ページ1に含まれる内容の要旨
USERS GUIDE EAGLE HM
We open up New Horizons
MOTION SENSOR
The High Mounting Eagle Motion Detector (PN: 10EAGLE1HM) nd technology combined with digital processing to assure a
DESCRIPTION
sharp, stable activation pattern with outstanding adjustability. Some of the adjustments include unidirectional sensing
capabilities, 3-dimensional angle adjustment, and heightened immunity to highly sensitive motion settings. These
adjustments can be made with BEA’s universal rem
ページ2に含まれる内容の要旨
SAFETY • Shut off all power going to the header before attempting any wiring procedures. PRECAUTIONS • Maintain a clean & safe environment when working in public areas. • Constantly be aware of pedestrian traffic around the door area. • Always stop pedestrian traffic through the doorway when performing tests that may result in unexpected reactions by the door. • Always check placement of all wiring and components before powering up to insure that moving door parts will not catch an
ページ3に含まれる内容の要旨
MECHANICAL A. WIDTH OF THE SENSING FIELD ADJUSTMENTS - SETTING THE The antenna for the Eagle HM is identified by it’s 9 elements. There is no narrow or wide antenna. Only the 9 element antenna is utilized for the Eagle HM. SENSING FIELD DIMENSIONS B. THE POSITION OF THE SENSING FIELD IS DETERMINED BY THE VERTICAL TILT ANGLE OF THE ANTENNA A B C 27º 20º 0º To obtain a sensing field as close to the door as possible : the tilt angle of the antenna mus
ページ4に含まれる内容の要旨
MECHANICAL ADJUSTMENTS - SETTING THE SENSING FIELD DIMENSIONS – 70º Cont. For ceiling mounting, the vertical tilt angle of the antenna must be set at the maximum position of 70-75° and the spherical part of the sensor must be oriented in the opposite direction to the door. C. THE LATERAL POSITION OF THE SENSING FIELD IN FRONT OF THE DOOR IS DETERMINED BY THE LATERAL TILT ANGLE OF THE ANTENNA. 6.4’ 3.2’ 0
ページ5に含まれる内容の要旨
1. The Eagle SMR is fully compatible with BEA’s Remote Control as shown below. Use of the remote control should be BEA’s REMOTE conducted within 10’ – 15’ of the sensor, and the remote should be pointed directly at the sensor when used. Refer to the “Programming Guide” in the following section for each parameter and it’s values. CONTROL Not Used Number Keys Not Used Plus + Lock Unlock Minus – Check Values Sensitivity Not Used Relay Hold Time Relay
ページ6に含まれる内容の要旨
KEY USER’S ACTIONS DEFAULT LED STATUS PROGRAMMING GUIDE Cont. Press the UNLOCK key once, then enter 0000 The red LED will flash quickly after UNLOCK UNLOCKING & your 4-digit code to unlock the Eagle. UNLOCK is pressed once. After LOCKING entering the valid code, Eagle will flash red LED slowly. 0-9 0-9 0-9 0-9 If access code is set to the factory default value of 0000, the Eagle will
ページ7に含まれる内容の要旨
KEY USER’S ACTIONS DEFAULT LED STATUS PROGRAMMING GUIDE Cont. DETECTION MODE Detection mode offers 3 different levels of 3 After pressing the DETECTION MODE detection: Bi-directional, Uni-directional and key, the red LED flashes quickly. After Uni-directional with MTF (motion tracking pressing a number button, the red LED feature). MTF allows the Eagle to switch flashes slowly. from uni-dire
ページ8に含まれる内容の要旨
OTHER ACCESSORIES PN: 10ECA PN: 10EMB PN: 10ERA For mounting into the ceiling, use Bracket for mounting on the Rain protection accessory. the ECA embedding accessory. top of the door header. If after troubleshooting a problem, a satisfactory solution cannot be achieved, please call B.E.A., Inc. COMPANY for further assistance during Eastern Standard Time at 1-800-523-2462 from 8am - 5pm. CONTACT For after-hours, call East Coast: 1-866-
