until climate controls are removed). (Figure A) Remove (4) Phillips screws holding 5 climate control panel
ページ10に含まれる内容の要旨
DasH DisassEMBlY 99-6507 JEEP granD cHErokEE 2005-2007 A Disconnect the negative battery terminal 1 to prevent an accidental short circuit. Unsnap and remove panel from around 2 radio including the vent on each side. (Figure A) B Remove (4) 7MM screws securing radio. 3 Unplug and remove radio. (Figure B) Continue to kit assembly. 4 8
ページ11に含まれる内容の要旨
DasH DisassEMBlY 99-6507 JEEP coMManDEr 2006-2007 Disconnect the negative battery terminal 1 to prevent an accidental short circuit. Remove the (16) screws securing the 2 Figure A) radio trim panel. ( A 4 screws 4 screws 4 screws 4 screws Unclip and remove the entire radio trim 3 panel. (Figure B) B Remove (4) 7MM screws securing radio. Unplug and remove radio. 4 Continue to kit assembly. 5 9
ページ12に含まれる内容の要旨
DasH DisassEMBlY 99-6507 cHrYslEr Pt cruisEr 2006-2009 A Disconnect the negative battery terminal 1 to prevent an accidental short circuit. Remove (2) screws from inside air vents 2 on center dash panel. (Figure A) Unsnap center dash panel (do not remove 3 until climate controls are removed). (Figure A) Remove (4) Phillips screws holding climate 4 control panel to backside of the center dash panel. Remove (4) Phillips screws holding climate 5 control panel to backside of the center dash panel
ページ13に含まれる内容の要旨
DasH DisassEMBlY 99-6507 MitsuBisHi raiDEr 2006-2007 A Disconnect the negative battery terminal 1 to prevent an accidental short circuit. Unsnap and remove center dash panel. 2 (Figure A) Remove (4) 7MM screws securing radio. 3 Unplug and remove radio. Continue to kit assembly. 4 11
ページ14に含まれる内容の要旨
kit assEMBlY 99-6507 Din raDio Provision witH PockEt A NOTE: You will need to remove the aftermarket radio’s trim ring if equipped. Slide the DIN cage into the Radio 1 Housing and secure by bending the metal locking tabs down. (Figure A) B Slide the after-market head unit into 2 the cage and secure. (Figure B) C Using the alignment pins on the 3 trim plates & the corresponding holes in the housing, attach the upper trim plate and the lower trim plate supplied with the kit. Figure C Continue to
ページ15に含まれる内容の要旨
kit assEMBlY 99-6507 iso raDio Provision witH PockEt NOTE: You will need to remove the A aftermarket radio’s trim ring if equipped. Mount the ISO Brackets to the 1 radio using the screws supplied with the radio. Figure A B Slide the radio into the opening 2 until it snaps into place. Figure B Using the alignment pins on the 3 trim plates & the corresponding holes in the housing, attach the upper trim plate and the lower trim plate supplied with the kit. Figure B Continue to Final Assembly. 4 13
ページ16に含まれる内容の要旨
final assEMBlY 99-6507 final assEMBlY A A) Strip wire ends back 1/2" B B) Twist ends together C) Solder C D) Tape D Locate the factory wiring harness in the dash. Metra recommends using the 1 proper mating adapter and making connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.) Secure the kit into the sub dash using the (4) 7mm screws that secured 2 the factory radio. Re-connect the negative battery terminal and test the un
