ページ1に含まれる内容の要旨
EM316E3
EM316E3SF
E3 Fiber Modem
Fiber Driver Module
User’s Guide
ページ2に含まれる内容の要旨
Fiber Driver EM316E3 & EM316E3SF Registration Card Your name: Mr./Ms___________________________________________ Organization: ________________________Dept. __________________ Your title at organization:______________________________________ Telephone: ___________________________ Fax:__________________ Organization's full address:____________________________________ __________________________________________________________ Country:___________________________________________________ Date
ページ3に含まれる内容の要旨
Fiber Driver EM316E3 & EM316E3SF EM316E3 EM316E3SF E3 Fiber Modem Fiber Driver Module User’s Guide P/N: 1226006-001, REV_L PAGE 3
ページ4に含まれる内容の要旨
Fiber Driver EM316E3 & EM316E3SF TABLE OF CONTENTS 1 INTRODUCTION 2 HARDWARE INSTALLATION 3 TROUBLESHOOTING 4 TECHNICAL SPECIFICATIONS 5 CONTACT INFORMATION 6 GLOSSARY 7 ORDERING INFORMATION P/N: 1226006-001, REV_L PAGE 4
ページ5に含まれる内容の要旨
Fiber Driver EM316E3 & EM316E3SF 1 INTRODUCTION About this Manual Before unpacking please refer to section 2 (Hardware Installation) This manual is a guide to the installation and operation of the EM316E3 Fiber modem. Product description describes the product, its functions, features, protocol supported, minimum requirements, and typical applications. Customer support provides information on return policy and customer support information. Glossary provides definition to te
ページ6に含まれる内容の要旨
Fiber Driver EM316E3 & EM316E3SF Features • E3 conversion between coax media and fiber media • Supports ITU-T G.703, ITU-T G.823, and HDB3 standards • Supports Local, Remote and Line Loop back Test • Up to 100km Transmission on Single Mode or 7km on Multimode Fiber • Modules can be Inserted / Removed without powering off the chassis • Extensive Network Management Support when used with EM316NM *For dB budget see: ftp://ftp.fiberdriver.com/pub/doc/spec/fiberdriver Requireme
ページ7に含まれる内容の要旨
Fiber Driver EM316E3 & EM316E3SF Display Information (LED Definition) • PWR: illuminates when unit is powered (green color) • LPBK: illuminates (yellow color) when local loop back on both interfaces is enabled, OFF (no light or green color) when in normal mode • C: illuminates when E3 (coax) interface detected a signal above threshold level • SD: illuminates when Fiber Optic interface detected a signal above threshold level • PLL: illuminates when phase lock loop (PLL) detected enou
ページ8に含まれる内容の要旨
Fiber Driver EM316E3 & EM316E3SF Configuration Jumper Settings: (Factory Default) CONFIGURING THE SWITCH (S1) SWITCH SETTINGS RESULTS *ON Force switches selections (loop back) regardless of NMS command MAN/NMS OFF Default setting comes from switches after power up, but maybe change by NMS commands SEC/PRI ON/OFF Not used in this application. Reserved for the dual-redundant card. Setting is irrelevant to the card ON Loop back mode enabled LPBK/NORMA O
ページ9に含まれる内容の要旨
Fiber Driver EM316E3 & EM316E3SF Theory of Operation Block diagram of the Modem/Converter is shown below (fig. 1) E3 B3ZS FI Encoder Receiver Decoder Transmitter E3 B3ZS Decoder FI Receiver Transmitter Encoder Fig. 1 Fig. 1 Block Diagram of EM316DS3 E3 Line Receiver to fiber optic Transmitter: The receiver Line Interface Unit (LIU) receives the E3 signal and performs clock recovery and data detection. The data goes through B3ZS Decoding Block to ext
ページ10に含まれる内容の要旨
Fiber Driver EM316E3 & EM316E3SF Switch LPBK/NORM is set to OFF Loop back on E3 side Fiber side Coax to near DTE Fig. 3a: External loop back on fiber optic Switch LPBK/NORM is set to OFF Fiber side Loop back on To far EM316E3 E3 side Fig. 3b: External loop back on fiber optic Loop Back Control: By NMS command or manually by a switch Loop back can be forced regardless of management by turning switch 1 MAN/NMS to ON and switch 3 NORM/
ページ11に含まれる内容の要旨
