ページ1に含まれる内容の要旨
Digital Video Recorder
User Manual
CBC V 0.4
ページ2に含まれる内容の要旨
Table of Contents 1. Introduction 1-1 Safety Warning ……………………………………………………………………………..…… 3 1-2 Features ……………………………………………………………………………………..…… 4 1-3 Specifications ………………………………………………………………………………..…... 5 2. Installation 2-1 Package contents ………………………………………………………………………………. 6 2-2 Connection ………………………………………………………………………………………. 6 2-3 RS232 Remote protocol ………………………………………………………………………..… 7 3. Configuration 3-1 Install HDD ……………………………………………………………………………………… 8 3-2 Front panel keypad ……………………
ページ3に含まれる内容の要旨
1. Introduction We thank you for choosing this high quality Digital Video Recorder. The DVR converts analog NTSC or PAL video to digital images and records them on a removable hard disk drive. Digitally recorded video has several advantages over analog video recorded on tape. There is no need to adjust tracking. Digital video can be indexed by time schedule or events, and you can instantly view video after selecting the time or event. You can freeze frames, fast-forward, fast-reverse, slow
ページ4に含まれる内容の要旨
1.2 Features 1.2.1 Replace traditional Time-Lapse VCR. Compatible with most multiplexer and quad processors. 1.2.2 Compatible with NTSC / PAL 1.2.3 Record speed options: NTSC : Maximum 60 Images / second, minimum 1 Image / second PAL : Maximum 50 Images / second, Minimum 1 Image / second 1.2.4 Recording quality selection Recording video quality and resolution for Best / High / Normal / Basic 1.2.5 Quick search modes Search video by Last Record, Full List, Alarm List & Time Se
ページ5に含まれる内容の要旨
1.3 Specifications VIDEO FORMAT NTSC / EIA or PAL / CCIR HDD STORAGE IDE type, UTMA 66 above, 1 removable HDD supported RECORD MODE Manual / Alarm / External / Timer PLAYBACK SEARCHING Date & Time / Event / Alarm searching RS232 Yes O.S.D. (On Screen Display) Yes SECURITY Password protection VIDEO INPUT 1 video input, composite 1 Vp-p / 75ohm (BNC) VIDEO OUTPUT 1 video output , composite 1 Vp-p/75ohm (BNC) VIDEO RESOLUTION 720 x 576 (PAL), 720 x 486 (NTSC) VIDEO COMPRESSION Wavelet
ページ6に含まれる内容の要旨
2. Installation 2.1 Package contents The package contents including the following items. Single channel Digital Video Recorder HDD cartridge Key for cartridge (In HDD cartridge) Power cord User manual Rack mounting kit 2.2 Connection 2.2.1 Connect with single camera Main Monitor Video Camera 1 Alarm Sensor VIDEO OUT Alerm Input PC VIDEO IN RS232 DVR 6
ページ7に含まれる内容の要旨
2.2.2 Connect with Multiplexer Video Camera Main Monitor . . . . 16 21 Alarm .. . . Sensor Alarm Input PC RS232 GND VCR OUT VCR IN DVR 2.3 RS232 Remote Protocol You can use the PC key board to simulate DVR key pad. DATA: REMOTE PROTOCOL using 8 bit data、1 start bit、1stop bit ACT C0H ID FUNCTION STOP (FFH) (7FH) FUNCTION CODE ASCII FUNCTION CODE ASCII MENU 0x4D M DOWN / STOP 0x4E N ENTER 0x0D ENTER L
ページ8に含まれる内容の要旨
3.1 Install HDD 3.1.1 Installing Hard Drive into Cartridge 3.1.1.1. Please find the Key in the Cartridge. 3.1.1.2. Pull the active-handle outwards and use the miniature key provided and insert into the key hole, turning the key anti-clockwise, then the handle will auto-eject for pulling out.。 3.1.1.3. Pull the handle outwards to remove the carrier body away from the cartridge frame. 3.1.1.4. Push the open button to slide the top cover backwards and remove. 3.1.1.5. Insert the DC power c
ページ9に含まれる内容の要旨
PAL/NTSC SYSTEM (Unit : hours) Fields Delay 1 2 4 6 8 12 16 20 24 32 40 48 56 64 Best 12 24 48 72 96 144 192 240 288 384 480 576 672 768 Record High 15 30 60 90 120 180 240 300 360 480 600 720 840 960 Quality Normal 24 48 96 144 192 288 384 480 576 768 960 1152 1344 1536 Basic 40 80 160 240 320 480 640 800 960 1280 1600 1920 2240 2560 HDD Type 120GB Note: Above data is from actual test by recording normal TV program. (Reference only)
ページ10に含まれる内容の要旨
Please follow following descriptions to operate this device. 13 HDD HDD FULL TIMER ALARM MENU ENTER SEARCH SLOW PLAY REC POWER REW FF STOP 10 11 12 7 8 1 2 3 4 5 9 6 1. Install HDD This device comes with a removable hard disk drive tray. Before turning on this device, you must install hard disk drive (not including in standard (package), and make it ready to operate. 2. MENU Press MENU to enter main menu operation mode, and press administrator password (defa
