ページ1に含まれる内容の要旨
Interface Module User Guide
EAM2000-12
12-Port E1 Access Multiplexer
Net to Net Technologies strongly recommends the use of proper electrostatic discharge (ESD) precautions
CAUTION
when handling this equipment.
INSTALLATION
1. Unpack and inspect the EAM2000-12.
If there is visible damage, do not attempt to connect the device; contact Customer Support at 1-
877-638-2638 (001-603-427-0600 for international customers) or Support@NetToNet.com.
2. Install the EAM2000-12 in an IP DSLAM chassis.
The
ページ2に含まれる内容の要旨
3. Connect the E1 Line(s). Plug the E1 cable into the RJ21 connector for the chosen slot on the back of the IP DSLAM. The EAM2000-12 will connect with remote E1 modems at distances up to 6,000 feet before requiring an E1 repeater. For each port being connected to a remote E1 modem, verify that the E1 link has been established; the E1 LK LED for that port will show steady illumination to indicate the connection has been made. Link up should occur within 20 seconds depending on the quality, g
ページ3に含まれる内容の要旨
! 192.168.254.252 if the MUM is in slot 13 (IPD12000) or slot 5 (IPD4000) ! 192.168.254.253 if the MUM is in slot 14 (IPD12000) e. Log in with a default username and password (both of which are case sensitive). Please note that General Users have "read only" access; for NMS configuration you must log in as a Superuser. ! general / Password superuser / Password ! Once accessed initially, the management system within the MUM can be configured such that NMS NOTE and SNMP can be reached from
ページ4に含まれる内容の要旨
Management System Configuration Defaults IP Addresses: Subnet Mask: 255.255.255.0 IPD12000 slot 13 192.168.254.252 Default Gateway: 0.0.0.0 IPD12000 slot 14 192.168.254.253 In-band Management: disabled IPD4000 slot 5 192.168.254.252 Uplink VLAN ID: 0 EAM2000-12 Circuit Defaults Circ. ID: n/a Pri [Priority]: 0 IP Range 1: 0.0.0.0 - 255.255.255.255 Flood: Upl [Uplink] IP Range 2: 0.0.0.0 - 0.0.0.0 Frame Type: CRC [Cyclic Redundancy Check] Speed: 1,984 kbps Line Code: HDB3 [High Density Binary 3] P
ページ5に含まれる内容の要旨
Although all 31 channels continually run at 1,984 kbps, the Timeslot configuration for each port determines NOTE how many of the channels will be receiving data for that port. Ports configured to operate as fractional E1 lines require contiguous timeslots, as indicated in the table above. Frame Type Frame type is the E1 data encapsulation method. A frame consists of 248 bits (8-bit samples of each of the 31 E1 channels plus a synchronization bit) transmitted at a rate of 8,000 frames per sec
ページ6に含まれる内容の要旨
ADDITIONAL INFORMATION LED Indicators LED State Indication Additional Information PWR (Power) solid green unit is operational If the Power LED is not illuminated, it is unlikely the EAM2000-12 is receiving power and none of the LEDs will be illuminated. E1 LK (Link) solid green E1 connection is established An E1 link exists and the port may be transmitting data but it is not receiving any packets from the remote E1 modem. pulsing E1 connection is established and active The port is receivin
ページ7に含まれる内容の要旨
Regulatory Compliance European Regulatory Compliance Information for Class A Equipment This Class A product complies with European Norm EN55022. Warning: In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures to correct the situation. 210-0000036 rev03 © Copyright 2001 Net to Net Technologies, Inc. ™ The Net to Net Logo is a trademark of Net to Net Technologies, Inc. Worldwide Headquarters http://www.NetToNet.com/
