ページ1に含まれる内容の要旨
Freescale Semiconductor, Inc.
MOTOROLA
Metrowerks
SW/HW Dept
MSC8101 ADS
User’s Manual
Revision B
(Revision Release 1.2)
Dragilev Lev
SW/HW Dept
Motorola Semiconductor Israel
1 Shenkar Street,
Herzlia 46120, Israel
TEL: 972-9-522-579
email: Lev.Dragilev@motorola.com
FAX: 972-9-9562990
25/1/2004
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc...
ページ2に含まれる内容の要旨
Freescale Semiconductor, Inc. MSC8101ADS RevB User’s Manual For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc...
ページ3に含まれる内容の要旨
Freescale Semiconductor, Inc. CONTENTS 1•1Introduction 11 1•2 Abbreviations’ List 11 1•3 Related Documentation 11 1•4Specification 12 1•5 ADS Features 13 2•1INTRODUCTION 16 2•2 UNPACKING INSTRUCTIONS 16 2•3 HARDWARE PREPARATION 16 2•3•1 Setting The Core Supply Voltage Level 18 2•3•2 Setting MODCK(1:3) For Initial PLLs’ Multiplication Factor - SW9 18 2•3•3 Setting HReset Configuration Source 18 3•1 OnCE Connection Scheme 19 3•2 Host I/F Operatio
ページ4に含まれる内容の要旨
Freescale Semiconductor, Inc. 4•4•4 Ethernet LINK Indicator - LD4 33 4•4•5 Fast Ethernet CLSN Indicator - LD5 33 4•4•6 ATM RX Indicator - LD6 33 4•4•7 ATM TX Indicator - LD7 33 4•4•8 TEXP Indicator - LD8 33 4•4•9 Signaling Indicator 1 - LD9 33 4•4•10 Signaling Indicator 0 - LD10 33 4•4•11 RS232 Port 2 ON - LD11 33 4•4•12 RS232 Port 1 ON - LD12 33 4•4•13 Fast Ethernet Port Initially Enabled - LD13 33 4•4•14 ATM ON - LD14 34 4•4•15 T1-1 TDM Port 1 Enable - LD15 34 4•4•16 T1-234 TDM Ports 2,3
ページ5に含まれる内容の要旨
Freescale Semiconductor, Inc. 5•11•1 BCSR0 - Board Control / Status Register 0 55 5•11•2 BCSR1 - Board Control / Status Register 1 56 5•11•3 BCSR2 - Board Control / Status Register 2 58 5•11•4 BCSR3 - Board Status Register 3 59 7•1 Power rails. 65 7•1•1 5V Bus 66 7•1•2 3.3V Bus 66 7•1•3 1.5V Bus 66 A•1BOM 68 B•1 Interconnect Signals 76 B•1•1 MSC8101ADS’s P1- System Expansion Connector 76 B•1•2 MSC8101ADS’s P2 - CPM Expansion Connector 82 B•1•3 P3 - Altera’s In System Programming (ISP) 90 B
ページ6に含まれる内容の要旨
Freescale Semiconductor, Inc. VI MSC8101ADS RevB User’s Manual MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc...
ページ7に含まれる内容の要旨
Freescale Semiconductor, Inc. LIST OF FIGURES FIGURE 1-1 MSC8101ADS Block Diagram 15 FIGURE 2-1 MSC8101ADS Top Side Part Location diagram 17 FIGURE 3-1 Host System Debug Scheme A 19 FIGURE 3-2 Host System Debug Scheme B 20 FIGURE 3-3 Stand Alone Configuration 21 FIGURE 3-4 P26: +5V Power Connector 21 FIGURE 3-5 P6 - JTAG/OnCE Port Connector 22 FIGURE 3-6 P4 - Host I/F Connector 23 FIGURE 3-7 P27A - Upper RS-232 Serial Port Connector 24 FIGURE 3-8 P27B
ページ8に含まれる内容の要旨
Freescale Semiconductor, Inc. VIII MSC8101ADS RevB User’s Manual MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc...
ページ9に含まれる内容の要旨
Freescale Semiconductor, Inc. LIST OF TABLES TABLE 1-1. MSC8101ADS Specifications 12 TABLE 4-1. Available Clock Mode Setting 29 TABLE 4-2. JP1/JP2 Settings 31 TABLE 4-3. SIU Registers’ Programming 35 TABLE 4-4. Memory Controller Initialization for 100(50) MHz 36 TABLE 5-1 Summary Reset Configuration Schemes. 40 TABLE 5-2. Hard Reset Configuration Word 40 TABLE 5-3. MSC8101ADS Chip Select Assignments 44 TABLE 5-4. 100 MHz SDRAM Mode Register Programming 45 TABLE 5
ページ10に含まれる内容の要旨
Freescale Semiconductor, Inc. T-X MSC8101ADS RevB User’s Manual MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc...
