ページ1に含まれる内容の要旨
Honeywell
TABLE OF CONTENTS
INTRODUCTION 3
Wireless Thermo-Hygrometer
PRODUCT OVERVIEW 4
REMOTE SENSOR 7
BEFORE YOU BEGIN 8
BATTERY INSTALLATION 9
LOW BATTERY WARNING 10
GETTING STARTED 10
COMFORT LEVEL INDICATORS 11
MAXIMUM AND MINIMUM MEMORY 12
AUTO-SCANNING 12
LOST COMMUNICATION 13
TRANSMISSION COLLISION 14
PRECAUTIONS 14
SPECIFICATIONS 16
FCC STATEMENT 17
DECLARATION OF CONFORMITY 18
STANDARD WARRANTY INFORMATION 19
(TM005X)
USE
ページ2に含まれる内容の要旨
INTRODUCTION PRODUCT OVERVIEW Thank you for selecting the Honeywell Wireless Thermo-Hygrometer MAIN UNIT with Remote Sensor. This device monitors and displays temperature FEATURES and humidity both indoors and outdoors from up to three remote • Wireless transmission of the temperature and humidity from the locations. remote sensor to the main unit from up to 100 feet (30 meters) In this package you will find: away • One main unit (receiver) • Indoor temperature and relative humidity di
ページ3に含まれる内容の要旨
FRONT VIEW REAR VIEW A. TEMPERATURE AND HUMIDITY INFORMATION IN A E TWO LINE LCD DISPLAY F G H E. WALL-MOUNT RECESSED OPENING • Keeps the main unit on the wall D B C F. BATTERY COMPARTMENT B. CHANNEL BUTTON • Accommodates 2 (two) UM-3 or AA 1.5V alkaline batteries. • Selects the desired remote channel or indoor readings G. C°/F° SWITCH (located inside the battery compartment) C. SEARCH BUTTON • Selects temperature display in Celsius or Fahren
ページ4に含まれる内容の要旨
REMOTE SENSOR • Selects the desired channel FEATURES E. WALL-MOUNT RECESSED OPENING • Remote temperature and humidity transmission to the main • Keeps the remote sensor on the wall unit via 433 MHz signal F. °C/ °F SELECTOR • 100 feet (30 meters) transmission range without interference • Selects the temperature display in Celsius or Fahrenheit • LCD display of measured temperature and humidity • Three (3) channels selection • Selection of the temperature display in Celsius or Fahrenhe
ページ5に含まれる内容の要旨
NOTE: MAIN UNIT 1. Avoid pressing any buttons on the main unit before the remote • Open the battery compartment door. temperature is displayed for about 2 minutes. • Install 2 batteries (UM-3 or “AA” size 1.5V) matching the 2. The effective operating range may be influenced by the surrounding polarity as shown in the battery compartment. building materials and how the receiver and transmitter are positioned. • Replace the battery compartment door. 3. Place the remote sensor so that it
ページ6に含まれる内容の要旨
The remote temperature and humidity for channel one, two and three Indicator Temperature Humidity Shows current can be recalled by pressing CHANNEL button. displayed Range Range condition The wave icon is located above the remote channel number and Ideal for both 20°C to 25°C 40%RH- indicates the reception status from the remote sensor. relative humidity ☺ (68°F to 77°F) 70%RH The following three types of reception status may be displayed: and temperature -5°C to 50°C OVER Con
ページ7に含まれる内容の要旨
displayed one-by-one automatically for 4 seconds each in the following • Remove the batteries from the battery compartment and reinstall sequence: Indoor, Channel 1, Channel 2 and Channel 3. them in the same manner. Remote sensor LED indicator will To exit from scanning mode, press and hold the CHANNEL button for flash showing transmission of the signal. 2 seconds, and the icon “ ” will disappear, returning the main unit • Remove the batteries from the main unit and reinstall them in dis
ページ8に含まれる内容の要旨
invalidate the warranty and may cause damage. These units SPECIFICATIONS Main Unit contain no user-serviceable parts. Indoor Temperature • Use only fresh batteries. Do not mix new and old batteries. Proposed operating range: -5.0°C to +50.0°C/23.0°F to 122.0°F Temperature resolution: 0.1°C/0.2°F • Read the user's manual thoroughly before operating the units. User-selectable (F° or C°) temperature display Indoor Humidity Proposed operating range: 20% to 95% Humidity resolution: 1% Co
ページ9に含まれる内容の要旨
FCC STATEMENT DECLARATION OF CONFORMITY This device complies with Part 15 of the FCC Rules. Operation is We subject to the following two conditions: (1) This device may not cause Name: Hideki Electronics, Inc. harmful interference, and (2) This device must accept any interference Address: 7865 SW Mohawk, Tualatin, OR 97062 received, including interference that may cause undesired operation. Telephone No.: 1-503-612-8395 Warning: Changes or modification to this unit not expressly approved d
ページ10に含まれる内容の要旨
STANDARD WARRANTY INFORMATION This product is warranted from manufacturing defects for one year from date of retail purchase. It does not cover damages or wear resulting from accident, misuse, abuse, commercial use, or unauthorized adjustment and repair. Note that online product registration is required to ensure valid warranty protection. To register your product, go to our Company website at: www.hidekielectronics.us . Click Online Product Registration under the Customer Support menu.
