ページ1に含まれる内容の要旨
TM
Excellence in Motion
TM
FORCE
POWER DRIVE
MICROSTEPPING
Operating
Instructions
ページ2に含まれる内容の要旨
Microstepping MForce PowerDrive Product Manual Changelog Date Revision Changes 04/05/2007 R040507 Initial Release The information in this book has been carefully checked and is believed to be accurate; however, no responsibility is assumed for inaccuracies. Intelligent Motion Systems, Inc., reserves the right to make changes without further notice to any products herein to improve reliability, function or design. Intelligent Motion Systems, Inc., does not assume any liability arising out of t
ページ3に含まれる内容の要旨
Table Of Contents Getting Started: Microstepping MForce PowerDrive .................................................................1-1 Before You Begin ....................................................................................................................... 1-1 Tools and Equipment Required ................................................................................................. 1-1 Connecting the Power Supply ...............................................................
ページ4に含まれる内容の要旨
Enable Input .....................................................................................................................19 Clock Inputs .....................................................................................................................20 Optocoupler Reference ................................................................................................................22 Input Connection Examples .......................................................................
ページ5に含まれる内容の要旨
List of Figures Figure GS.1: Minimum Logic and Power Connections ............................................................. 1-1 Part 1: Hardware Reference Figure 1.1.1: Microstepping MForce PowerDrive ...................................................................... 1-5 Figure 1.2.1: MForce PowerDrive Mechanical Specifications ..................................................... 1-8 Figure 1.2.2: P1 — 12-Pin Locking Wire Crimp Pin Configuration ........................................
ページ6に含まれる内容の要旨
Appendices Figure A.1: MD-CC300-000 ....................................................................................................A-3 Figure A.2: MD-CC300-000 Mechanical Specifications ............................................................A-3 Figure A.3: Typical Setup, Adapter and Prototype Development Cable ....................................A-4 Figure A.4: Hardware Update Wizard .......................................................................................A-4 Figure A.5:
ページ7に含まれる内容の要旨
WARNING! The MForce has components Getting Started which are sensitive to Electrostatic Discharge Microstepping MForce PowerDrive (ESD). All handling should be done at an ESD protected workstation. Before You Begin WARNING! Hazardous voltage levels may be The Getting Started Section is designed to help quickly connect and begin using your Microstepping MForce present if using an open PowerDrive. The following examples will help you get a motor turning for the first time and introduc
ページ8に含まれる内容の要旨
Connect Opto Reference and Logic Inputs Using 22 AWG wire, connect the Opto Reference to the desired reference point. The reference will determine whether or not the logic input is sinking or sourcing. If Sinking Inputs are desired, connect the Opto reference to a +5 to +24 VDC Supply. If Sourcing Outputs are desired, the Opto Reference needs to be connected to the Controller Ground. Connect the Step and Direction inputs to the appropriate outputs of your PLC or controller. Connecting the Mot
ページ9に含まれる内容の要旨
TM FORCE POWER DRIVE MICROSTEPPING Part 1: Hardware Reference Section 1.1: Introduction to the Microstepping MForce PowerDrive Section 1.2: Microstepping MForce PowerDrive Detailed Specifications Part 1: Hardware Specifications 1-3
ページ10に含まれる内容の要旨
Page Intentionally Left Blank Microstepping MForce PowerDrive Manual Revision R040507 1-4
ページ11に含まれる内容の要旨
