Perle Systems C-100-XXXXXの取扱説明書

デバイスPerle Systems C-100-XXXXXの取扱説明書

デバイス: Perle Systems C-100-XXXXX
カテゴリ: ネットワークカード
メーカー: Perle Systems
サイズ: 0.12 MB
追加した日付: 5/8/2013
ページ数: 19
説明書を印刷

ダウンロード

使い方は?

私たちの目的は、皆様方にデバイスPerle Systems C-100-XXXXXの取扱説明書に含まれたコンテンツを可能な限り早く提供することです。オンラインプレビューを使用すると、Perle Systems C-100-XXXXXに関してあなたが抱えている問題に対する解決策の内容が素早く表示されます。

便宜上

説明書Perle Systems C-100-XXXXXをこちらのサイトで閲覧するのに不都合がある場合は、2つの解決策があります:

  • フルスクリーン表示 – 説明書を(お使いのコンピュータにダウンロードすることなく)便利に表示させるには、フルスクリーン表示モードをご使用ください。説明書Perle Systems C-100-XXXXXのフルスクリーン表示を起動するには、全画面表示ボタンを押してください。
  • コンピュータにダウンロード - Perle Systems C-100-XXXXXの説明書をお使いのコンピュータにダウンロードし、ご自身のコレクションに加えることもできます。デバイス上のスペースを無駄にしたくない場合は、いつでもManualsBaseサイトでダウンロードすることもできます。
Perle Systems C-100-XXXXX 取扱説明書 - Online PDF
Advertisement
« Page 1 of 19 »
Advertisement
印刷版

多くの人々は画面表示ではなく印刷された説明書を読むほうを好みます。説明書を印刷するオプションも提供されており、上記のリンクをクリックすることによりそれを利用できます - 説明書を印刷。説明書Perle Systems C-100-XXXXXを全部印刷する必要はなく、選択したページだけを印刷できます。紙を節約しましょう。

要旨

次のページにある説明書Perle Systems C-100-XXXXXの内容のプレビューは、以下にあります。次のページにある説明書の内容をすぐに表示したい場合は、こちらをご利用ください。

内容要旨
ページ1に含まれる内容の要旨


Perle Fast Ethernet
Media Converter
Module


Installation Guide


C-100-XXXXX Unmanaged Module
CM-100-XXXXX Managed Module

P/N 5500306-15

ページ2に含まれる内容の要旨

Overview This document contains instructions necessary for the installation and operation of the Perle Fast Ethernet Media Converter Module(s) (C-100 and CM-100) that are used in conjunction with a Perle MCR Chassis. The C-100 are unmanaged media converter modules, and the CM-100 are the managed versions. These products convert a 100Base-T cable connection (copper) to a 100Base-X connection (fiber). The fiber connection can be either single mode (SM) or multimode (MM) and can operate ove

ページ3に含まれる内容の要旨

Installation The module comes equipped with a bank of DIP switches and jumpers for setting configuration. The default DIP switch settings (all switches in the UP position) and jumper settings will work for most installations.. The following steps are used to configure the Perle Fast Ethernet Media Converter Module: 1. Set the Auto-MDIX jumper (optional). 2. Set the Auto-Config jumper (CM-100 only) (optional) 3. Set the DIP switch settings (optional). 4. Insert the Media Conve

ページ4に含まれる内容の要旨

Auto-Config Jumper (CM-100 only) The Auto-Config jumper (J6) is located just below the Auto-MDIX jumper (see above). Refer to the diagram below for labelling. This jumper only applies to CM-100 modules. Strapping pins 1 and 2 of the jumper will set the module in SW mode and strapping pins 2 and 3 will set it in Auto Config mode. Auto: When set to Auto the module will, at power-up, check its internal flash memory to see if configuration information has been downloaded to it from a ma

ページ5に含まれる内容の要旨

DIP Switches DIP Switch Settings Auto Negotiation (Switch 1) Switch Mode Position Up (default) Auto Down Off Auto: In this mode of operation the Media Converter Module will negotiate Ethernet parameters on the copper connection. This will ensure the most optimal connection parameters will be in effect. If the copper link partner does not support Auto negotiation, the C-100 and CM-100 will default to 100 Mbps and Half Duplex mode. Off: Auto Negotiation should only be turn