ページ11に含まれる内容の要旨
12. PLAY Press PLAY to play recorded video. 13. LED Light: Under following condition, the led light is ON. (1) HDD : HDD is activated (2) HDD FULL：HDD is full (3) ALARM：When Alarm Enable : Yes (when alarm is triggered, the led is flashing) (4) TIMER：When Timer Enable : Yes (5) PLAY：Play operation (6) REC：Recording operation (7) POWER : Power On/Off 3.3 Back panel connection 4 1 VIDEO IN POWER ALARM VIDEO OUT 23 1. VIDEO IN Connect to video source, such as
ページ12に含まれる内容の要旨
25 pin com port 9 pin com port 12
ページ13に含まれる内容の要旨
PIN 1. RS232-TX : RS-232 DVR can be controlled remotely by an external device or control system, such as a control keyboard, using RS-232 serial communications signals. PIN 2. RS232-RX : RS-232 DVR can be controlled remotely by an external device or control system, such as a control keyboard, using RS-232 serial communications signals. PIN 3. VIDEO LOSS When video loss happen, it will send a signal to trigger another accessory. This pin output becomes “Low” when video
ページ14に含まれる内容の要旨
alarm triggered, COM disconnect with NC, and connect with NO. PIN 8. EXTERNAL ALARM NO Under normal operation COM connect with NC and disconnect with NO. But when Alarm triggered, COM disconnect with NC, and connect with NO. PIN 9. GND GROUND PIN 10. RS485-B DVR can be controlled remotely by an external device or control system, such as a control keyboard, using RS485 serial communications signals. PIN 11. RS485-A DVR can be controlled remotely by an external de
ページ15に含まれる内容の要旨
To press ”MENU” to enter main menu. You will need to enter password to access main menu. To press “ ◄” “ ►” to move digit, and to press ” ▲” “▼” to select number. To press ”ENTER” button to confirm password. Password : 0000 Ex.: Password : 0000 (Default : 0000) After keying in correct password, and confirm by pressing ”ENTER” button, screen will show (Menu) ► Timer following options. Record Timer ------- Scheduling Record Alarm Record -------
ページ16に含まれる内容の要旨
To press ”▲” “▼” to choose item. (Menu) Timer Timer Record Record Alarm Alarm Remote Remote ► System ► System Event Event (System) To choose System item, and press “ENTER” ► Buzzer : On button to enter System Setup mode. It will be HDD Overwrite : No Message Latch : No shown as right screen Date Display : Y- M - D Date : 2002-JUL-14(SUN) Time : 22:38:29 New Password
ページ17に含まれる内容の要旨
3.5.2.1 Press ”▲” “▼” to choose Message Latch 3.5.2.2 Press “Enter” to confirm Message Latch 3.5.2.3 Press ”▲” “▼” to choose Message Latch : Yes / No Yes : Turn Message Latch on, the message will show in the screen. No : Turn Message Latch off, the message will retain only 10 seconds. 3.5.2.4 Press Menu to exit and confirm the current operation. 3.5.2.5 Press again Menu to exit and close System Setup mode 3.5.4 On Screen Display ( date display ) format : Y-M-D, M-D-Y, D-M-Y, and OFF
ページ18に含まれる内容の要旨
3.5.7.1 Press ”▲” “▼” to choose new password : xxxx setup. 3.5.7.2 Press “Enter” to confirm new password : xxxx setup. 3.5.7.3 Press ”▲” “▼” to choose number, and press “ ◄” “ ►” to move digit location. 3.5.7.4 Press Menu to exit and confirm current operation. 3.5.7.5 Press again Menu to exit and close System Setup mode 3.5.8 Clear HDD Yes / No setup 3.5.8.1 Press ”▲” “▼”to choose clear HDD setup. 3.5.8.2 Press “Enter” to confirm clear HDD setup. 3.5.8.3 Press ”▲” “▼”to choose clear H
ページ19に含まれる内容の要旨
No : Confirm not to System Reset 3.5.9.4 Press Menu to exit and confirm current operation. 3.5.9.5 Press again Menu to exit and close System Setup mode. Note: If operation without any action until 60 seconds, it will close the setup mode. 3.6 Schedule Time-Lapse record mode setup (Timer) 3.6.1 Enter “ Timer “ setup To press ”MENU” to enter main menu. You will need to enter password to access main menu. To press “ ◄” “ ►” to move digit, and to press ”▲” “▼” to select number.
ページ20に含まれる内容の要旨
(Timer) To choose Timer item, and press “ENTER” button Day Start End F-D to confirm Timer Record setup mode. It will be Daily 00:00 00:00 Off Daily 00:00 00:00 Off shown as right screen Daily 00:00 00:00 Off Daily 00:00 00:00 Off Daily 00:00 00:00 Off Daily 00:00 00:00 Off Daily 00:00 00:00 Off Timer Enable: No 3.6.2 Timer Record Setup: 3.6.2.1 Press “Enter” to confirm Timer Record day setup. 3.6.2.2 Press ”▲” “▼” to choose
