ページ1に含まれる内容の要旨
OWNER’S MANUAL
PLL SYNTHESIZER STEREO RADIO WITH
COMPACT DISC PLAYER DIGITAL
VBD 500
ページ2に含まれる内容の要旨
INSTALLATION Notes: • Choose the mounting location where the unit will not interfere with the normal driving function of the driver. • Before finally installing the unit, connect the wiring temporarily and make sure it is all connected up properly and the unit and the system work properly. • Use only the parts included with the unit to ensure proper installation. The use of unauthorized parts can cause malfunctions. • Consult with your nearest dealer if installation requires the drilling of
ページ3に含まれる内容の要旨
1. Dashboard 1 2. Nut (5mm) 6 3. Spring washer 7 4 4. Screw (5 x 25mm) 5 5. Screw 2 3 6. Strap Be sure to use the strap to secure the back of the unit in place. The strap can be bent by hand to the desired angle. (Fig. 2) 7. Plain washer Removing the unit 1. Frame 1 2. Insert fingers into the groove in the front of frame and pull out to remove the frame. (When re-attaching the frame, point the side with a groove downwards and attach it.) 3 3. Lever Insert the levers supplied with the unit
ページ4に含まれる内容の要旨
USING THE DETACHABLE FRONT PANEL To Detach the Front Panel 1. Press the open button (open), then the front panel will be folded down. Open 2. Remove the front panel by pulling its middle-hand outward. Front Panel 3. For safekeeping, store the front panel in the supplied protective case immediately after being removed. Protective case Front panel 4. Push the front metal plate into the main body. A ‘click’ sound should be heard. 4
ページ5に含まれる内容の要旨
To Reinstall the Front Panel 1. Push the front panel into the main body. A ‘click’ sound should be heard. 2. Note that if the front panel fails to lock in position properly, press control button may not function and LCD display may be missing some segments. Pushing the open button and then reinstall the front panel again. Precautions when Handling 1. Do not drop the front panel. 2. Do not put pressure on the display or control buttons when detaching or reinstalling the front panel. 3. Do not
ページ6に含まれる内容の要旨
WIRING CONNECTION MAIN UNIT ANTENNA CONNECTOR (GREEN) SUBWOOFER CABLE IGNITION RED SWITCH (B+) YELLOW MEMORY BACK-UP (GREY) BLACK Rch RED RCA CABLE GROUND (B–) Lch WHITE BLUE POWER ANTENNA WHITE GREY FRONT Lch FRONT Rch SPEAKER SPEAKER WHITE/BLACK GREY/BLACK GREEN VIOLET REAR Lch REAR Rch SPEAKER SPEAKER GREEN/BLACK VIOLET/BLACK 6
ページ7に含まれる内容の要旨
OPERATION 12 7 3 2 1 8 16 20 26 9 18 13 11 10 19 21 22 23 15 24 6 14 17 5 25 27 4 GENERAL OPERATION • ON/OFF Switch on the unit by pressing any button [except OPEN button (7) and EJECT button (4)]. When system is on, press PWR button (9) to turn off the unit. •FACEPLATE RELEASE Press OPEN button (7) to detach the removable faceplate. 7
ページ8に含まれる内容の要旨
• SOUND ADJUSTMENT Press SEL button (11) to select the desired adjustment mode. The adjustment mode will change in the following order: Volume Bass Treble Balance Fader By pressing VOLUME button (12) or VOLUME button (13), it is possible to adjust the desired sound quality. • LOUDNESS Press LOU/BND button (14) for several seconds to reinforce the bass output and display will show “LOUD”. Press it for several seconds again to release this function. • SET THE CLOCK Holding down the DSP
ページ9に含まれる内容の要旨
RADIO OPERATION • BAND SELECTION At tuner mode, press LOU/BND button (14) shortly to select the desired band. The reception band will change in the following order: FM1 FM2 FM3 AM •STATION SELECTION Press MAN/SEK button (17) or MAN/SEK button (18) shortly to activate automatic seek function. Press for several seconds until “MANUAL” appeared on the display, the manual tuning mode is selected. If both buttons have not pressed for several seconds, they will retune to seek tuning mode
ページ10に含まれる内容の要旨
CD OPERATION • SELECT TRACKS Press MAN/SEK button (17) or (18) to move to the previous track or the following track. Track number shows on display. Hold MAN/SEK button (17) or (18) to fast reverse or fast forward. CD play starts from when you release the button. • STOP PLAYING Press PAU button (21) to pause CD player. Press it again to resume play. • REPEAT THE SAME TRACK Press RPT button (23) to continuously repeat the same track. Press again to stop repeat. • PREVIEW A
ページ11に含まれる内容の要旨
REMOTE CONTROL HANDSET 3 1 2 4 5 9 6 8 7 10 13 14 12 11 15 CONTROL & FUNCTION KEYS 1. POWER = Power ON/OFF Button 2.MOD =Mode Button 3. S (SEL) = Select Button 4. DSP = Display Button 5. BND = Band Select Button 6. AMS = Automatically Memory Storing & Program Scanning Button 7. VOL + = Volume Up Button 8. VOL – = Volume Down Button 9. TUN/SEK =Tune/Seek Up Button 10. TUN/SEK = Tune/Seek Down Button 11. M1 - M6 = Preset Buttons 12. PAU = Pause Button 13. SCN = Scanning Button 14. RPT = Repeat B
ページ12に含まれる内容の要旨
SPECIFICATION GENERAL Power Supply Requirements : DC 12 Volts, Negative Ground Chassis Dimensions : 178 (W) x 163 (D) x 50 (H) Tone Controls - Bass (at 100 Hz) : +10 dB / –10 dB - Treble (at 10 KHz) : +10 dB / –10 dB Maximum Output Power : 50W x 4 (ch) Current Drain : 15 Ampere CD PLAYER Signal to Noise Ratio : More than 60 dB Channel Separation : More than 60 dB Frequency Response : 20 Hz - 20 KHz RADIO FM Frequency Coverage : 87.5 to 107.9 MHz IF : 10.7 MHz Sensitivity (S/N = 30 dB) : 3 µ V St
ページ13に含まれる内容の要旨
TROUBLE SHOOTING Before going through the check list, check wiring connection. If any of the problems persist after check list has been made, consult your nearest service dealer. Symptom Cause Solution No power. The car ignition is not on. If the power supply is properly connected to the car accessory terminal, switch the ignition key to “ACC”. The fuse is blown. Replace the fuse. Disc cannot Presence of CD disc Remove the disc in the player, then be loaded or inside the player. put a new one.
ページ14に含まれる内容の要旨
ページ15に含まれる内容の要旨
ページ16に含まれる内容の要旨
www.lanzar.com 88-C0660-22
