ページ1に含まれる内容の要旨
362XL
SONIC MAXIMIZER
User Guide
and
Reference
Manual
ページ2に含まれる内容の要旨
i
ページ3に含まれる内容の要旨
TABLE OF CONTENTS Important Safeguards ……………………………………………………………………………………………………………i BBE Process Explained ……………………………………………………………………………………………………………1 Product Description ………………………………………………………………………………………………………………2 Applications ………………………………………………………………………………………………………………………2 Controls and Connections ………………………………………………………………………………………………………3 Specifications ………………………………………………………………………………………………………………………4 General Operation ………………………………………………………………………………………………………………4 Service /Warranty / Maintenance …………………
ページ4に含まれる内容の要旨
Product Description The BBE 362XL is a ganged stereo, single rack space device for use in +4dBu balanced line level applications. A single function button switches the BBE process on or off in both channels, which is useful for comparing the processed sound to the unprocessed sound. An LED next to the function button glows green when the BBE process is on and red when the process is off. The Lo Contour control is for adjusting the level of phase corrected low frequencies in the program material.
ページ5に含まれる内容の要旨
FRONT PANEL CONTROLS 1 2 3 4 5 1. CLIP LED: Will illuminate at +14dBu, giving a 6dBu warning of the impending distortion at +16dBu, the actual clip point. 2. LO CONTOUR: Regulates the amount of phase corrected bass frequencies. 3. PROCESS: Regulates the amount of phase corrected treble frequencies. 4. BBE FUNCTION: This push button switch allows for quick comparison of processed with unprocessed sound. When the switch is pushed in, the process is on and the indicator LED is green. When the swi
ページ6に含まれる内容の要旨
Specifications Frequency Response, process mode:……………………………Program controlled bypass mode: ……………………………5Hz to 30kHz Signal to noise ratio (balanced): ……………114dB Process in, 126dB Process out THD: ………………………………………………less than 0.1% at -10dBu input, Process in/out Maximum Input:…………………………………+18dBu (may vary due to control settings) Input Impedance: ………………………………10k Ohms Nominal Input Level: …………………………-10dBu ~ +4dBu Output Impedance: ……………………………600 Ohms Nominal Output Level: …………………………-10dBu ~ +4dBu Ma
ページ7に含まれる内容の要旨
Service We recommend that if at all possible, a BBE 362XL which requires service be sent to our facility in Huntington Beach, California. We request that a “RETURN AUTHORIZATION” be issued by the dealer from whom you purchased the unit. If this is not possible, call BBE Sound, Inc. directly at (714) 897-6766, extension 116 to obtain a “RETURN AUTHORIZATION”. Include a copy of the bill of sale with the unit when it is shipped to BBE Sound, Inc. so that the service can be expedited. As the repair
ページ8に含まれる内容の要旨
LIVE APPLICATION: POWERED MIXER There are a couple of ways to configure the BBE 362XL into a powered mixer. The ideal method would be into “Pre-Amp Out/Power Amp In” section of the console. If your console does not have this option, use the main or channel insert points. 6
ページ9に含まれる内容の要旨
LIVE APPLICATION: NON-POWERED MIXER Connect the BBE 362XL to the output of the mixing console. The output of the BBE will drive either a crossover or a power amplifier directly. 7
ページ10に含まれる内容の要旨
RECORDING The BBE 362XL can be utilized in the recording studio on individual instruments of on groups on instruments to improve the sound quality. MASTERING OR DUBBING Use the BBE 362XL for mastering the recording. Even if the BBE Process has been used on individual tracks, an improvement on the total mix will be noticed. 8
ページ11に含まれる内容の要旨
INDIVIDUAL INSTRUMENTS Use the BBE 362XL in the effects loop or the main output of a guitar preamp. For keyboards, the output of the sub-mixer will be the ideal location. 9
ページ12に含まれる内容の要旨
SOUND CONTRACTORS The BBE 362XL will accept the output level of most sound contractor type mixers. DJ APPLICATION Connect the BBE 362XL into the processor loop of a pre-amplifier/mixer and hear the music come alive! 10
ページ13に含まれる内容の要旨
Calibration Procedure for the BBE 362XL (REV/S/ON 1.1) NOTE: THIS UNIT WAS TESTED AND CALIBRATED AT THE FACTORY. THIS PROCEDURE IS FOR QUALIFIED PERSONNEL ONLY. INITIAL SETTINGS: 1. BBE Process control VR2 and Lo Contour control VR1, threshold control VR3, and release control VR4 to minimum (fully C.C.W.). 2. Power switch on and BBE function switch in, (BBE on position). Note: Since both channels are identical in calibration, only channel A will be outlined. Channel B will be in brackets [ ].
ページ14に含まれる内容の要旨
12 362xl
ページ15に含まれる内容の要旨
13
ページ16に含まれる内容の要旨
F I V E Y E A R • L I E M I 5 5 5 5 5381 Production Drive Huntington Beach, CA 92649 714-897-6766 • FAX 714-896-0736 www.bbesound.com covered by U.S. Patent 4,482,866 and other U.S. and foreign patents pending. BBE is the registered trademark of BBE Sound, Inc. rev. 1 5/99 B T B E D • W A R R A N T Y
