Manual do usuário Metra Electronics 99-7504

Resumo do conteúdo contido na página número 1

INSTALLATION INSTRUCTIONS FOR PART 99-7504
APPLICATIONS
Mazda 3
2004-2009
99-7504
KIT FEATURES
• DIN Mount Radio Provision with Pocket
• ISO Mount Radio Provision with Pocket
• Bonus Display Replacement Pocket
• Retains Factory Display For Automatic
Climate Controls
KIT COMPONENTS
A) Radio Housing • B) ISO Brackets • C) Trim Plate • D) Display Replacement Pocket
• E) Display Retention Brackets • F) (2) 3/8” #10 Bolts and (2) #10 Nuts • G) (2) PC-7503 Panel Clips
D
E
C
B
A
WIRING A

Resumo do conteúdo contido na página número 2

99-7504 TABLE OF CONTENTS Dash Disassembly - Mazda 3 2004-2009. ... ... .... ... .... ... .... . . . . . . . . 1 Kit Assembly - Display Brackets/Pocket Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - DIN Mount Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . . . 3 - ISO DIN Mount Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . 4 Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5,6 *Note:

Resumo do conteúdo contido na página número 3

LOAD CLOCK SET AM CD FM1/2 TAPE/MD 99-7504 DASH DISASSEMBLY MAZDA 3 2004-2009 A 1 Disconnect the negative battery ter- minal to prevent an accidental short circuit. 2 Unclip and remove display trim panel above radio. Tip: Open glove box and start in middle of panel working towards drivers side first because last HOOK connection on far passenger side is a hook. (Figure A) 3 Remove (2) Phillips screws exposed at top of radio then unclip and B remove radio. Note: Display is attached to radio bracke

Resumo do conteúdo contido na página número 4

99-7504 DISPLAY/POCKET ASSEMBLY DISPLAY BRACKETS/POCKET ASSEMBLY MAZDA 3 2004-2009 AUTOMATIC CLIMATE CONTROL VEHICLES A 1 Using the (2) 3/8” #10 bolts and (2) #10 nuts attach the display retention brackets to the display unit. 2 Remove the (2) Phillips screws in the sub dash. (Figure A) 3 Secure the display unit into the sub dash using the screws removed in the previous step. MANUAL CLIMATE CONTROL VEHICLES B 1 Using the (2) Phillips screws removed in step 4 of Dash Disassembly secure the displ

Resumo do conteúdo contido na página número 5

99-7504 KIT ASSEMBLY DIN MOUNT RADIO PROVISION *Note: Refer also to the instructions included with the aftermarket radio. A 1 Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs down. (Figure A) 2 Slide the aftermarket radio unit into the cage and secure. (Figure B) 3 Snap the Trim plate into the Radio Housing. (Figure B) 4 Attach the (2) PC-7503 panel clips to B the rear of the radio housing. (Figure C) Continue to final assembly. C 3

Resumo do conteúdo contido na página número 6

99-7504 KIT ASSEMBLY ISO DIN MOUNT RADIO PROVISION *Note: Refer also to the instructions included with the aftermarket radio. A 1 Mount the ISO Brackets to the after- market radio using the screws sup- plied with the radio. (Figure A) 2 Slide the radio into the radio housing until it snaps into place. (Figure B) 3 Attach the trim plate supplied with the kit to the front of the radio hous- ing assembly. (Figure B) 4 Attach the (2) PC-7503 panel clips to B the rear of the radio housing. (Figure C)

Resumo do conteúdo contido na página número 7

99-7504 FINAL ASSEMBLY FINAL ASSEMBLY A (A) Strip wire ends back 1/2" B B) Twist ends together C) Solder D) Tape C D 1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individ- ually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation. 3 Reassemble radio and dash assemblies in reverse order of disas

Resumo do conteúdo contido na página número 8

FINAL WIRING CONNECTIONS Make wiring connections using the EIA color code chart shown below and the instructions included with the head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and individually tape off ends of any unused wires to prevent electrical short circuit. METRA / EIA WIRING CODE 12V Ignition / Acc. . . . . . . . . . Red Right Front (+) . . . . . . . . . . . . Gray 12V Batt / Memory. . . . . . . . . Yellow Right Front (-). . . . . . .