ページ1に含まれる内容の要旨
Pool System
Owners Manual
Customer Service Center
• N53 W24700 South Corporate Circle • Sussex, WI 53089 • U.S.A.
REQUIRED TOOLS AND MATERIALS:
Read and understand
operator's manual before
• Two People
using this unit.
• Garden Hose or Sand (360 lb.) (163 kg)
• Wrenches: (Two) 1/2” (One) 9/16” or
Failure to follow operating
Two Small Adjustable Wrenches
instructions could result
• 9/16” Deep Socket w/Ext.
in injury or damage to
Recommended
property.
Toll-Free Customer Service Number for U.S:
ページ2に含まれる内容の要旨
SAFETY INSTRUCTIONS FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN SERIOUS INJURY OR PROPERTY DAMAGE AND WILL VOID WARRANTY. Owner must ensure that all players know and follow these rules for safe operation of the system. To ensure safety, do not attempt to assemble this system without following the instructions carefully. Check entire box and inside all packing material for parts and/or additional instruction material. Before beginning assembly, read the instructions and identify
ページ3に含まれる内容の要旨
NOTICE TO ASSEMBLERS ALL Huffy Sports Basketball Systems, including those used for DISPLAYS, MUST be assembled and ballasted with sand or water according to instructions. Failure to follow instructions could result in SERIOUS INJURY. It is NOT acceptable to devise a makeshift weight system. IMPORTANT! Remove all contents from boxes. Be sure to check inside pole sections, hardware and additional parts are packed inside. WARRANTY CARD: Please remember to complete your product registration form e
ページ4に含まれる内容の要旨
Get to know the basic parts of your basketball system..... FRONT STRUTS EXTENSION ARM POLE BASE WHEEL CARRIAGE ASSEMBLY 4 P/N 211988B 03/03
ページ5に含まれる内容の要旨
WARNING FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. Owner must ensure that all players know and follow these rules for safe operation of the system. See instruction manual for proper installation and maintenance. DO NOT position system near trampolines, diving boards, slides or any play area equipment. System misuse could result in serious bodily injury. DO NOT perform dunk type activities on this system. DO NOT hang from any part of system,
ページ6に含まれる内容の要旨
PARTS LIST (See Hardware Identifier) Item Qty. Part No. Description 17 12* 201219 Clip, Net Holder Item Qty. Part No. Description 1 1 206740 Tank (White) 2 1 200628 Wheel Axle 18 1 902006 Extension Arm, White 3 2 226401 Wheel 19 8 203309 Washer, 1 O.D. 4 1 986102 Bottom Pole Section 20 4 203104 Bolt, Hex Flange, 5/16-18 x 2 Long 5 1 202820 Rod, 3/8 O.D. x 4-3/4 Long 21 2 200837 Spacer, Plastic 6 1 202822 Eye Bolt, 3/8-16 x 3-3/4 Long 22 2 201562 U-bolt, Round, 3/8-16 x 2-3/4 Long 7 1 200627 Whee
ページ7に含まれる内容の要旨
SECTION A: ASSEMBLE THE BASE This is what your system will look like when you’ve finished this section: HARDWARE USED IN THIS SECTION TOOLS REQUIRED FOR THIS SECTION (not actual size) Item #5 (1) 9/16” and 1/2” Item #10 (10) Item #6 (1) AND/OR Item #15 (6) Item #9 (1) Item #26 (2) Item #14 (2) 9/16” and 1/2” Item #12 (1) Item #8 (5) Item #19 (8) 7 03/03 P/N 211988B
ページ8に含まれる内容の要旨
1 1. Remove contents from tank 2. Install rod (5) through holes in bottom pole section (4) and eyebolt (6). 4 6 5 4 5 6 8 P/N 211988B 03/03
ページ9に含まれる内容の要旨