SECTION 1.1 Introduction to the Microstepping MForce PowerDrive The Microstepping MForce Pow- erDrive is a high performance, low cost microstepping driver that delivers unsurpassed smoothness and perfor- mance achieved through IMS’s advanced 2nd generation current control. By applying innovative techniques to con- trol current flow through the motor, resonance is significantly dampened over the entire speed range and audible noise is reduced. Microstepping MForce PowerDrives accept a
ページ12に含まれる内容の要旨
Features and Benefits • High Performance Microstepping Driver • Advanced 2nd Generation Current Control for Exceptional Performance and Smoothness • Single Supply: +12 to +75 VDC • Low Cost • Extremely Compact • High Output Current: Up to 5 Amps RMS, 7 Amps Peak (Per Phase) • 20 Microstep Resolutions up to 51,200 Steps Per Rev Including: Degrees, Metric, Arc Minutes • Optically Isolated Logic Inputs will Accept +5 to +24 VDC Signals, Sourcing or Sinking • Automatic Current Reduction • Config
ページ13に含まれる内容の要旨
SECTION 1.2 Microstepping MForce PowerDrive Detailed Specifications General Specifications Electrical Specifications Input Voltage (+V) Range* +12 to +75 VDC Max Power Supply Current (Per MForce PowerDrive)* 4 Amps Output Current RMS 5 Amps Output Current Peak (Per Phase) 7 Amps * Actual Power Supply Current will depend on Voltage and Load. Table 1.2.1: Electrical Specifications Thermal Specifications Heat Sink Temperature -40°C to +85°C Table 1.2.2: Thermal Specifications I/O Specificatio
ページ14に含まれる内容の要旨
Setup Parameters The following table illustrates the setup parameters. These are easily configured using the IMS SPI Motor Interface configuration utility. An optional Parameter Setup Cable is available and recommended with the first order. Microstepping MForce PowerDrive Setup Parameters Name Function Range Units Default MHC Motor Hold Current 0 to 100 percent 5 MRC Motor Run Current 1 to 100 percent 25 1, 2, 4, 5, 8, 10, 16, 25, 32, 50, µsteps per MSEL Microstep Resolution 64, 100,108, 125,
ページ15に含まれる内容の要旨
Pin Assignment and Description P1 12-Pin Locking Wire Crimp Connector Option - Power, I/O and SPI Communications Pin Assignment - P1 Power, I/O and SPI NEED A CABLE? Connections The following cables and converters are Pin # Function Description available to interface Pin 1 N/C No Connect with P1: Pin 2 N/C No Connect The Signal applied to the Optocoupler Reference will 12-Pin Locking Wire Crimp determine the sinking/ or sourcing configuration of the inputs. PD12-1434-FL3 Pin 3 Opto Refer
ページ16に含まれる内容の要旨
NEED A CABLE? P3 Connector - DC Power, 2-Pin Locking Wire Crimp The following cables Pin Assignment - P3 Power and converters are available to interface 2-Pin Locking Function Description with P3: Wire Crimp Pin 1 +V +12 to +75 VDC, 4 Amps Maximum per MDrive34Plus. 2-Pin Locking Wire Crimp Pin 2 GND Power Supply Return. PD02-3400-FL3 Table 1.2.8: P3 Connector WARNING! Do not Recommended Connector Shell and Pins plug or unplug DC Power with power Shell: Molex P/N 510-67-0200 applied. Pins:
ページ17に含まれる内容の要旨
Options and Accessories Parameter Setup Cable and Adapters The optional 12.0' (3.6m) parameter setup cable part number MD-CC300-000 facilitates communications wiring and is recommended with first order. It connects from the 10-Pin IDC Connector located at P2 to a PC's USB port. If the12-pin pluggable locking wire crimp connector is used at P1, adapter MD-ADP-1723C is required to use the MD-CC300-000. USB to SPI ...............................................................................
ページ18に含まれる内容の要旨
Page Intentionally Left Blank Microstepping MForce PowerDrive Manual Revision R040507 1-12
ページ19に含まれる内容の要旨
TM FORCE MICRO DRIVE MICROSTEPPING Part 2: Interfacing and Configuring Section 2.1: Mounting and Connection Recommendations Section 2.2: Logic Interface and Connection Section 2.3: Connecting SPI Communications Section 2.4: Using the IMS SPI Motor Interface Section 2.5: Using User-Defined SPI Part 2: Interfacing and Configuring 1
ページ20に含まれる内容の要旨
Page Intentionally Left Blank Microstepping MForce PowerDrive Manual Revision R040507 2