ページ6に含まれる内容の要旨

Link Mode (Switch 2) Switch Mode Position Up (default) Link Pass-Through Mode Down Standard Mode Link Pass-Through: In this mode, the link state on one connection is directly reflected through the Media Converter Module to the other connection. If link is lost on one of the connections, then the other link will be brought down. With Media Converters on both ends of the fiber link and both setup for Link Pass-Through, then a loss of copper link on the far end device will propaga

ページ7に含まれる内容の要旨

If the Media Converter has been set to Link Pass-Through mode, the effect will be the same as FEF, since the link loss on the fiber receiver will bring down the copper link, which will in turn cause the transmit fiber link to be brought down. Note: If it is required to either generate or detect the FEF signal, then the FEF switch needs to be set. Disabled: The Media Converter Module will not monitor for, or generate Far End Fault. The following diagram is an illustration of the opera

ページ8に含まれる内容の要旨

Unused (Switch 4) Pause (Switch 5) Switch Mode Position Up (default) Enabled Down Disabled Enabled: When Auto Negotiation has been set to Auto (SW 1), the Media Converter Module will use this setting for its Ethernet parameter negotiation on the copper connection. Disable: The Media Converter Module will not negotiate support for the Pause feature. Note: The Media Converter Module will not act on, or generate any Ethernet Pause messages, but will pass them through to the end

ページ9に含まれる内容の要旨

Installing or Replacing Media Converter Modules Caution: Observe electrostatic discharge precautions when installing the Media Converter Module(s) into the Chassis. Failure to observe this caution could result in damage to the Module(s) and/or chassis. The Perle Media Converter Modules can be installed in any available slot and in any order within the MCR Chassis. Installing or Replacing a Media Converter Module 1. Remove the Media Converter Module from its packaging. 2.

ページ10に含まれる内容の要旨

7. Remove the dust cap from the fiber connector and connect the fiber and copper cables. Removing Media Convert Modules 1. Loosen the captive retainer screw on the front of the Media Converter Module and gently pull the module out. 2. If not inserting a replacement Media Converter Module, cover the opened slot with a face plate and secure the screw. Installing the Duplex Fiber Cable Locate a 100Base-X compliant duplex (2 strands) fiber cable with the appropriate connectors. Co

ページ11に含まれる内容の要旨

Installing the Simplex Fiber Cable • Locate a 100Base-X compliant simplex (1 strand) fiber cable with appropriate connectors. • Connect the fiber cable from one Media Converter Module to another Media Converter/switch/fiber device. Installing the Copper Cable • Locate 100Base-TX compliant copper cables with male, RJ- 45 connectors installed at both ends. • Connect the RJ-45 cable between the Perle Media Converter Module and the device. Note: The Perle Media Converter Module su

ページ12に含まれる内容の要旨

Operation Status LED The Perle Fast Ethernet Media Converter modules have three single color status LEDs located on the face plate of the module. PWR - Power/Test • On: Power is on, module operating normally. • Blinking slowly: the module is in loopback mode. • Blinking quickly: the module has a hardware error. LKF - Fiber Link/Activity • On: Fiber link present. • Blinking quickly: Fiber link present and receiving data. • Off: No fiber link present. LKC - Copper Link/Act

ページ13に含まれる内容の要旨

Other Features Auto-MDIX: Auto-MDIX (automatic medium-dependant interface) detects the signalling on the 100BASE-T interface to determine the type of cable connected (straight-through or crossover) and automatically configures the connection. Error Recovery: In certain configurations, and under specific conditions where the Media Converter Module brings down a link to convey status, there is potential for a deadlock. Recovery is achieved by momentarily restoring the link to se

ページ14に含まれる内容の要旨

Troubleshooting General • Ensure the module is correctly seated to the backplane in the MCR Chassis. The PWR LED should be on solid. • Ensure both devices on either end of the fiber are compatible. If using a simplex fiber connection, ensure that you have both an Upstream (U) and Downstream (D) Media Converter. • Ensure all cabling is of the correct type and is in good working order. • For duplex fiber connections, ensure the RX and TX has been reversed between the two Media Convert

