ページ1に含まれる内容の要旨
Use and Care Guide
®
LiquidPropaneGasGrill
Kenmore Model No. 415.16110800
This Grill is For
Outdoor Use Only
• Read this manual before cooking on
grill. Failure to follow all
manufacturer's instructions could
result in fire or e×plosion which could
cause property damage, personal
injury or death.
• Combustion by=products produced
when using this product contain
• Parts • Use and Care
chemicals known to the State of
California to cause cancer, birth
• Assembly • Troubleshooting
defects, or other
ページ2に含まれる内容の要旨
CALIFORNIA PROPOSITION65 if you smell gas: 1. Combustion by-products producedwhen using this product contain chemicals known to the State of 1. Shut off gas to the appliance. California to cause cancer, birth defects, and other reproductive harm. 2. Extinguish any open flame. 2. This product contains chemicals, including lead 3. Open lid. and lead compounds, known to the State of 4. if odor continues, keep away from the California to cause cancer, birth defects or other appliance and immediately
ページ3に含まれる内容の要旨
For Your Safety ...................................... 2 KENMORE GRILL WARRANTY Grill Service Center................................... 2 Product Record Information ............................ 2 One Year Full Warranty on Kenmore Grill If this grill fails due to a defect in material or workmanship Safety Symbols ...................................... 2 within one year from the date of purchase, call 1-800-4-MY Installation Safety Precautions .......................... 2 HOME®to arrange for free
ページ4に含まれる内容の要旨
LP Cylinder • The LP cylinder used with your grill must meet the following requirements: • Use LP cylinders only with these required measurements: 12" (30.5cm) (diameter) x 18" (45.7 cm) (tall) with 20 lb. (9 kg.) capacity maximum. , LP cylinders must be constructed and marked in accordance with specifications for LP cylinders of the U.S. Department of • NEVER store a spare LP tank under or near grill or in Transportation (DOT) or for Canada, CAN/CSA-B339, enclosed areas cylinders, spheres and t
ページ5に含まれる内容の要旨
LP Tank Exchange Connecting Regulator To The LP Tank o Many retailers that sell grills offer you the option of replacing 1. LP tank must be properly secured onto grill. (Refer to assembly section.) your empty LPtank through an exchange service. Useonly those reputable exchange companies that inspect, precision fill, 2. Turn all control knobs to the OFF position. test and certify their cylinders. Exchange your tank only for an OPB safety feature-equipped tank as described in the 3. Turn LP tank O
ページ6に含まれる内容の要旨
Leak Testing Valves, Hose and Regulator 1. Turn all grill controlknobs to OFF. , Be sure regulator is tightly connected to LP tank. 3. Completely open LP tank valve by turning OPD hand wheel counterclockwise. If you hear a rushing sound, turn gas off immediately. There is a major leak at the connection. Correct before proceeding by calling Sears for replacement parts at 1-800-4-MY-HOME®. Hold couplingnutand regulator 4. Brush soapy solution onto areas where bubbles are shown in as shown for prop
ページ7に含まれる内容の要旨
Safety Tips ,A. Before opening LP cylinder valve, check the coupling nut for tightness. For Safe Use Of Your Grill And To Avoid Serious A When grill is not in use, turn offall control knobs and LP cylinder valve. injury: A Never move grill while in operation or still hot. • Do not let children operate or play near grill. ,A. Use long-handled barbecue utensils and oven mitts to avoid • Keep grill area clear and free from materials that burn. burns and splatters. • Do not block holes in bottom or
ページ8に含まれる内容の要旨
Before Your First Cookout Main burner Ignitor Lighting A Do not lean over grill while lighting. . Light burners, check to make sure they are lit, close the lid and 1. Open lid during lighting. warm up grill on HIGH for 15 minutes. This curing of paint and 2. Turn ON valve from source or tank. parts will produce an odor only on first lighting. 3. Push and turn Ignition Burner control knob to _- HI and Burner Flame Check immediately press and hold Electronic Ignition button. , Light burner, rotate
ページ9に含まれる内容の要旨
Turning Grill Off . Turn all knobs to OFF position. Turn LP tank off by turning CAUTION l 11 OPD hand wheel clockwise to a full stop. Ignitor Check SPIDER ALERT! • Turn gas off at LP tank. Press and hold ignitor button. "Click" should be heard and spark seen each time between collector GASCOLLECTOR box or burner and electrodes. See "Troubleshooting"if no click or spark. Valve Check • important: Make sure gas is off at LP tank before checking valves. Knobs lock in OFF position. To check valves, f
ページ10に含まれる内容の要旨
