ページ18に含まれる内容の要旨
13-4940-00251 Commend SIP Doorphone Figure 7 – Commend SIP Doorphone 14
ページ19に含まれる内容の要旨
13-4940-00251 Commend SIP Doorphone Figure 8 – Initial Configuration
ページ20に含まれる内容の要旨
13-4940-00251 Commend SIP Doorphone Figure 9 – Initial Configuration 16
ページ1に含まれる内容の要旨
MITEL – SIPCoE
Technical
Configuration Notes
Configure the MCD 6.0 for use
with the Commend SIP
Doorphone
SIP CoE 13-4940-00251
ページ2に含まれる内容の要旨
NOTICE The information contained in this document is believed to be accurate in all respects but ® is not warranted by Mitel Networks™ Corporation (MITEL ). The information is subject to change without notice and should not be construed in any way as a commitment by Mitel or any of its affiliates or subsidiaries. Mitel and its affiliates and subsidiaries assume no responsibility for any errors or omissions in this document. Revisions of this document or new editions of it may be issued
ページ3に含まれる内容の要旨
Table of Contents OVERVIEW ............................................................................................................... 1 Interop History....................................................................................................................1 Interop Status ....................................................................................................................1 Software & Hardware Setup ............................................................
ページ4に含まれる内容の要旨
ページ5に含まれる内容の要旨
13-4940-00251 Commend SIP Doorphone Overview This document provides a reference to Mitel Authorized Solutions Providers for configuring the Mitel 3300 ICP to host the Commend SIP Doorphone. The different devices can be configured in various configurations depending on your VoIP solution. This document covers a basic setup with required option setup. Interop History Version Date Reason 1 February 27,
ページ6に含まれる内容の要旨
13-4940-00251 Commend SIP Doorphone Tested Features This is an overview of the features tested during the Interop test cycle and not a detailed view of the test cases. Please see the SIP Line Side Interoperability Test Pans for detailed test cases. Feature Feature Description Issues Basic Call Making and receiving a call DTMF Signal Sending DTMF after call setup (i.e. mailbox password) Call Hold
ページ7に含まれる内容の要旨
13-4940-00251 Commend SIP Doorphone Resiliency The following table lists the scenarios of resilience supported by this device when connected to the MCD 6.0 on the 3300 ICP. Device Scenario 1 Scenario 2 Scenario 3 Scenario 4 Not Supported Not Supported Not Supported Commend doorphone - No issues found - Issues found, cannot recommend use - Issues found Note: Refer to list of device limitations
ページ8に含まれる内容の要旨
13-4940-00251 Commend SIP Doorphone Device Limitations This is a list of problems or not supported features when the Commend SIP Doorphone is connected to the Mitel 3300 ICP. Feature Problem Description De-registration Not supported. The Commend SIP Doorphone has no means on the client to de-register. Recommendation: Contact your local Commend reseller for further details All Call Features The Comm
ページ9に含まれる内容の要旨
13-4940-00251 Commend SIP Doorphone Network Topology This diagram shows how the testing network is configured for reference.
ページ10に含まれる内容の要旨
13-4940-00251 Commend SIP Doorphone Configuration Notes This section is a description of how the SIP Interop was configured. These notes should give a guideline as to how a device can be configured in a customer environment and how the Commend doorphone was configured in our test environment. We recommend that the Commend doorphone is configured in Device Based mode. You will configure the Device Based m
ページ11に含まれる内容の要旨
13-4940-00251 Commend SIP Doorphone Licensing and Option Selection – SIP Licensing Ensure that the 3300 ICP is equipped with enough IP Users licenses for the connection of SIP end points. This can be verified within the License and Option Selection form. See Figure 1. Figure 1 – License and Option Selection
ページ12に含まれる内容の要旨
13-4940-00251 Commend SIP Doorphone Multiline IP Set Configuration On the Mitel 3300 ICP, a SIP device can be programmed either in the User Configuration form or the Multiline IP Set Configuration form and are programmed as a “Generic SIP Phone”. Enterprise Manager can also be used to provision where this application is installed. The User PIN is the SIP authentication password and the Number is the Dire
ページ13に含まれる内容の要旨
13-4940-00251 Commend SIP Doorphone Class of Service Assignment The Class of Service Options form is used to create or edit the Class of Service and specify its options. Classes of Service, identified by Class of Service numbers, are referenced by the Station Attributes form for the SIP device. Many different options may be required for your site deployment, but the options below are required to be chang
ページ14に含まれる内容の要旨
13-4940-00251 Commend SIP Doorphone SIP Device Capabilities This form provides configuration options that can be applied to various types of SIP devices. The association between the SIP device and the form is similar to how the Class of Service options work. The SIP Device Capabilities number provides a SIP profile that can be applied to particular SIP devices to allow for alternate capabilities as recom
ページ15に含まれる内容の要旨
13-4940-00251 Commend SIP Doorphone Settings for the Timers are important part for the SIP devices configuration. Set Registration Period, Subscription Period and Session Timer according to the site requirements. Ensure that the time periods for Registration and Subscription are matching those configured in Commend doorphone. See an example in Figure 5. The settings on all other tabs of SIP Device Capabi
ページ16に含まれる内容の要旨
13-4940-00251 Commend SIP Doorphone Station Attributes Use the Station Attributes form to assign the previously configured Class of Service and SIP Device Capability number to each of the Commend doorphones in the 3300 ICP. This form utilizes Range Programming. Select the Commend doorphone device number then select Change. Enter the previously configured SIP Device Capability number and Class of Service
ページ17に含まれる内容の要旨
13-4940-00251 Commend SIP Doorphone Commend doorphone Configuration Notes The following steps show how to program the Commend doorphone to interconnect with the 3300ICP. The configuration settings below are the main reference points and by any means could not be considered as the comprehensive configuration instructions. We strongly recommend contacting the phones’ manufacturer Commend International
