ページ1に含まれる内容の要旨
INSTALLATION INSTRUCTIONS FOR PART 99-7504
APPLICATIONS
Mazda 3
2004-2009
99-7504
KIT FEATURES
• DIN Mount Radio Provision with Pocket
• ISO Mount Radio Provision with Pocket
• Bonus Display Replacement Pocket
• Retains Factory Display For Automatic
Climate Controls
KIT COMPONENTS
A) Radio Housing • B) ISO Brackets • C) Trim Plate • D) Display Replacement Pocket
• E) Display Retention Brackets • F) (2) 3/8” #10 Bolts and (2) #10 Nuts • G) (2) PC-7503 Panel Clips
D
E
C
B
A
WIRING A
ページ2に含まれる内容の要旨
99-7504 TABLE OF CONTENTS Dash Disassembly - Mazda 3 2004-2009. ... ... .... ... .... ... .... . . . . . . . . 1 Kit Assembly - Display Brackets/Pocket Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - DIN Mount Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . . . 3 - ISO DIN Mount Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . 4 Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5,6 *Note:
ページ3に含まれる内容の要旨
LOAD CLOCK SET AM CD FM1/2 TAPE/MD 99-7504 DASH DISASSEMBLY MAZDA 3 2004-2009 A 1 Disconnect the negative battery ter- minal to prevent an accidental short circuit. 2 Unclip and remove display trim panel above radio. Tip: Open glove box and start in middle of panel working towards drivers side first because last HOOK connection on far passenger side is a hook. (Figure A) 3 Remove (2) Phillips screws exposed at top of radio then unclip and B remove radio. Note: Display is attached to radio bracke
ページ4に含まれる内容の要旨
99-7504 DISPLAY/POCKET ASSEMBLY DISPLAY BRACKETS/POCKET ASSEMBLY MAZDA 3 2004-2009 AUTOMATIC CLIMATE CONTROL VEHICLES A 1 Using the (2) 3/8” #10 bolts and (2) #10 nuts attach the display retention brackets to the display unit. 2 Remove the (2) Phillips screws in the sub dash. (Figure A) 3 Secure the display unit into the sub dash using the screws removed in the previous step. MANUAL CLIMATE CONTROL VEHICLES B 1 Using the (2) Phillips screws removed in step 4 of Dash Disassembly secure the displ
ページ5に含まれる内容の要旨
99-7504 KIT ASSEMBLY DIN MOUNT RADIO PROVISION *Note: Refer also to the instructions included with the aftermarket radio. A 1 Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs down. (Figure A) 2 Slide the aftermarket radio unit into the cage and secure. (Figure B) 3 Snap the Trim plate into the Radio Housing. (Figure B) 4 Attach the (2) PC-7503 panel clips to B the rear of the radio housing. (Figure C) Continue to final assembly. C 3
ページ6に含まれる内容の要旨
99-7504 KIT ASSEMBLY ISO DIN MOUNT RADIO PROVISION *Note: Refer also to the instructions included with the aftermarket radio. A 1 Mount the ISO Brackets to the after- market radio using the screws sup- plied with the radio. (Figure A) 2 Slide the radio into the radio housing until it snaps into place. (Figure B) 3 Attach the trim plate supplied with the kit to the front of the radio hous- ing assembly. (Figure B) 4 Attach the (2) PC-7503 panel clips to B the rear of the radio housing. (Figure C)
ページ7に含まれる内容の要旨
99-7504 FINAL ASSEMBLY FINAL ASSEMBLY A (A) Strip wire ends back 1/2" B B) Twist ends together C) Solder D) Tape C D 1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individ- ually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation. 3 Reassemble radio and dash assemblies in reverse order of disas
ページ8に含まれる内容の要旨
FINAL WIRING CONNECTIONS Make wiring connections using the EIA color code chart shown below and the instructions included with the head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and individually tape off ends of any unused wires to prevent electrical short circuit. METRA / EIA WIRING CODE 12V Ignition / Acc. . . . . . . . . . Red Right Front (+) . . . . . . . . . . . . Gray 12V Batt / Memory. . . . . . . . . Yellow Right Front (-). . . . . . .
