ページ1に含まれる内容の要旨
1” EARTHQUAKE
IMPACT WRENCH
Model 92421
ASSEMBLY and OPERATING
INSTRUCTIONS
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at http://www.harborfreight.com
TO PREVENT SERIOUS INJURY,
READ AND UNDERSTAND ALL WARNINGS
AND INSTRUCTIONS BEFORE USE.
© ®
Copyright 2005 by Harbor Freight Tools . All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For techni
ページ2に含まれる内容の要旨
Specifications Maximum Torque 1800 Ft. Lbs. Drive Size 1” Air Inlet 1/2”-14 NPT Recommended Air Pressure 90 PSI Average Air Consumption 8 CFM Tool Weight 24.6 Lbs. Impact Mechanism Twin Hammer Save This Manual You will need the manual for the safety warnings and precautions, assembly instructions, operating and maintenance procedures, parts list and diagram. Keep your invoice with this manual. Write the invoice number on the inside of the front cover. Keep the manual and invoice in a safe and
ページ3に含まれる内容の要旨
7. Use eye and ear protection. Always wear ANSI approved impact safety goggles. Wear a full face shield if you are producing metal filings or wood chips. Wear an ANSI approved dust mask or respirator when working around metal, wood, and chemical dusts and mists. 8. Do not overreach. Keep proper footing and balance at all times. Do not reach over or across running machines or air hoses. 9. Maintain tools with care. Keep tools clean for better and safer performance. Follow instructions for lubr
ページ4に含まれる内容の要旨
20. Compressed air only. Never use combustible gas as a power source. 21. This Impact Wrench should only be used with impact rated sockets and extensions. Using any other accessories can cause the accessories to break, causing permanent damage to the unit and severe injury to the operator. Note: Performance of the compressor (if powered by line voltage) may vary depending on variations in local line voltage. Extension cord usage may also affect tool performance. Warning: The warnings, cautions
ページ5に含まれる内容の要旨
Assembly Place the Handle (45) onto the side of the Hammer Case (43) and secure it with four Screws (46) and Washers (46A). See FIGURE 1. FIGURE 1 Securing with Screws (46) and Washers (46A) (Hex Wrench not included) Operation Warning!! This Impact Wrench supplies powerful torque and is designed to be operated with two hands. Failure to operate the Impact Wrench with two hands may result in serious, per- manent injury. See FIGURE 3 below. Trigger (13) FIGURE 2 Anvil (38) Screw (46) and Washer
ページ6に含まれる内容の要旨
Operation (continued) Refer to FIGURES 2 and 3 on page 5, and the Assembly Drawing on page 9. Note: Turn off your air compressor and disconnect the air hose when you are changing sockets. After you attach the socket, attach the air hose and turn the air compressor on. 1. Select the appropriate size 1” drive socket for your needs. 2. Push and snap the socket (not included) onto the Anvil (38). 3. To operate the Forward/Reverse Valve (17) follow the directions in FIGURE 4 below. FIGURE 4 Forward
ページ7に含まれる内容の要旨
Operation (continued) Loosening Note: Set the Forward/Reverse Valve (17) so that the anvil turns counterclockwise (reverse). 12. Place the socket (not included) over the nut you wish to loosen. 13. Grip the Impact Wrench firmly with two hands and gently squeeze the Trigger (13). Note: If the Impact Wrench cannot loosen the nut, do not raise the air pressure on the compressor over 90 PSI. Do not attempt to loosen the nut with the Impact Wrench. Use other appropriate methods and tools to loosen t
ページ8に含まれる内容の要旨
Parts List Part No. Description Qty. Part No. Description Qty. 1 Trigger Handle 1 28 Cylinder 1 2 Throttle Valve Bushing 1 29 Pin 1 2A Throttle Valve Seat 1 29A Pin 1 3 Throttle Valve Plunger 1 30 Front End Plate 1 4 Throttle Valve 1 31 Front End Bearing 1 5 Throttle Valve Spring 1 32 End Plate Gasket 1 6 0-ring 1 33 Motor Housing 1 10B Air Inlet 1 34 Bearing 1 11 Rubber Cap 1 35 Hammer Pin 2 12 Trigger Pin 2 36 Hammer Frame 1 13 Trigger 1 37 Hammer 2 14 Pin 1 38 Anvil 1 15 F/R Valve Bushing 1 4
ページ9に含まれる内容の要旨
Assembly Drawing SKU 92421 For technical questions, please call 1-800-444-3353 Page 9