ページ15に含まれる内容の要旨

Method 2: The fiber connection can also be verified by configuring the remote Media Converter for loopback mode. The LKF LEDs on both Media Converters should be lit. Data should pass through the local converter, over the fiber connection to the remote Media Converter. At the remote Media Converter, the data will be looped back and passed through the fiber, once again, to pass through the local converter to the copper link. Note: If troubleshooting a CM-100, setting the Auto-Config jum

ページ16に含まれる内容の要旨

Technical Specifications Power Input/Consumption 12V DC / 2.0 W Operating Temperature: 0 °C to 50 °C (32 °F to 122 °F) Storage Temperature: -25 °C to 70 °C (-13 °F to 158°F) Operating Humidity: 5% to 90% (non-condensing) Storage Humidity: 5% to 95% (non-condensing) Operating Altitude: Up to 3,048 m (10,000 ft) MTBF: (C-100) 574,397 hours (CM-100) 558,531 hours Fiber Optic Specifications Wavelength TX Power RX Power Budget Model Mode (nm) (dB) (dB) (dB)

ページ17に含まれる内容の要旨

C-100-S2SC120 TX: 1550 Min: 0 Min: -35 SM 35 CM-100-S2SC120 RX: 1550 Max: 5 Max: -3 C-100-S2ST120 TX: 1550 Min: 0 Min: -35 SM 35 CM-100-S2ST120 RX: 1550 Max: 5 Max: 0 C-100-S2LC120 TX: 1550 Min: 0 Min: -35 SM 35 CM-100-S2LC120 RX: 1550 Max: 5 Max: -3 C-100-S1SC20U TX: 1310 Min: -14 Min: -32 SM 18 CM-100-S1SC20U RX: 1550 Max: -8 Max: -3 C-100-S1SC20D TX: 1550 Min: -14 Min: -32 SM 18 CM-100-S1SC20D RX:1310 Max: -8 Max: -3 C-100-S1SC40U TX:

ページ18に含まれる内容の要旨

Compliance Information FCC This product has been found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions in this Guide, may cause harmful interference to

ページ19に含まれる内容の要旨

Warranty / Registration Perle’s standard Lifetime Warranty provides customers with return to factory repairs for Perle products that fail under the conditions of the warranty coverage. Details can be found at: http://www.perle.com/support_services/warranty.shtml Contacting Technical Support Contact information for the Perle Technical Assistance Center (PTAC) can be found at the link below. A Technical Support Query may be made via this web page. www.perle.com/support_services/su


類似の説明書
# 取扱説明書 カテゴリ ダウンロード
1 Perle Systems IOLAN CSS 取扱説明書 ネットワークカード 2
2 Perle Systems C-110-XXXXX 取扱説明書 ネットワークカード 0
3 Perle Systems IOLAN STS 取扱説明書 ネットワークカード 13
4 Perle Systems IOLAN SCS 取扱説明書 ネットワークカード 1
5 Perle Systems CM-110-XXXXX 取扱説明書 ネットワークカード 0
6 Perle Systems MEDIA CONVERTERS S-1110DPP 取扱説明書 ネットワークカード 0
7 Perle Systems MEDIA CONVERTERS S-1110PP 取扱説明書 ネットワークカード 0
8 Perle Systems MEDIA CONVERTERS S-1110DP 取扱説明書 ネットワークカード 0
9 Perle Systems Perle 833IS 取扱説明書 ネットワークカード 0
10 Perle Systems MEDIA CONVERTERS S-1110P 取扱説明書 ネットワークカード 0
11 Perle Systems Perle IOLAN DS1 取扱説明書 ネットワークカード 14
12 Perle Systems Perle IOLAN TS2 取扱説明書 ネットワークカード 2
13 Perle Systems 5500320-12 取扱説明書 ネットワークカード 0
14 Perle Systems S-1110-XT 取扱説明書 ネットワークカード 0
15 Perle Systems S-110P 取扱説明書 ネットワークカード 0
16 Sony BTA-NW1A 取扱説明書 ネットワークカード 2
17 Sony BKMW-E3000 取扱説明書 ネットワークカード 2
18 Sony AC-SQ950D 取扱説明書 ネットワークカード 0
19 Sony BBV RX100 取扱説明書 ネットワークカード 3
20 Sony CLIE A-AVZ-100-11 取扱説明書 ネットワークカード 1