Storing Your Grill Cleaning the Burner Assembly Follow these instructions to clean and/or replace parts of burner o Clean cooking grates. assembly or if you have trouble igniting grill. o Store in dry location. 1. Turn gas off at control knobs and LP cylinder, o When LP tank is connected to grill, store outdoors in well- 2. Remove cooking grate and vaporiser bar. ventilated space and out of reach of children. 3. Under grill remove grease cup, disconnect ignitor wire and o Cover grill if stored o
ページ11に含まれる内容の要旨
Description ......................... Part# Key _y Description ........................ Part # 1 2 44 1 Grate,SideBurner................... 80009728 UpperLeg .......................... 80010075 2 1 Leg,LeftFront ....................... 80010080 45 1 SidebumerClip...................... 80015912 3 1 Leg,LeftBack ....................... 80010079 46 1 WingNut........................... 80015912 4 1 Leg,RightFront...................... 80010077 47 3 #8X3/8"Self-TapScrew ............... 80015912 5 1 L
ページ12に含まれる内容の要旨
G ® _b ® \ ,# (_/-o 12 °464810408
ページ13に含まれる内容の要旨
LeftLeg Placeoneupperlegas shown. NOTE:Leftfrontandleftbacklegsdonot havelegextenders.In front,attachupperleg, side braceandleftfrontleg(curve)with#10-24x1-1/4"screw and#10-24flange nut. In back,attach upperleg,sidebraceandleft backleg(straight)with #10-24x1-1/4"screw and#10-24flange nut. Do not tighten. Attachsupportbracketinsecondholefrombottomof legwithhingepinsand hitchpins (A). S UpperLeg 11 HitchPin _Brace Qty.2 LeftFrontLeg 13 10 (Curve) 12 HingePin #10-24x1-1/4" Qty.2 Screw Cff LeftBackL
ページ14に含まれる内容の要旨
Hooktankexclusionwire intolegswithopeningfor LPcylinderonside braceside. TankExclusionWire \ SideBrace Largeropeningside TankExclusionWire Lay front legs down on the floor. D Upperand Lower Panels Fit upperpanelwithtwotabsbetweenlegs.Attachwith#10-24x2"screws and#10-24 flange nuts. Fit lowerpanelaroundtankexclusionwire andattachwith#10-24x2"screws and#10-24flange nuts. 17 UpperPanel 13 17 #10-24x2"Screw Qty.8 13 #10-24Nut LowerPanel Qty.8 14. 464810408
ページ15に含まれる内容の要旨
Back Bracesto Cart Removepreviouslyattachedscrewsandnutsfromupperlegsasshown.Attachbackbraceswith#10-24x1-1/4"screws and #10-24flange nuts. BackBrace / 12 #10-24xl -1/4" Remove screws and Screw nuts to attach backbrace Qty. 6 12 13 #10-24FlangeNut Qty.6 BackBrace Wheels Turnassemblyupsidedown. Insertaxlerodthroughwheel,legsandotherwheel.Attachwitha wheelbushingandhitchpin. 21 WheelBushing7 Qty.1 11 Axle Rod Wheel HitchPin Qty.1 "Cone" side of wheel against leg 464810408.15
ページ16に含まれる内容の要旨
Control Paneland Upper FireboxSupports Standcartupright. In front, fit controlpanelbetweenleftand rightlegs. Insert#10-24x2"screws to hold panelin place. Placeupperfirebox supportsontoscrewsmakingsure angleside is facingthefront andattachwith #10-24flange nuts, In back,attachupperfireboxsupportwith#10-24x2" screws and#10-24flange nuts, 17 ControlPanel ,,,_ \ UpperFirebox Support 17 #10-24x2"Screw Qty.8 13 #10-24FlangeNut Qty.8 Valve/Hose/Regulatorand Electronic ignitionModule Attachvalve/hose/re
ページ17に含まれる内容の要旨
HeatShield Attach heatshieldwith#10-24x1/2"screws and#10-24flange nuts. HeatShield 27 27 #10-24Xl/2" Screw Qty.2 13 #10-24FlangeNut Qty.2 Tank Retainer Inserttankretainerintoside braceandsecurewithwingscrew. 30 WingScrew Qty.1 S Retainer 464810408• 17
ページ18に含まれる内容の要旨
Burner, Firebox and Control Knobs Placeburnerassemblyintofirebox(A).Fastenthe burnerassemblyto thefireboxusing5ramfiber washers and#10-24x 1/2" machinescrews. Placefireboxontoupperfireboxsupportswithburnertubesbelowheatshield.Makesure burner tubesare correctly engaged. If burneris notleveledfromleftto right,adjustthe twoscrewsattachingvalvestemsto controlpanel.Attachignitorwireto ignitor (B). Attachfireboxwith#10-24x1/2"screws, 5ramfiber washers and#10-24flange nuts (C). Pushcontrolknobsonto val
ページ19に含まれる内容の要旨
Shelves Insertmountingbracketsintoside shelfsupportswith#10-24x1/2"screws (A). Attachbackof legwith1/4"-20x1-1/4"screws and!/4"-20 flange nuts, Donotfullytighten.Attachmountingbracketstofrontof legwith1/4"-20x1/2"screws (B). Fullytightenallscrews. Repeatabovestepsto attachsideburnershelfto cart. 27 40 41 #10-24x1/2" 1/4"-20xl/2" 1/4"-20FlangeNut Screw Screw Qty.4 Qty.8 Qty.4 39 1/4"-20xl-1/4" Screw Qty.4 A \ MountingBracket ShelfSuppod SideShelf(WithoutHole) / 41 4O 464810408.19
ページ20に含まれる内容の要旨
Sideburner Attachsideburnervalvewith#8-32x3/8"machinescrews (A). Attachsidebumerpanwith#8x3/8"self-tap screws and5mm ID9mmODfiber washers.Placesideburnerinto shelf(B). Makesurevalveis insidesidebumertube.Attachsideburnerwith wing nut and 5mmID9mm ODfiber washer. Insertoneend of burnerclip intoholeinsidebumertube andhookotherendaroundvalvemanifold.Attachsideburnerignitorwire (C). Presssideburnercontrolknobontovalvestem andsideburnergrateontoshelf(D). Attachhingesto backofshelfwith#10-24xl/2"screw
