ページ1に含まれる内容の要旨
LevelOne
FCS-1060/WCS-2060
P/T/Z IP Network Camera
User Manual
Ver 1.0.2 - 0609
ページ2に含まれる内容の要旨
Before You Use This Product The use of surveillance devices may be prohibited by law in your country. The Network Camera is not only a high-performance web-ready camera but also can be part of a flexible surveillance system. It is the user’s responsibility to ensure that the operation of such devices is legal before installing this unit for its intended use. It is important to first verify that all contents received are complete according to the list in the "Package Contents" chapter. T
ページ3に含まれる内容の要旨
Table of Contents Before You Use This Product......................................................................... 2 Package Contents...................................................................................... 5 Installation............................................................................................... 6 Hardware installation............................................................................. 6 Software Installation.................................
ページ4に含まれる内容の要旨
Camera Control ................................................................................. 38 Email & FTP ..................................................................................... 40 Email ........................................................................................ 40 FTP.......................................................................................... 40 Motion detection ................................................................................ 42
ページ5に含まれる内容の要旨
Package Contents FCS-1060/WCS-2060 Dipole Antenna (WCS-2060 Only) Power Adapter Mounting kit & pads CD Manual/Utility Quick Installation Guide 5
ページ6に含まれる内容の要旨
Installation In this manual, "User" refers to whoever has access to the Network Camera, and "Administrator" refers to the person who can configure the Network Camera and grant user access to the camera. Hardware installation Connect the power adapter jack to the Network Camera before plugging in to the power socket. This will reduce the risk of accidental electric shock. Please verify that your product package contains all the accessories listed in
ページ7に含まれる内容の要旨
Camera will try WLAN. During the searching and connecting process to the wireless access point or station, the red LED of the Network Camera will flash every second. Until the Network Camera connects to the other wireless device, the red LED will become lighted. Operating in either network mode, the green LED will flash every second as heartbeat to indicate alive. If the red LED is blinking, please check the network connections. To install in Ethernet Make sure the Ethernet is firmly c
ページ8に含まれる内容の要旨
Software Installation In this manual, "User" refers to whoever has access to the Network Camera, and "Administrator" refers to the person who can configure the Network Camera and grant user access to the camera. At the end of the hardware installation, the Administrator must place the product software CD into the CD-ROM drive of the PC running in MS Windows. An auto-run program will pop up (If the program is not on auto-run, go to the root directory of the software CD and click on “auto
ページ9に含まれる内容の要旨
Click on “Install Software” after the window contains changed, click on “Installation Wizard” to run installation program. Upon Installation Wizard’s start up, a searching box will pop up. This program searches for IP Network Camera on the same LAN: After searching, Network Cameras will be located by the Installation Wizard. There may be several entries shown in the window. The Administrator may differentiate the Network Cameras with the MAC address.
ページ10に含まれる内容の要旨
For the MAC address in the “MAC address” field, please check the label on the bottom of the camera. The IP addresses shown in the "Current IP Address" field reflect those on the local network. They may be from the DHCP server. If there is no DHCP server, the camera will try to find a free IP address (this takes from 15 second to 3 minutes, depending on the LAN status). The method of finding IP address is seeking from 192.168.0.99, to 192.168.0.254. If any of the address inside this
ページ11に含まれる内容の要旨
For more detailed usage of the Installation Wizard, please refer to the user manual of the Installation Wizard included in the product CDROM to find the location of the Network Camera. There may be many Network Cameras in the local network. Users can differentiate the Network Cameras with the MAC address. The MAC address is printed on the back of the Network Camera body. Initial Access to the Network Camera Check Network Settings FCS-1060/WCS-2060 IP Network Camera can be connected e
ページ12に含まれる内容の要旨
in the “Troubleshooting” chapter of the Appendix. Add Password to Prevent Unauthorized Access The default Administrator’s password is blank and the Network Camera initially will not ask for any password. The Administrator should immediately implement a new password as a matter of prudent security practice. Once the Administrator’s password is saved, the Network Camera will ask for the user’s name and password before each access. The Administrator can set up a maximum of twenty (20) user
ページ13に含まれる内容の要旨
How to Use Authentication After opening the Web browser and typing in the URL of the Network Camera, a dialogue window pops up to request a username and password. Upon successful authentication, the following figure is displayed. *If the administrator (root user) assigns no password, everybody can access the homepage directly. 13
ページ14に含まれる内容の要旨
Installing plug-in For the initial access to the Network Camera in Windows, the web browser may prompt for permission to install a new plug-in for the Network Camera. Permission request depends on the Internet security settings of the user’s PC or notebook. If the highest security level is set, the computer may prohibit any installation and execution attempt. This plug-in has been registered for certificate and is used to display the video in the browser. Users may click on to proceed.
ページ15に含まれる内容の要旨
Primary user’s capability Main Screen with Camera View The main page layout has three parts: Configuration functions: The camera can be configured using these user interfaces. Camera View: What the camera sees. Pan/Tilt control buttons: These buttons provide a command interface to control the aim of the camera. Click on the configuration link to the left of the image window to enter the configuration page. The Configuration: “Snapshot” The button provides users a fast way to ca
ページ16に含まれる内容の要旨
The camera view provides not only the live video, but also a way to aim the Network Camera to different target. Using mouse to click on the target inside the video will command the Network Camera to aim at the target. View capabilities This feature allows users to open a digital zoom control window to specify the zoom factor for specified area in the camera view. Users can also move the white frame to select the area of the video that she/he wants to view. “Disable digital zoom” Th
ページ17に含まれる内容の要旨
Mute Digital Zoom Play volume Play/Pause Stop “Play” The option will connect to the Network Camera. The button is the same one as “Pause”. “Pause” The option will pause the video, but the connection remains. The button is the same one as “Play”. “Stop” The option will disconnect to the Network Camera. “Play volume” Click on this button can adjust the audio volume. “Mute” Disable audio at client side. The pan/tilt control buttons: The direction buttons are for Left, R
ページ18に含まれる内容の要旨
“Pan” This button commands the camera to pan from the current position to the left-most and then to the right-most position. After panning, the camera returns to the original position. “Patrol” This button commands the camera to patrol between the preset positions on the Patrol List, which can be modified on the “Camera control page”. After one patrol cycle, the camera returns to the original position. “Stop” This stop the “Auto Pan” command or “Auto Patrol” command. 18
ページ19に含まれる内容の要旨
Client settings At the initial access to the “Connection type” page in Windows, the web browser will ask for a new plug-in installation, the plug-in being the Network Camera. This plug-in has been registered for certification and can be used to change the parameters at the client’s site. The user may click on to install the plug-in. If the web browser does not allow the user to complete the installation, check the Internet security to lower the security level or contact your IT or networ
ページ20に含まれる内容の要旨
http:///client.html is the domain name or the original IP address of the Network Camera. 20
