ページ1に含まれる内容の要旨
HUFFY HUFFY
SPORTS
Customer Service Center
Annex 89 Larkin Ave.
Essendon Airport
Essendon Airport North
Melbourne, Australia 3041
A Huffy Group
WRITE IN MODEL NUMBER:____________
Portable Basketball System with Elevator
Owners Manual
SAFETY INSTRUCTIONS
FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY
RESULT IN SERIOUS INJURY,
PROPERTY DAMAGE AND WILL VOID WARRANTY.
Owner must ensure that all players know and follow these
rules for safe operation of the unit.
To ensure safety, do not attempt
ページ2に含まれる内容の要旨
IMPORTANT! WRITE DOWN MODEL NUMBER FROM BOX ON PAGE 1 OF THIS OWNERS MANUAL WARNING FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. Owner must ensure that all players know and follow these rules for safe operation of the unit. See instruction manual for proper installation and maintenance. Use caution when performing dunk type activities on this unit. Do not hang from any part of unit, including backboard, support braces, rim or net. Do not slide, cli
ページ3に含まれる内容の要旨
2. Slide strut holder (3) between wheel (2) and 1. Lay base (1) bottom up and set wheel (2) into place. base (1). NOTE: Wheel (1) has spacer snapped in place over axle hole, the spacer should face the strut holder (3). 2 1 3 2 1 Bottom View of Base 3. With wheel and strut holder in place, insert spacer (6) thru notch in base, strut holder (3) and wheel (2). Then push spacer thru hole in base. Install bolt (4) thru washer (5), spacer (6), second washer (5) and nut (7) then tighten. Repeat ST
ページ4に含まれる内容の要旨
Setup base (1) as shown and install strut tubes (8). 4. 5. Line-up hole in strut tube (8) with hole in strut support (3) and install hardware as shown. Repeat for opposite side. 8 IMPORTANT! DO NOT TIGHTEN COMPLETELY AT THIS TIME. 1 8 11 10 9 3 6. Slide collar (12) onto strut tubes. Line up holes in tubes (8) with holes in collar (12). 12 Install bolt (9) thru top of collar (12) with washer (10) 7. and nut (11). Tighten upper and lower strut hardware completely. 9 12 8 8 10 11 Side Vi
ページ5に含まれる内容の要旨
Mark poles with tape as shown. 8. 9. IMPORTANT! Bounce middle pole section onto 13 cm (5”) top pole section until they no longer move toward tape reference mark. Upright assembly. HOLES IN TOP AND BOTTOM POLE SECTIONS MUST ALIGN TO CORRECTLY POSITION ELEVATOR SYSTEM. While checking alignment, add bottom pole section and bounce 13 sections together as tight as possible. 86 cm (34”) Bounce sections together as tight as possible. NOTE: POLE SECTIONS MUST OVERLAP 14 8.9 CM (3-1/2”) MINIMUM.
ページ6に含まれる内容の要旨
14. IMPORTANT! Test fit bolts into holes of brackets (19) and carefully 27 rock them in a circular motion to ream out paint from holes if necessary. 25 19 15. IMPORTANT! Finger tighten nuts 21 and bolts until instructed to fully tighten later. 23 22 Fit spacer (22) into pawl (23) and fit 16. 26 pin of pawl through end hole of release lever (24). 24 20 21 17. IMPORTANT! Bolt (28) must be inserted through tube (29), spacer (30), support bracket (21), board bracket (19), release lever (24),
ページ7に含まれる内容の要旨
Starting with nuts (11) flush against bracket (19), secure goal rim (37) and bracket (19) to backboard. 19. NOTE: Mounting nuts and bolts supplied with goal rim hardware. Fold bracket (19) to line up with holes in backboard and secure. 20. 11 11 IMPORTANT! 11 For spring loaded goal rim assembly, refer to 19 instructions included with goal rim hardware. 11 5 36 Do not use washers (5) here on 37 spring return style goal rim. 35 21. Assemble elevator tubes (29) to backboard bracket. 33 30 29 3
ページ8に含まれる内容の要旨
Install net (38). 22. 38 37 23. Support pole on support table. Attach backboard components under assembly to top pole section (12). NOTE: Two people are recommended for this step, use caution, elevator component under assembly is heavy. Then install pole cap (42). 33 33 29 40 13 42 40 41 29 39 SUPPORT TABLE 28 NOTE: Protecting goal rim with cardboard will prevent scratches. 8 P/N 205343A 7/97
ページ9に含まれる内容の要旨
WARNING 24. Roll completed assembled component to DO NOT LEAVE desired position. Fill base with water COMPONENTS UNDER approx. 106 liters (28 gallons) or sand ASSEMBLY UNATTENDED approx. 102 kg (225 lb.) and snap cap WHEN EMPTY, MAY TIP OVER. 43 (43) in place. Secure component to ground using rope (44) and tie down stake (45). 44 IMPORTANT! Add 7.6 liters (two gallons) of NON-TOXIC ANTIFREEZE 45 in sub-freezing climates. 25. Make final adjustments to level the goal rim. If the 26. Inser
ページ10に含まれる内容の要旨
PARTS LIST Item Qty. Part No. Description Item Qty. Part No. Description 1 1 800826 Base, (Gray) 23 1 800876 Pawl & Pin Component 2 2 202808 Wheel, (Black) 24 1 201126 Release Lever 3 1 202935 Strut Holder - Right, (Black) 25 1 201124 Locknut, Hex Head, 3/8-16 1 202936 Strut Holder - Left, (Black) 26 1 240017 Bolt, Hex Head, 1/4-20 x 2-1/4 Long 1 202924 Strut Holder - Right, (Blue) 27 1 203493 Locknut, Hex Head, 1/4-20 1 202925 Strut Holder - Left, (Blue) 28 5 201640 Bolt, Hex Head, 1/2-13 x 7
ページ11に含まれる内容の要旨
HARDWARE IDENTIFIER Item #18 (2) Item #20 (1) Item #26 (1) Item #17 (1) Item #27 (1) Item #25 (1) Item #28 (5) Item #30 (2) Item #31 (1) Item #33 (6) Item #35 (4) Item #36 (2) Item #39 (1) Item #41 (4) 11 OF 11 11 P/N 205343A 7/97