3. Install wheel axle (2) through wheel carriage (7) and install wheels (3) onto wheel axle (2) with spacers (26) as shown. Insert pole assembly into tank assembly as shown. Secure bottom pole (4) to tank and wheel bracket as shown, a deep socket is recommended. IMPORTANT! DO NOT OVER TIGHTEN. 7 3 26 4 26 3 2 WARNING! 5 TWO PEOPLE IMPORTANT!: REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS 6 WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. THE SPACER (26) WILL FIT LOOSELY UN
ページ10に含まれる内容の要旨
5. Secure non-secured ends of tank struts (11) to tank as shown. Repeat for opposite side. 11 11 14 1 11 10 10 15 Attach extension arm (18) to pole using 6. U-bolt (22), washers (19), nuts (8), as shown. Install pole cap (24) as shown. WARNING! 24 DO NOT LEAVE ASSEMBLY UNATTENDED WHEN 18 EMPTY; IT MAY TIP OVER. 22 8 19 10 P/N 211988B 03/03
ページ11に含まれる内容の要旨
SECTION B: ASSEMBLE THE BACKBOARD This is what your system will look like when you’ve finished this section: TOOLS REQUIRED FOR THIS SECTION HARDWARE USED IN THIS SECTION 1/2” Item #15 (6) Item #17 (12)* OR Item #20 (4) Item #19 (8) 1/2” Item #29 (4)* 11 03/03 P/N 211988B
ページ12に含まれる内容の要旨
7. Install backboard assembly to the pole assembly as shown. Attach backboard and rim (16) to the extension arm (18) using bolts (20), spacers (21), washers (10, 19) and nuts (15) as shown. Tighten completely. Attach bolt covers (29). WARNING! NOTE: TWO PEOPLE Peel protective film from REQUIRED FOR THIS surface of acrylic PROCEDURE. FAILURE backboard prior to use. TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. 20 19 16 15 10 Do not use washers here on spring retu
ページ13に含まれる内容の要旨
WARNING: Use of this product without proper installation of net Install net clips. 8. clips, or when all net clips are not present could result in bodily harm. Be sure to follow directions carefully. WARNING! USE OF THIS PRODUCT CLIP “ARM” WITHOUT PROPER INSTALLATION OF SMART CLIPS, OR WHEN ALL SMART CLIPS ARE NOT PRESENT COULD RESULT IN BODILY HARM. BE SURE TO FOLLOW DIRECTIONS CLIP “BODY” CAREFULLY. 16 Insert one “arm” of clip into ram as shown. Twist “body” of clip slightly so that second “a
ページ14に含まれる内容の要旨
NET INSTALLATION 16 9. SIDE VIEW 17 23 NETCLIP NET Insert net into bottom of clip as shown. SIDE VIEW Twist net until it snaps into position. Net must be centered through clip. NETCLIP NET 14 P/N 211988B 03/03
ページ15に含まれる内容の要旨
SECTION B: SECURING THE SYSTEM Place assembled unit to desired location. Fill tank with water (30 gallons/114 1. liters) or sand (360 lb./163 kg) and snap tank cap (23) in place. Insert T-strap (27) through slot on back of base as shown. Secure unit to ground by twisting tie down stake (25) into ground and hooking T-strap (27) onto tie down stake (25). CAUTION! ADD TWO GALLONS (7.6 LITERS) OF NON-TOXIC ANTIFREEZE IN SUB-FREEZING CLIMATES. 27 28 WARNING! TWO PEOPLE REQUIRED FOR THIS PROCEDURE
ページ16に含まれる内容の要旨
SECTION C: APPLY HEIGHT AND MOVING LABEL Apply Height and Moving label on pole as shown. 1. WARNING! DO NOT LEAVE ASSEMBLY UNATTENDED WHEN EMPTY; IT MAY TIP OVER. 13 MOVING SYSTEM 13 1. While holding pole, rotate basketball system forward until wheels engage with ground. 2. Move basketball system to desired location. 1 3. Carefully rotate basketball system upright. 2 3 4. Reattach ground restraint and check system for stability. 201261 3/99 16 P/N 211988B 03/03
