ページ1に含まれる内容の要旨
Supervised Security System
Owner's Guide
1
15
3 RECORD Install
Run 1
13 5
Run 2
11 7 ARM
9
UNIT
A
BYPASS
O C
M E
K G
I
HOUSE
AC Power
Battery Low
zones
1
2
3
1 2 3
4
5
4 5 6
6
7 8 9 7
8
PROG 0 MEM
REC/BUSY ARMED
Supervised Security System DS7000
•
• •
•
• •
•
•
• •
• •
• •
•
ページ2に含まれる内容の要旨
If more than one telephone or other device is Contents READ THIS FIRST connected to the same line, add up all the Introduction ................................................................................................... 4 RENs. If the total is more than five, the This equipment generates and uses radio telephones might not ring. In rural areas, a total frequency energy, and if not installed and used Installation .............................................................................
ページ3に含まれる内容の要旨
Introduction Installation The X10 Supervised Security System is built around a Security Console with an Locating Security System components automatic dialer that calls neighbors or friends in the event of a break in. Battery powered RF Door/Window Sensors and Motion Detectors are used to trigger the alarm, with RF Handheld and Keychain Remote controls for arming and disarming. All sensors and remotes incorporate random digital security coding. The system may be configured with any combination of
ページ4に含まれる内容の要旨
Installation Installation Security Console Security Remote Mounting the console PANIC PANIC The Security Console is designed to be installed free-standing on a table top or shelf. ARM DIS- HOME ARM A wall mounting bracket is also available. ARM DIS- AWAY ARM Fitting the backup battery SECURITY LIGHT Slide off the battery compartment cover and clip a 9V battery onto the battery contacts. ON OFF Slide the battery into the battery compartment and re
ページ5に含まれる内容の要旨
Installation Installation Keychain Remote Door/Window Sensor BATTERY DOOR/WINDOW SENSOR ARM PANIC DELAY MAX MIN DISARM DOOR/WINDOW SENSOR Ideal location TEST LIGHTS ON Two windows (requires LIGHTS accessory magnetic OFF switch pair) DOOR/WINDOW SENSOR Sliding window Registering the Keychain Remote with the Security Console Installing the Door/Window Sensor • Fit two AAA Alkaline batteries in the battery compartment in the back of the Keychain • Attach the Door/Window Sensor to the wall using the
ページ6に含まれる内容の要旨
Installation Installation Testing the Motion Detector Motion Detector • Set the slide switch on the Motion Detector to position 1. • Press and hold the TEST button for about a second. The LED flashes twice when you release it. 90˚ • Wait 20 seconds for the sensor to settle. • Walk in front of the Motion Detector. The indicator LED lights each time it senses movement. Check the coverage area and reposition the sensor as required. • Press the TEST button to return to normal operating mode. 5-6ft N
ページ7に含まれる内容の要旨
Installation Installation ™ Power Horn Remote Siren (sold separately) Lamp Module 1 15 3 1 15 3 13 5 13 5 11 7 9 11 7 UNIT 9 UNIT A O C A O C M E M E K G I K G HOUSE I HOUSE Power Horn Lamp Module Installing the Power Horn Installing the Lamp Module to control the security light • Set the House Code dial to the same House Code as the Security System • Set the House Code and Unit Code dials to match the settings on the Security • Set the Unit Code dial to an unused code. Console. This allows it t
ページ8に含まれる内容の要旨
Installation Setting up the Dialer Other X10 products (sold separately) Programming Phone Numbers Note: you should program the console to call a friend, relative or neighbor who can then ON OFF listen-in to your home to determine if there is a real problem. The person can then call A O C the Police if necessary, or call you back to see if everything is fine. You should NOT M E K G I program the console to dial the Police directly. 1 A 1 15 3 13 5 M E 13 1. Set the console to INSTALL. 5 9 I 11 7
ページ9に含まれる内容の要旨
Using the Security System Using the Security System INSTANT Mode Console Zone Indicators Note: The Key Chain Remote always arms the system in the INSTANT mode. The console displays the status of the first eight zones. These indicators can display four 1. If using the Handheld Remote, set its Delay switch to MIN. states, as follows: 2. Press ARM. The Console emits two tones and the ARMED indicator turns on. Steady on - means that particular door or window is open. Open a door or window, the alarm
ページ10に含まれる内容の要旨
Battery Information Battery Information Door/Window Sensors and Motion Detectors General X10 Door/Window Sensors, Motion Detectors and Security and Keychain remotes are Battery Replacement designed to operate for approximately two years when fitted with alkaline batteries. If any if the Console's zone indicators flash slowly, the Motion Detector or Door/Window Since operating conditions vary from installation to installation however, it is recom- Sensor for that zone has not reported in during t
ページ11に含まれる内容の要旨
Troubleshooting Troubleshooting PROBLEM SOLUTION PROBLEM SOLUTION If the system does not arm. • Check that the Console's slide switch If you hear a repetitive trouble alarm Check the zone indicators. If a door or is set to RUN1 or RUN2. when you try to arm the system, and it window is open, its zone indicator is on. • Check that the battery indicator on the does not arm. If there is a problem with a Sensor or Remote turns on when you press Motion Detector, its zone indicator ARM. Replace the bat
ページ12に含まれる内容の要旨
Troubleshooting Troubleshooting PROBLEM SOLUTION PROBLEM SOLUTION You open a door or window and the If you do not hear a beep from the With the Console in the RUN 2 mode, • Check that the system is armed. Console when you press TEST to install alarm does not trip. check that it chimes when you press • Check that the console's slide switch a Door/Window Sensor or Motion TEST on the sensor/motion detector. If it is set to RUN1 or RUN2. Detector. does, then the sensor/motion detector is already ins
ページ13に含まれる内容の要旨
Troubleshooting Troubleshooting Special Notes PROBLEM SOLUTION Intercom Systems If the armed indicator is flashing. This indicates that there has been an intrusion. Also, if a zone indicator is on, Intercom systems which send voice signals over existing electrical wiring may interfere Troubleshooting this indicates which zone was violated. To with the ability to control modules from your X10 security system with the intercom in turn the zone indicator off, and stop the use. If the intercom syste
ページ14に含まれる内容の要旨
Warranty Notes ONE YEAR LIMITED WARRANTY X10 (USA) INC. (X10) WARRANTS ITS PRODUCTS TO BE FREE FROM DEFECTIVE MATERIAL AND WORKMANSHIP FOR A PERIOD OF ONE (1) YEAR FROM THE ORIGINAL DATE OF PURCHASE AT RETAIL. X10 AGREES TO REPAIR OR REPLACE, AT ITS SOLE DISCRETION, A DEFECTIVE X10 PRODUCT IF RETURNED TO X10 WITHIN THE WARRANTY PERIOD AND WITH PROOF OF PURCHASE. IF SERVICE IS REQUIRED UNDER THIS WARRANTY: 1. RETURN THE DEFECTIVE UNIT POSTAGE PREPAID TO: X10 (USA) INC., 91 RUCKMAN RD., CLOSTER, N
ページ15に含まれる内容の要旨
X10 (USA) INC., 91 RUCKMAN RD., CLOSTER, NJ 07624 WWW.X10.COM DS7000 -4/99DR Supervised Security System