Fiber Driver EM316E3 & EM316E3SF 2 HARDWARE INSTALLATION PREPARATION STEP 1 Follow all Safety Regulations 1 Eliminate static electricity in the workplace by grounding operators, equipment, and devices (components and computer boards). Grounding prevents static charge buildup and electrostatic potential differences. Transporting products in special electrostatic shielding packages avert electrical field damage. 2 An effective workplace should be outfitted with the following items: a)
ページ12に含まれる内容の要旨
Fiber Driver EM316E3 & EM316E3SF f) ESD protective floor or mat: The mat must be grounded through a current- limiting resistor. The floor or mat dissipates the static charge of personnel approaching the workbench. Special conductive tile or floor treatment can be used when mats are not practical or cause a safety hazard. Chairs should be conductive or grounded with a drag chain to the flooring. STEP 2 Determine the best location for the chassis. Affix the chassis to a 19” or 23” rack usi
ページ13に含まれる内容の要旨
Fiber Driver EM316E3 & EM316E3SF UNIT INSTALLATION STEP 1 Remove required amount of blank panels from the NC316BU-xx. NOTE: Per FCC regulations, either a panel or a module should always cover chassis slots. FIGURE 1.1 Take out the required amount of blank panels. STEP 2 Align the edges of the EM316 module to the rail inside the chassis, see pictures below. FIGURE 1.2 Align the edges of the EM316 to the rail inside the chassis and then insert the unit. P/N: 1226006-001, REV_L
ページ14に含まれる内容の要旨
Fiber Driver EM316E3 & EM316E3SF STEP 3 Insert the module into the NC316BU-xx unit NOTE: To avoid damaging any components on the module, handle it by the edges, using your thumb to push it securely inside the chassis. Do not use excessive force, but make sure the module is fully inserted in the chassis. When the module is correctly inserted, the PWR LED should illuminate. STEP 4 Secure the module to the unit, using the screws on the front panel. FIGURE 1.3 When the module is correctl
ページ15に含まれる内容の要旨
Fiber Driver EM316E3 & EM316E3SF 3 TROUBLESHOOTING The Fiber Driver series are highly reliable units. If there are any operating problems, the fault probably lies in some other aspect of the configuration. However, if after following the troubleshooting steps below (in order), you find that the unit is still not functioning correctly, please contact your local representative. Review all link LEDs to ensure that those ports you believe should be functioning are properly attached to
ページ16に含まれる内容の要旨
Fiber Driver EM316E3 & EM316E3SF 4 TECHNICAL SPECIFICATIONS Electrical 5VDC @ 2 Amps Max Hot Swappable Operating Temperature Range 0°C - +50 °C (32°F – 122°F) Storage temp -10°C - +60°C (14°F – 140°F) Relative Humidity 85% maximum non-condensing Emissions Compliance FCC Part 15, Subpart B, 1999 Class A CE Mark EN 50081-1: 1992 EN 50082-1: 1997 EN 55024: 1998 EN 55022: 1998 AS/NZS 3548: 1995 Physical Dimensions 1” high x 3” wide x 7” deep (2.54cm x 7.62cm
ページ17に含まれる内容の要旨
Fiber Driver EM316E3 & EM316E3SF 5 CUSTOMER SUPPORT Contact Information If you have any questions, please do not hesitate to contact us at: Americas Support MRV (East Coast USA) 295 Foster Street Littleton, MA 01460-2016 Tech Support: (800) 338-5316 Tech Support: (978) 952-4700 E-mail: support@fiberdriver.com Fax: (978) 952-4880 URL: http://www.fiberdriver.com MRV (West Coast USA) 20415 Nordhoff St. Chatsworth, CA 91311 Tel. (800) 338-5316 Tel. (818) 773-0900 Inter
ページ18に含まれる内容の要旨
Fiber Driver EM316E3 & EM316E3SF 5 GLOSSARY Complete definition of networking terms (jargon) used in this manual, may be found on our ftp site: ftp://ftp.fiberdriver.com/pub/doc/Glossary.pdf 6 ORDERING INFORMATION Please visit us at http://www.fiberdriver.com for the latest updates on our products. Fiber Driver Division of MRV Chatsworth, CA 91311 Phone: (818) 772-6235 or (800) 966-4444 Fax: (818) 772-0576 Fiber Driver Inquiries: info@fiberdriver.com Marketing:
ページ19に含まれる内容の要旨
Fiber Driver EM316E3 & EM316E3SF P/N: 1226006-001, REV_L PAGE 19 Place Stamp Here ------------------------------------------------ ------------------------------------------------ ------------------------------------------------ 8928 Fullbright Avenue Chatsworth, California 91311 U.S.A.
