ページ1に含まれる内容の要旨
Deutsch
MKE 1
Instructions for use
English
Français
Italiano
Español
Neder-
lands
ページ2に含まれる内容の要旨
ページ3に含まれる内容の要旨
Contents MKE 1 ............................................................................ 2 Features ............................................................................ 2 Delivery includes ............................................................. 2 Treble boost...................................................................... 3 Make-up protection ........................................................ 3 Attachment of the microphone.................................... 4 Attach
ページ4に含まれる内容の要旨
MKE 1 The MKE 1 is a high-quality, sub-miniature, sweat- resistant clip-on condenser microphone. It features excellent sound quality and rugged design. The frequency response curve has been optimized for stage, studio and reporting applications (ENG). The MKE 1 is fitted with a very thin (only 1 mm) yet extremely rugged cable, making this microphone an ideal partner for all live sound applications. Features Sub-miniature microphone High maximum sound pressure level Wide frequency response wit
ページ5に含まれる内容の要旨
Treble boost Your microphone is supplied MZC 1-1 with two different frequency response caps. These caps allow you to adjust the treble response of the microphone (see “Free-field MZC 1-2 frequency response curve” on page 7). In addition, the large frequency response cap attenuates wind noise by approx. 15 dB and provides an extended protection against the ingress of moisture. Slip the cap of your choice onto the microphone until it locks into place. Make-up protection When putting on make-up,
ページ6に含まれる内容の要旨
Attachment of the microphone Depending on the area of application, you can attach the MKE 1 in different ways to either clothing or the body. Attachment to the body Use a suitable means (adhesive tape, hair clip, etc.) to attach the microphone to the hair or the body. For a better hold, use the cable sleeves on the microphone cable. Attachment to clothing Use the MZQ 02 clip to attach the microphone to a lapel, tie, collar, etc. 4
ページ7に含まれる内容の要旨
To fix the cable, snap one of the cable sleeves into the microphone holder and guide the cable through the cable grip . You can rotate the microphone holder in the clip in steps of 90°. Adjust the cable in the cable grip so that no cable loop is formed. For thin cloths (e.g. silk), use the outermost hole where the clip’s contact pressure is the highest. 5
ページ8に含まれる内容の要旨
The MZM 2/MZM 10 magnetic mount set can be used to unobtrusively attach the microphone to clothing. The frictional force between the micro-phone and the fabric is often sufficient to ensure that the microphone is not displaced. For smooth and soft cloths, the neckstrap (included in the delivery) ensures that the microphone is not displaced from its proper position. You can also use the ZH 102 pin mount (“Dracula” clip) to attach the microphone to clothing made of fabric that will not be damaged
ページ9に含まれる内容の要旨
Wind protection The quality of outdoor recordings and close miking can be impaired by wind noise. First of all, use the supplied MZC 1-2 frequency response cap. An increased attenuation of wind noise can be obtained by using the MZW 1 basket windshield and the MZW 02 foam windshield . To begin with, use the MZW1 basket windshield which reduces wind noise by approx. 22 dB. With the additional MZW 02 foam windshield you can reduce wind noise by a further 10 dB. The MZW 1 and MZW 02 ar
ページ10に含まれる内容の要旨
Specifications MKE 1 -4 -4-3 Pick-up pattern omni omni Frequency response 20–20,000 Hz 20–20,000 Hz ± 2.5 dB ± 2.5 dB Sensitivity 5 mV/Pa 5 mV/Pa (free field, no load) ± 2.5 dB ± 2.5 dB (1 kHz) Nominal impedance 1 k 1 k Min. terminating 4.7 k 4.7 k impedance Equivalent noise level 27 dB 27 dB A-weighted (DIN IEC 651) CCIR-weighted 39 dB 39 dB (CCIR 468-1) Max. SPL 142 dB 142 dB Power supply via via SK 5212, SK 5212, SK 5012, SK 5012, SK 250, SK 50, SK 250, SK 50, SK 3063 SK 3063 Connect
ページ11に含まれる内容の要旨
Specifications MKE 1 -5 -5-3 Pick-up pattern omni omni Frequency response 20–20,000 Hz 20–20,000 Hz ± 2.5 dB ± 2.5 dB Sensitivity 5 mV/Pa 5 mV/Pa (free field, no load) ± 2.5 dB ± 2.5 dB (1 kHz) Nominal impedance 1 k 1 k Min. terminating 4.7 k 4.7 k impedance Equivalent noise level 27 dB 27 dB A-weighted (DIN IEC 651) CCIR-weighted 39 dB 39 dB (CCIR 468-1) Max. SPL 142 dB 142 dB Power supply 4.5–15 V 4.5–15 V Connector open ends open ends Color black beige Cable length 3 m 3 m Diameter of
ページ12に含まれる内容の要旨
Connector assignment MKE 1-5/MKE 1-5-3 18 kΩ +UB 1µF core AF Ground shield MKE 1-5 required connection MKE 1-5-3 (amplifier circuit) Accessories and spare parts Item Cat. No. MZC 1-1 cap, small, black 513179 MZC 1-1 cap, small, beige 513198 MZC 1-2 cap, large, black 521701 MZC 1-2 cap, large, beige 513197 MZW 01 basket windshield, black 521724 MZW 01 basket windshield, beige 521726 MZC 1-3 make-up protector 521746 MZW 02 foam windshield, black 076615 MZQ 02 clip, black 076659 MZQ 02 clip
ページ13に含まれる内容の要旨
Manufacturer Declarations Warranty The guarantee period for this Sennheiser product is 24months from the date of purchase. Excluded are accessory items, rechargeable or disposable batteries that are delivered with the product; due to their characteristics these products have a shorter service life that is principally dependent on the individual frequency of use. The guarantee period starts from the date of original end- user purchase. For this reason, we recommend that the sales receipt be reta
ページ14に含まれる内容の要旨
CE Declaration of Conformity This equipment is in compliance with the essential requirements and other relevant provisions of Directive 2004/108/EC. The declaration is available on the internet site at www.sennheiser.com. Before putting the device into operation, please observe the respective country-specific regulations! WEEE Declaration Your Sennheiser product was developed and manufactured with high-quality materials and components which can be recycled and/or reused. This symbol indicates t
ページ15に含まれる内容の要旨
Deutsch English Français Italiano Español Nederlands
ページ16に含まれる内容の要旨
Sennheiser electronic GmbH & Co. KG Am Labor 1, 30900 Wedemark, Germany www.sennheiser.com Printed in Germany Publ. 08/08 520110/A02
