ページ1に含まれる内容の要旨
INSTALLATION INSTRUCTIONS FOR PART 99-7326
APPLICATIONS
Hyundai Elantra 2007-2010
(US Model Only)
(Non Radio Delete)
(Non Touring Model)
99-7326
KIT FEATURES
• DIN Radio Provision with Pocket
• ISO Radio Provision with Pocket
KIT COMPONENTS
A) Radio Housing B) ISO Brackets C) Trim Plate
C
B
A
WIRING AND ANTENNA CONNECTIONS (Sold Separately)
Harness:
• 70-1004 - Hyundai 2006-up /KIA harness 2004-up
• 70-7303 - Hyundai/KIA harness 2009
Antenna Adapter:
• 40-KI11 - KIA antenna adapter 2007-up
ページ2に含まれる内容の要旨
99-7326 TABLE OF CONTENTS Dash Disassembly - Hyundai Elantra 2007-2010 .... ........ ....... ........ ........ .....1 Kit Assembly - DIN Radio Provision with Pocket .... ....... ........ ........ . ...... 2 - ISO Radio Provision with Pocket .... ....... ........ ........ .. ..... .3 Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 *Note: Refer also to the instructions included with the aftermarket radio.
ページ3に含まれる内容の要旨
2 A/C 1 3 4 99-7326 DASH DISASSEMBLY HYUNDAI ELANTRA 2007-2010 A 1 Disconnect the negative battery ter- minal to prevent an accidental short circuit. 2 Unclip and remove the panel sur- rounding the radio including the a/c vents and hazard button. (Figure A) Remove (4) Phillips screws to remove 3 radio. Continue to kit assembly. B 1
ページ4に含まれる内容の要旨
99-7326 KIT ASSEMBLY DIN RADIO PROVISION WITH POCKET *Note: Refer also to the instructions included with the aftermarket radio. A Note: The trim plate supplied with the 99-7326 is required for a complete installation. ISO mounting may be pre- ferrred as it is easier than DIN mount- ing and using this trim plate. 1 Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs outward. (Figure A) 2 Slide the aftermarket radio into the cage until it snaps into place. (Figur
ページ5に含まれる内容の要旨
99-7326 KIT ASSEMBLY ISO RADIO PROVISION WITH POCKET *Note: Refer also to the instructions included with the aftermarket radio. A 1 Mount the ISO Brackets to the after- market radio using the screws sup- plied with the radio. (Figure A) 2 Slide the radio into the radio opening until the side clips snap into place. (Figure B) 3 Snap the trim plate onto the front of the Radio Housing. (Figure B) Continue to final assembly. B 3
ページ6に含まれる内容の要旨
99-7326 FINAL ASSEMBLY FINAL ASSEMBLY A (A) Strip wire ends back 1/2" B B) Twist ends together C) Solder D) Tape C D 1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individ- ually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation. 3 Reassemble radio and dash assemblies in reverse order of disas
ページ7に含まれる内容の要旨
99-7326 NOTES 5
ページ8に含まれる内容の要旨
99-7326 INSTRUCTIONS 1-800-221-0932 www.metraonline.com REV. 04/27/10 © COPYRIGHT 2004-2010 METRA ELECTRONICS CORPORATION INST99-7326
