ページ1に含まれる内容の要旨
Indoor/Outdoor Color Camera
with Built-in 2.4 GHz Wireless
Video Sender, and separate
Video Receiver
OWNER'S MANUAL
MODEL VK45A
(INCLUDES XC10A CAMERA, VR30A VIDEO RECEIVER
AND PLUG-IN POWER SUPPLIES)
ページ2に含まれる内容の要旨
INTRODUCTION IMPORTANT SAFETY INSTRUCTIONS Your Wireless Camera Kit consists of a Color Video Camera with 1. Read Instructions - All the safety and operating instructions should be read built-in 2..4 GHz Video Sender, and a Video Receiver unit which you before the product is operated. connect to a TV anywhere in your home (up to 100 ft. away from the 2. Retain Instructions - The safety and operating instructions should be retained for Camera). The Camera/Video Sender converts the video and aud
ページ3に含まれる内容の要旨
11. Power Sources - This product should be operated only from the type of power c) If the product has been exposed to rain or water, source indicated on the marking label. If you are not sure of the type or power d) If the product does not operate normally by following the operating instructions. supply to your home, consult your product dealer or local power company. For Adjust only those controls that are covered by the operating instructions as an products intended to operate from battery pow
ページ4に含まれる内容の要旨
CONTENTS CONTROLS AND CONNECTIONS CONTROLS AND CONNECTIONS ........................................ 7 AMERA/VIDEO SENDER, AND VIDEO RECEIVER .................... 7 C CAMERA/VIDEO SENDER .................................................. 8 CAMERA/VIDEO VIDEO RECEIVER SENDER (BOTTOM VIEW) VIDEO RECEIVER............................................................. 9 TV CONNECTING UP........................................................... 10 Channel 2.4 GHz SETTING UP THE CAMERA/VIDEO SENDER.....
ページ5に含まれる内容の要旨
CONTROLS AND CONNECTIONS CAMERA/VIDEO SENDER VIDEO RECEIVER 2.4 GHz Video Antenna 2.4 GHz Video Antenna Set channel switch to match setting on Video Receiver. TV Output Connector Mounting plate ON-OFF Switch (on side) Power Supply Jack TV Channel 2.4 GHz Channel A/V Input Switch Switch Jacks Cable adapter. (on bottom) (on bottom) 8 9
ページ6に含まれる内容の要旨
CONNECTING UP SETTING UP THE CAMERA/VIDEO SENDER Referring to the diagram on the next page: 2.4 GHz Video Set channel switch to Antenna match setting on 1. Attach the camera to a wall using the screws provided. Video Receiver. 2. If you install the camera outdoors, make a small hole in your exterior wall and pass the low voltage power jack through it. 3. Plug the power supply jack into the socket on the adapter cable from the camera. Use the smaller of the two power supplies. Attach camera to a
ページ7に含まれる内容の要旨
HOOKING UP THE VIDEO RECEIVER IF YOUR TV IS ALREADY HOOKED UP TO A DSS RECEIVER OR OTHER A/V DEVICE If a DSS Receiver or other A/V 1. Connect a set of Audio/Video cables component is connected to the TV using to the A/V OUT jacks of your Video A/V cables, you can connect the Video Receiver. Connect the other end to Receiver to the free LINE IN jacks on your TV. the component. If there are no LINE IN jacks, you will need to use a TV 2. Plug the Video Receiver's Power Supply (the larger of the two
ページ8に含まれる内容の要旨
FINE TUNING YOUR SYSTEM WARRANTY 12 MONTH LIMITED WARRANTY The Wireless Video Sender usually works best with the flat faces of the antennas on the Sender and Receiver unit facing each other (i.e. X10 (USA) INC. (X10) WARRANTS ITS PRODUCTS TO BE FREE FROM in “Line of sight” - see diagram below). Sometimes, however, DEFECTIVE MATERIAL AND WORKMANSHIP FOR A PERIOD OF ONE (1) reflections and other effects in the home may affect the signal so that YEAR FROM THE ORIGINAL DATE OF PURCHASE AT RETAIL. X
ページ9に含まれる内容の要旨
X10 (USA) Inc. 3824 North 5th St., Suite C, North Las Vegas, NV 89030 Web Site: www.x10.com VK45A-11/99 16