ページ11に含まれる内容の要旨
Freescale Semiconductor, Inc. General Information 1 - General Information 1•1 Introduction This document describes the engineering specifications of the MSC8101ADS board based on the MSC8101- first member of the family of programmable DSP based around the SC100 DSP cores. It integrates a high-performance Star*Core SC140 DSP is four ALU DSP Core, large on-chip memory (1/2 MByte), Communication Processor Module compatible with PowerQUICCII (MPC8260) CPM, a very flexible system integrat
ページ12に含まれる内容の要旨
Freescale Semiconductor, Inc. General Information [5] PMC-SIERRA 5350 Long Form Data Sheet [6] PMC-SIERRA 5350 Errata Notice [7] PMC-SIERA 5350 Reference Design [8] LXT970A (by Level One) Data Sheet [9] LXT970 Demo Board User’s Guide 1•4 Specification The MSC8101ADS specifications are given in TABLE 1-1. "MSC8101ADS Specifications" below TABLE 1-1. MSC8101ADS Specifications CHARACTERISTICS SPECIFICATIONS Power requirements (no other boards attached) +5V DC @ 2A (Typ.), 3A (Max.) MSC8
ページ13に含まれる内容の要旨
Freescale Semiconductor, Inc. General Information 1•5 ADS Features o 64-bit MSC8101, running up to @ 100MHz external bus frequency. o 8 MByte, 80 pin Flash SIMM reside after buffer. Support for up to 32 MByte, con- trolled by GPCM, 5V Programmable, with Automatic Flash SIMM identification, via BCSR. o 16 MByte unbuffered SDRAM on PPC bus, controlled by SDRAM machine, sol- dered directly on the board. Data bus width 64/32 bits is controlled by Jumper Ar- ray. The narrow data bus configur
ページ14に含まれる内容の要旨
Freescale Semiconductor, Inc. General Information o On-board 1.2V - 2.2V adjustable for MSC8101 Internal Logic Operation and 3.3V±10% fixed Voltage Regulators for other circuits. May be bypassed in case of external power supplying. o Software Option Switch provides 8 S/W options via BCSR. o LED’s for power supply, module enables, timer expired and SW indications. 14 MSC8101ADS RevB User’s Manual MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semicond
ページ15に含まれる内容の要旨
Freescale Semiconductor, Inc. General Information FIGURE 1-1 MSC8101ADS Block Diagram 3.3V * 2 1 SDRAM PPC (non-buffered) D[0:59] 2Megx32 Address Mux for variable Port Size 64/32 36pin HOST Buffers 28 Clock D[32:59] 16.4/25MHz HOST I/F Ext CLK Reset,Config Interrupts DATA Transceivers & Address Buffers 5V D[0:31] PPC Bus (buffered) Flash SIMM. 8 - 32MByte MSC8101 32 - Bit 332 pin 0.8mm 19x19 matrix 3.3V<->5V 3ns (3M Socket) Flash Detect Clock Buffer 1 ClkOut 7 14pin JTAG/OnCE DLLIN SCC
ページ16に含まれる内容の要旨
Freescale Semiconductor, Inc. Hardware Preparation 2 - Hardware Preparation 2•1 INTRODUCTION This chapter provides unpacking instructions, hardware preparation, and installation instructions for the MSC8101ADS. 2•2 UNPACKING INSTRUCTIONS NOTE If the shipping carton is damaged upon receipt, request carrier’s agent to be present during unpacking and inspection of equipment. Unpack equipment from shipping carton. Refer to packing list and verify that all items are present. Save packi
ページ17に含まれる内容の要旨
Freescale Semiconductor, Inc. Hardware Preparation FIGURE 2-1 MSC8101ADS Top Side Part Location diagram Boot Mode SW S/W Opt EE SW 64/32 Select Host SW Config SW MOTOROLA MSC8101ADS RevB User’s Manual 17 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc...
ページ18に含まれる内容の要旨
Freescale Semiconductor, Inc. Hardware Preparation 2•3•1 Setting The Core Supply Voltage Level The internal Logic & PLL’s of the MSC8101 is powered separately through a supply bus named 1V5. The voltage level over this power bus may vary between 0.9V - 2.1V. In the lower voltage level, the Processor will operate at lower frequency range, consuming a smaller amount of power and vice-versa for the higher voltage level. 1V5 power level is factory set for 1.5V, but may be changed by RP2. 2•3•
ページ19に含まれる内容の要旨
Freescale Semiconductor, Inc. Installation Instructions 3 - Installation Instructions The MSC8101ADS may be configured according to the required working environment as follows: • Host Controlled Operation through OnCE Port • Host Interface Operation through HDI16 Port • Stand-Alone Mode 3•1 OnCE Connection Scheme In this configuration the MSC8101ADS is controlled by a host computer via the OnCE Port, which is a subset of the JTAG port. This configuration allows for extensive debuggin
ページ20に含まれる内容の要旨
Freescale Semiconductor, Inc. Installation Instructions FIGURE 3-2 Host System Debug Scheme B Host Computer Command Media I/F Converter Host 36Wire Device Flat Cable 14 Wire Flat Cable To JTAG/OnCE 5V Power Supply 3•3 Stand Alone Operation In this mode, the ADS is not controlled by the host via the OnCE port. It may connect to host via one of its other ports, e.g., RS232 port, Fast Ethernet port, ATM155 port etc. Operating in this mode requires an application program to be programmed
