ページ1に含まれる内容の要旨
HENKEL, INC
P.O. BOX 1322
HAMMOND, LA 70404
(985) 345-2171
www.keenovens.com
ページ2に含まれる内容の要旨
Henkel, Inc. P.O. Box 1322 * Hammond, Louisiana * 70404 * (985) 345-2171 www.keenovens.com Models K-900 & K-1000 Holding Ovens Installation Instructions & Repair Parts List One Year Limited Warranty Henkel, Inc. warrants its products against defects in material and workmanship. Henkel, Inc. will either repair or replace without charge any properly installed product which fails under normal operating conditions within one year from date of installation, provided
ページ3に含まれる内容の要旨
K-900 SPECIFICATIONS Electrode Capacity 1000lbs. 18" rods Volts 120V 240V 480V Watts 3000W 3000W 3000W Thermostat Dial Adjustable Temperature 150ºF-500ºF Insulation 2" Interior Dimensions 18" X 18.5" X 36" Net Weight 175 lbs. Shipping Weight 282 lbs. Shipping Dimensions 30" X 30.5" X 53" K-1000 SPECIFICATIONS Electrode Capacity 1500lbs. 18" rods Volts (Specifiy) 120V 240V
ページ4に含まれる内容の要旨
Safety Precautions Read all instructions completely before attempting to operate this unit. *** SAVE THESE SAFETY INSTRUCTIONS *** To reduce the risk of electrical shock, fire, or personal injury follow the guidelines below: • Before connecting unit to a power source, be sure the voltage supplied is the same as that specified on the name plate of the unit. • Check outlet to ensure proper grounding of the electrical cable. Have a licensed electrician check the A/C power outlet if
ページ5に含まれる内容の要旨
Temperature Setting The thermostat is adjustable from 150 °F (37.8 °C) to 550 °F (287.8 °C). Turn thermostat knob to desired temperature by aligning with red line on chrome bezel. Pilot light indicates when power supply is supplied to the heating elements. The thermostat is accurate to ±25 °F (14 °C) a the sensor. Temperature variance is minimal throughout the oven due to the heat exchanging qualities of the Keen shelving system. ***CAUTION: DO NOT USE ON D/C POWER SUPPLY! ***
ページ6に含まれる内容の要旨
IF OVEN FAILS TO OPERATE – NO HEAT 1. Check power source. 2. Check power cord continuity. Replace cord assembly if faulty. 3. If pilot light glows, voltage is being supplied by elements. Check elements. Check element continuity. If defective, replace. 4. If thermostat cannot be heard clicking on and off when dial is rotated, and if pilot light fails to operate, replace thermostat. IF OVEN OPERATES BUT FAILS TO REACH TEMPERATURE 1. Check name plate for proper voltage. Check volta
ページ7に含まれる内容の要旨
CHANGING THE THERMOSTAT 1. Disconnect from the power source. 2. Remove cover plate from control box and disconnect wire connectors from thermostat leads. 3. Remove thermostat knob and chrome bezel. Knob is secured by recessed set screw. 4. From the inside of the oven, remove sensing tube from holder. Thermostat may now be removed and sensing tube pulled through side wall of oven. 5. Remove leads from old thermostat and place on new, being sure leads are securely screwed in place. 6. T
ページ8に含まれる内容の要旨
480Volts/3000 Watts Grounding Plug 480 V/20A NEMA L8-20P Not Provided 480Volts 3 Phase Grounding Plug 480 V/20A NEMA L8-20P Not Provided
ページ9に含まれる内容の要旨
Model K-900& K-1000 Repair Parts List ITEM # QUANTITY DESCRIPTION PART NUMBER 11 Shelf Assembly 2 1 Door Pull 430102 3 2 Draw Pull Catches 430106 4 1 Handy Box 301033 5 1 Thermostat 301038 6 1 Neon Pilot Light 301085 7 3 Heating Elements 120V 301023 240V 301026 480V 301029 8 1 8' Power Cord 120V 301014 240V/480V 301097 9 1 Strain Relief 120V 301041 240V/480V 301043 10 1 Door 11 1 Back Cover 12 1 Name Plate 450103 13 1 Control Box K-900 & K-1000 W/T ACCESSORIES LIST ** Please state model n
ページ10に含まれる内容の要旨
Phone (985) 345-2171 HENKEL, INC. Fax (985) 345-5653 PO Box 1322 Manufacturer of KEEN Ovens Hammond, Louisiana Quality Since 1923. 70401 Flux and Electrode Stabilizing Guide Dry Rod After Exposure to Moisture a Air Conditioned Oven Holding Sufficient Time to affect Weld Quality Storage Type (AWS) After Opening Recondition Rebake Before Opening IMPORTANT: Step 1 Step 2 This table is offered as a Standard 180 °F ± 25 ° 240 °F ± 25 ° guide to
