ページ1に含まれる内容の要旨
Owner's Manual
i T
®
Liquid Propane Gas Grill
Model141.16691
Natural Gas Grill
Model141.17691
A WARNING: Note to Installer: Leave this Owner's Manual
withthe consumer after delivery and/or installation.
Read this Owner's Manual carefully and be sure
your gas grill is properly assembled, installed and
Note to Consumer: Leave this Owner's Manual
maintained. Failure to follow these instructions
in a convenient place for future reference.
could result in serious bodily injury and/or property
damage.
ページ2に含まれる内容の要旨
Z_WARNING Warranty ..................................................... 2 Combustion byproducts produced when using Safety Instructions ..................................... 2 this product contain chemicals known to the State of California to cause cancer, birth Hardware .................................................... 6 defects, or other reproductive harm. Parts Diagram and Lists ........................ 7 Z_WARNING Assembly Instructions .............................. 10 Failure to comply
ページ3に含まれる内容の要旨
Correct LP Gas Tank Use • LP gas tanks must be stored outdoors in a LP gas grill models are designed for use with a well-ventilated area and out of the reach of standard 20 lb. Liquid Propane Gas (LP gas) tank, children. Disconnected LP gas tanks must not not included in grill box. Never connect your gas be stored in a building, garage or any other _ritl to an LP gas tank that exceeds this capacity. enclosed area. tank of approximately 12 inches in diameter by 18-1/2 inches high is the maximum s
ページ4に含まれる内容の要旨
Figure 1 (Naturalgas model only) IMPORTANT: your Kenmore Natural Gas Grill cannot GAS SUPPLY be converted to use LP Gas. Attempting to do so INSIDE is extremely hazardous and will also void the grill WALL warranty. OUTSIDE WALL Your natural gas grill is designed to operate on TO GRILL natural gas only, at a pressure of 7" water column SHUT OFF (W.C.) (1/4 psi or 1.75 kpa), regulated at the LOCKING SHUT OFF residential meter. Check with your gas utility \ \ company for local gas pressure and with
ページ5に含まれる内容の要旨
CAUTION:Spidersand smallinsectsocca- To reduce the chance of "FLASHBACK" (see sionallyspin websor makenestsin the grill CAUTION at left) clean the Burner Tubes and BurnerTubesduringtransitand warehousing. Burners before fully assembling your grill. Thesewebscanleadto a gasflowobstruc- Remove the Cotter Pin from the rear underside tionwhichcouldresultin a fire in and around of each Burner using a pair of long nose pliers. the BurnerTubes.Thistype of fire is known Carefully lift each Burner up and
ページ6に含まれる内容の要旨
Thefollowingtableillustratesa breakdown of the hardware pack.It highlights whatcomponents are used in the variousstagesof assembly. Ref. Component Qty. Purpose of Components Attaches Side Shelf To Grill Head $122G04121 Phillips Head Screw 1/4"x3/4" 4 Attaches Cart Side Handle To Grill Head $142G04121 Countersink Flat Head Screw 1/4"x3/4" 4 Powers The Electric Ignitor P05301001A AA Battery 2 Powers The Fuel Gauge Display (LPG model only) P05301003A 9V Battery 1 Size and Quantity of each Hardware
ページ7に含まれる内容の要旨
LPG = Liquid Propane Gas NG = Natural Gas 30b\ 38 23_ 18 24 28 36 Ib 3_ 31 _(LPG only144 32 / 37 16 64 (LPG only) |i (LPG only)40 65_ (NG only)41 ] _43 (LP¢ only)71 (NG only)72 __7_ (LPG only) _59 57 bl 7
ページ8に含まれる内容の要旨
PEP# DESCRIPTION PART# QTY 1 Lid 1 P0011903AA 2 Lid Trim Plate 1 P0011435EA 3 Temperature Gauge 1 P00601171A 4 Lid Handle 1 P00205033B 5 Name Plate 1 P00410038C 6 Cooking Rack/Secondary 1 P01518001B 3 7 Cooking Grid/Large P01606032B 1 8 Cooking Grid/Small P01606033B 3 9 Flame Tamer/Large P01708031B 10 Flame Tamer/Small 1 P01708032B 11 Burner/Main 6 P02001004E 1la Burner Air Shutter/Main (NG only) 6 P05524004A 12 Burner Bracket 1 P02206271B 13 Gas Collector Box with Electrode 3 P02608050C 14 Elec
ページ9に含まれる内容の要旨
FIEF# DESCRIPTION PART# QTY 49 Door Trim Plate, Left P07506007A 1 50 Door Trim Plate, Right (LPG) P07507007A 1 51 Door Trim Plate, Right (NG) P07507008A 1 52 Cart Partition Panel P07512013A 1 53 Cart Decorative Panel P07501008A 1 54 Cart Decorative Panel, Trim Plate P07509009A 1 55 Door Hinge Bracket, UppedLeft P03314018C 1 56 Door Hinge Bracket, Lower/Left P03314019C 1 57 Door Hinge Bracket, UppedRight P03314020C 1 58 Door Hinge Bracket, Lower/Right P03314021C 1 59 Door Magnet PO5523002K 4 60 D
ページ10に含まれる内容の要旨
Figure 1 CAUTION : While it is possible for one person to assemble this grill, obtain assistance from another person when handling some of the larger, heavier pieces. 1. Open the parts boxes. Use the parts list to check that all parts have been included. -..Ai 2. Inspect the grill fordamage as you assemble it. Do LEFT OUTSIDE not assemble or operate the gdlt if it appears BOWL PANEL damaged. If there are damaged or missing parts when you unpack the shipping box, or you have questions dudng the a
ページ11に含まれる内容の要旨
