ページ1に含まれる内容の要旨
USER MANUAL
i15
ページ2に含まれる内容の要旨
CONTENTS 1. Introduction 2. Unpacking 3. Connectors/Cabling 4. Polarity Checking 5. Amplification & Power Handling 6. Crossovers 7. Equalisation 8. Dimensions 9. Rigging 10. Performance Data 11. Technical Specifications 12. i15 Recommended Service Parts & Accessories 13. Warranty 14. Wall Mounting Bracket - Assembly Instructions 15. Declaration of Conformity
ページ3に含まれる内容の要旨
1. Introduction of compact system, capable of delivering high sound pressure levels with extremely low distortion, resulting in outstanding clarity, definition and detail. resulting in a smooth uniform frequency response over a wide area of coverage arrays have minimal lobing. These features are inherent and achieved without the Designed for fixed installations, the i15 is constructed from medium density fibreboard (MDF), for a high level of acoustic damping. The structural integrity of the encl
ページ4に含まれる内容の要旨
Neutrik or its distributors directly on the following numbers :- UK: N EUTRIK M ARKETING: USA: N EUTRIK USA I NC.: :- N EUTRIK AG: (damping factor). .5 sq. mm (12 gauge) cable. This will be perfectly satisfactory under normal conditions. In the case of very long cable :- CABLE RUN C.S.A. OF EACH CABLE % POWER LOSS % POWER LOSS (m) CONDUCTOR (mm) RESISTANCE Ω Ω INTO 8Ω Ω LOAD INTO 4Ω Ω LOAD 10 2.5 0.14 1.7 3.5 4.0 0.09 1.1 2.2 6.0 0.06 0.73 1.5 25 2.5 0.35 4.3 8.6 4.0 0.22 2.7 5.4 6.0 0.14 1.8 3.
ページ5に含まれる内容の要旨
5. Amplification & Power Handling voice coil thermal capacity. Care should be taken to avoid running the amplifier into clip (clipping is the end result of overdriving any amplifier). Damage to the loudspeaker will be sustained if the amplifier is driven into clip for any extended period of time. Headroom of at least 3dB should be allowed. When evaluating an amplifier, it is important to take into account its behaviour under low impedance load Generally a higher power amplifier running free from
ページ6に含まれる内容の要旨
8. Dimensions
ページ7に含まれる内容の要旨
9. Rigging
ページ8に含まれる内容の要旨
10. Performance Data
ページ9に含まれる内容の要旨
11. Technical Specifications Frequency Response (1) +/- 3dB Recommended Amplifier Power Power Handling(2) Sensitivity (1) 2.83 volt @ 1m Maximum SPL (3) @ 1m Impedance DI Averaged (PCQ) @ 1kHz (ISO) @ 2kHz (ISO) @ 4kHz (ISO) 9 @ 8kHz (ISO) @ 16kHz (ISO) Q Averaged (PCQ) @ 1kHz (ISO) @ 2kHz (ISO) @ 4kHz (ISO) @ 8kHz (ISO) @ 16kHz (ISO) Distortion 0.1 Full Power 2nd Harmonic 3rd Harmonic 250 Hz 1000 Hz 10000 Hz 0.01 Full Power 2nd Harmonic 3rd Harmonic 250 Hz 1000 Hz 10000 Hz Below measurement
ページ10に含まれる内容の要旨
12. i15 Service Parts & Accessories Part Number Description Driver Kit - 3804 HF Diaphragm Kit Paint - Touch up Black-Grey Flying Kit ( 3 x M8 Eyebolts ) Wall Mounting Bracket Active System Controller/2-way Stereo Crossover 13. Warranty the date of manufacture subject to the absence of misuse, overload or accidental removed. further information please contact your dealer or distributor in your country. If you Customer Services ML5 4TF (National) Fax: (National) e-mail: Our policy commits us
ページ11に含まれる内容の要旨
14. Wall Mounting Bracket - Assembly Instructions A dedicated wall mounting bracket (Part No. 8000 0671) is available for the i15. :- side of the cabinet, place the T- Bar in position and fix in place using the two cap- shown on the diagram below. It is imperative that the bracket is fixed soundly to the Portrait mounting top of Exploded View of Bracket Assembled View of Bracket the cabinet. the above instructions, removing two of the original M8 countersunk screws on - Using a hacksaw, cut
ページ12に含まれる内容の要旨
Declaration of Conformity The following apparatus is/are manufactured in the United Kingdom by Tannoy Ltd of Rosehall Industrial estate, Coatbridge, Scotland, ML5 4TF and conform(s) to the protection requirements of the European Electromagnetic Compatibility Standards and Directives relevant to Domestic Electrical Equipment. The apparatus is designed and constructed such that electromagnetic disturbances generated do not exceed levels allowing radio and telecommunications equipment and other app
