ページ1に含まれる内容の要旨
CONTENTS
1. PRODUCT GENERAL INFORMATION..……………………………………………..….2
1.1. Product Description…………………………………………………………………………………….2
1.2. Product Feature…………………………………………...……………………………………………2
1.3. Product Application………………………………………………………….……………………………..2
2. PRODUCT GENERAL………………………………………………………………….….3
2.1. General Specifications………………………….………………..…………………………..… 3
2.2. LED Indicator………………………………………………………..…………..….………………3
2.3. Interface………………………………………………………….…….………………………..…..3
3. PRODUCT HARDWARE
ページ2に含まれる内容の要旨
WLAN PC Card 1. Product General Information 1.1. Product Description GL242201, the wireless Ethernet adapter for Card bus- compliant notebook PCs, is fully compatible with IEEE 802.11b standard and supporting higher data rate to 22Mbps. Using Direct Sequence spread spectrum technology for immunity from interference, it will automatically fallback to lower data rate in the environment of interference. 22Mbps data rate is designed by the Packet Binary Convolution Code (PBCC) modulat
ページ3に含まれる内容の要旨
2. PRODUCT GENERAL 2.1. General Specifications Standards: IEEE802.11b Compliant PC Card standard Ver 7.0 Data Rate: 22Mbps / 11Mbps / 5.5 Mbps / 2Mbps / 1 Mbps auto fallback Security: 64/128/256 bit Wired Equivalent Privacy (WEP) Dimension: 128 x 54 x 5.0 mm (Non-detachable card) 2.2. LED Indicators Power/Status Unlighted: Power Off Red color LED steady On: Power on RF TX/RX Unlighted: no activity Green color LED blinking: TX/RX ac
ページ4に含まれる内容の要旨
3.1.3 Receiver Sensitivity -80 dBm (Typically @25 ℃+5) ℃ 3.1.4 Antenna Type Antenna Type Built in diversity patch antenna Antenna Gain 2 dBi max. 3.1.5. Typical Operation Range 22Mbps 100M 11Mbps 150M 5.5Mbps 250M 2Mbps 300M 1Mbps 350M 3.2 Hardware Specification 3.2.1 MAC controller TI ACX100 3.2.2 Memory 8Kbit EEPROM 3.2.3 Power Power Voltage 3.3 or 5 Volt
ページ5に含まれる内容の要旨
Link Quality Receiving AP link quality on infrastructure networking mode Signal Strength Receiving AP signal strength on infrastructure networking mode 5. REGULATION COMPLIANCE Compliant with FCC Part 15 Class B and C ETSI EN 300 328-2 and ETSI EN 301 489-1, -17, EN60950, CE-Mark Telec (Japan, Customized) WiFi Compliant 6. Environmental Requirement 6.1. Drop and Vibration 6.1.1. Anti-Static Voltage Static voltage tests by 4 kV in card frame should not cause system fail
ページ6に含まれる内容の要旨
Storage 0% to 95% Non-condensing 7. INSTALLATION AND CONFIGURATION 7.1. Installation 1. Start the computer 2. Insert the PC CARD to the slot of computer 3. Run ”E:\ Wlan PC Card\Utility\Setup.exe”. Windows will automatically start Installshield Wizard and then insert the PC CARD into the slot of the computer. 4. Select “PC Card/PCI Card” 5. Click “Install “ Button. 6. Click “Next” button. 7. Click “Finish” button to restart computer. 7.2. Configuration 1. Please insert you
ページ7に含まれる内容の要旨
4.Click the “Configuration”. The Configuration page will appear. Enter your wireless network’s SSID, select the BSS Type, suggest you use default “Infrastructure”, Then click “Apply”. 5. Click the “Security”. From the security setting screen, you can set the Wired Equivalent Privacy (WEP) encryption by checking the “Data Encryption”. Then change the “Key Format” to “ASC II”. It is easier than using the “HEX” format. Enter a set of random combination of number and alphabet in the “
ページ8に含まれる内容の要旨
If you have an access point and enable the security function, please follow the access point “Network Key”. 6.Click “SiteSurvey”. Select one of SSID from “Available Network” Block. Then click “Connect” button to enter Profile page. 7. You can set all parameters or click “OK” to back to previous page. If you click “OK” directly, then you finish the connect action. 8
ページ9に含まれる内容の要旨
8.Click “About”. It will show you Software Version of this Wireless Lan PC Card. Notice : Our company reserves the right to change specifications detailed in this document at any time without notice, and assumes no responsibility for any errors within this document. 9
ページ10に含まれる内容の要旨
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if t not installed and used in accordance with the instructions, may cause harmful interference to radio commun