Installing Cooking Components Electrode Check - Requires an Assistant Before placing the cooking components into your Important: Before cooking on your grill the first grill, ensure that the Spark Electrode Tip is properly time, wash the Cooking Grids and Cooking Rack positioned within each Gas Collector Box ( a 4" with warm, soapy water. Rinse and dry thoroughly. wide stainless mechanism found at the front be- After cooking is completed, turn grill to HIGH tween each set of Burners.) The easies
ページ12に含まれる内容の要旨
FOR LP GRILLS ONLY Figure 6a Battery Replacement: FUEL GAUGE 1. Remove the Grease Trayfrom the griE DISPLAY COVER 2. Stretch your hand behind Control Panel and unscrewthe Battery Cover behind the Display Box. 3. Pult out the Battery with electric wire from the Battery 9V BATTERY Compartment. 4. Replace the used Batterywiththenewone. J BATTERY CONNECTOR 5. Replace the new Battery with electric wire back into IMPORTANT: When the gas tank is removed from Battery Compartment. See Figure 6a. the tank
ページ13に含まれる内容の要旨
Connecting A Liquid Propane Gas (LPgas) Figure 7a (LP gas model only) Tank To Your Grill 1. Remove the Pull-out Grease Draining Trayw_th the Heat Shieldfrom Grill. 2. Locate hose and regulator assure bly packed for shipping purposes on front underside of grill head. Remove fastening band. Push assembly to back of grill and pull down to connect to tank valve. Before connecting, check valve and assembly threads to be sure they match. (Type 1 connection per ANSI Z21.58b-2002). See Figure 7b. 3. Ins
ページ14に含まれる内容の要旨
Connecting Natural Gas To Your Grill For Natural Gas grills: The 12 foot Natural Gas Hose has already been connected to the Gas Manifold as shown in Figure 7c. Thread the 12 foot Natural Gas Hose through the hole of Rear Panel to outside. Also read the natural gas safety instructions,(on page 4) Figure 7c (Natural gas model only) GAS MANIFOLD REAR PANEL \ j 12' NATURAL J GAS HOSE HOLE FOR _12' NATURAL GAS HOSE Install Pull-out Grease Tray Place Heat Shield into Putl-out Grease Draining Tray. The
ページ15に含まれる内容の要旨
LP Tank Exchange WARNING • Many retailers that sell grills offer you the op- tion of replacing your empty LP tank through an exchange service. Use onty those reputable If you smell gas: exchange companies that inspect, precision fill, test and certify their cylinders. Exchange • Shut off gas supply to the gas grill. your tank only for an OPD safety feature-equipped • Turn the Control Knobs to OFF position. tank as described in the LP Tank section of • Extinguish any open flame such as candle, th
ページ16に含まれる内容の要旨
8_ If the burner does not light, turn the Control Knob to OFF, wait 5 minutes for gas to clear, then retry. BasicLighting Procedures 9. Once the left grill burner is ignited, the adjacent Machine oils used in the manufacturing process of burner can be lit by simply turning its Control Knob stainless steel can cause stainless steel to turn a tan toHIGH. color Before initial grill use, remove protective PVC film from Control Panel and inside and outside of Grill 10. Adjust ControI Knobstoyourdesir
ページ17に含まれる内容の要旨
Manually Lighting Your Grill by Match Misalignment of Ignitoron Burner Correction: Check for proper position of the To light your main burners by match, Follow steps 1 Electrode Tip as shown in Figure 4 The gap through 6 of the Gas Lighting Instructions. Then light between the Spark Electrode Tip and Burner or the match and place it over the top oppening of the Spark Receiver should be approximately3/16", Lighting Tube. Push and turn the nearest Control Knob Adjust if necessary. With the gas sup
ページ18に含まれる内容の要旨
5. Cover each Gas Valve Orificewith aluminum foil. 6. Brush the inside and bottom of the grill with a fiber CAUTION: pad or nylon brush, and wash with a mild soap and BesureyourgrillisOFFandcoolbeforecleaning. warm water solution. Rinse thoroughly and let dry. Takecarenottochiporscratch thepainted surfaces 7. Remove aluminum foil from Orificesand check because itwillvoidyourwarranty against rusting. each Orifice for obstruction. Aswithallappliances, proper careandmaintenance 8. Check each Spark
ページ19に含まれる内容の要旨
Cleaning The Burner Tubes and Burner Ports Regardtessof which Burner cteaning procedure you use, we recommend you also complete the following To reduce the chance of FLASHBACK the procedure steps to help prolong Burner life. below should be followed at least once a month in late 1. Use a fiber pad or nylon brush to clean the entire summer or early fall when spiders are most active or outer surface of each Burner until free of food when your grill has not been used for a period of time. residue a
ページ20に含まれる内容の要旨
Question: What is the best way to protect my new Kenmora gas grill from the weather? Answer: A good quality grill cover should be used to Question: Can I convert my Kenmore gas grill from protect your grill when not in use. Sears offers a cover one fuel type to another? that is made to fit this particular grill model. Also, follow Answer: Your Kenmore gas grill is manufactured to the cleaning and maintenance instructions in this exact specifications and isapproved by the Canadian Owner's Manual
