ページ1に含まれる内容の要旨
Read all instructions BEFORE assembly and USE of product.
KEEP INSTRUCTIONS FOR FUTURE USE.
Model #7311
Sit N Stand LX Tandem Stroller
with Car Seat Snap N Go Attachment System
Instruction Manual
Convenience through innovation and thoughtful design 01.06
ページ2に含まれる内容の要旨
W ARNI NGS WARNING: Please follow all of these instructions to ensure the safety of your child. Keep these instructions for future reference. WARNING: Failure to follow these instructions could result in serious injury or death. Avoid serious injury from falling or sliding out. Always use the safety belts and insure that the children are properly positioned according to these instructions. WARNING: Never leave children unattended. * The maximum weight that can be carried in the Parent T
ページ3に含まれる内容の要旨
P A R T S Parent Tray F r on t Wheels C hild T r ay C anopy Snap N Go Attachment R ear Whe e l s Foot R es t See Page 8 St r o l l e r ASSE MB L I NG TO ENSURE SAFE OPERATION OF YOUR STROLLER, PLEASE FOLLOW THESE INSTRUCTIONS CAREFULLY. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE ASSEMBLY 1. Remove stroller from box. The front wheels, rear wheels, child tray, and canopy need to be installed prior to use. Fig. 1. 2. To attach the front wheels, unfold stroller as described in the section
ページ4に含まれる内容の要旨
6. To attach the front child tray, push the tray onto the front frame tube, lining up the tray between the protruding rivet and the seat. Push backward on the latch until snapped into place. The protruding rivet on the outside Fig. 5. of the frame tube should be above the tray latch. Check that the tray is securely latched in place. Please see fi gure 5 and 6. 7. To remove front child tray, pull outward on the latches and pull outward R i ve t on the tray. Please see fi gure 7. Pleas
ページ5に含まれる内容の要旨
TO USE JUMP SEAT 1. Have child sit on the jump seat facing backwards. Secure the seat belt, Fig. 11. which is attached to the back of the seat, around the childʼs waist, and buckle to the crotch strap. See fi gure 11. 2. Adjust the seat belt to be snug around the childʼs waist. 3. To release, apply pressure to both sides of the male clip until the clip is released. This process requires a moderate amount of effort so as to prevent an accidental release by your child. 4. Be sure that th
ページ6に含まれる内容の要旨
BRAKES WARNING: Always set brakes when the stroller is not being pushed so that the Fig. 13. stroller will not roll away. Never leave stroller unattended on a hill or incline as the stroller may slide down the hill. 1. To engage brakes, apply light downward pressure to the brake lever Fig. 14. located on each rear wheel. The stroller may require slight forward or rearward movement in order to line up the teeth on the brake with each wheel brake cluster. See fi gure 13. Check that the s
ページ7に含まれる内容の要旨
TO UNFOLD STROLLER TO UNFOLD STROLLER Do Not allow children near stroller while unfolding. 1. Release the folding latch, which is located on the right side. See fi gure 18. 2. Lift up on the stroller handle with both hands until the stroller frame is erect and locked in the open position. The stroller has spring-loaded latches on both sides of the frame. Test that both latches are fully engaged prior to placing your child in the stroller. S T O P IF YOU EXPERIENCE ANY DIFFICULTY IN USIN
ページ8に含まれる内容の要旨
Read all instructions BEFORE assembly and USE of product. KEEP INSTRUCTIONS FOR FUTURE USE. Model #7311 Sit N Stand LX Tandem Stroller with Car Seat Snap N Go Attachment System Instruction Manual 01.06 Convenience through innovation and thoughtful design 8
ページ9に含まれる内容の要旨
Car Seat Chart Snap N Go Attachment The Snap N Go attachment system is easily confi gured to carry most infant car seats in the market. New infant car seats are introduced by various manufacturers from time to time and may not be listed below. If you have an infant car seat not listed below, please call our customer service department at (800) 328-7363 between the hours of 8:30 and 4:00 Monday through Friday for additional information and instructions. The Snap N Go attachment system adapts
ページ10に含まれる内容の要旨
Step 1: Remove the child tray. Insert the Snap N Go bar into the two plastic fi ttings located on the lower frame tube of the stroller. Please see fi gure 1. The bar will lock into place with the metal snap button popping into the hole in the plastic fi tting. Check that the snap button is fully engaging the hole in the plastic fi tting and that the Snap N Go bar is securely attached to both sides of the stroller frame. Please see fi gure 2. Figure 1. WARNING: Avoid serious injury
ページ11に含まれる内容の要旨
® ® Cosco Designer 22 and Designer 35 Please follow the following instructions for proper installation of your infant car seat. ® ® Installation of the Cosco Designer 22 and Designer ® Position “5” 35 Infant Car Seat 1. Place front seat in the reclined position. With one hand grasp the car seat handle (in its upright, carrying position) and gently place the seat, so that the baby faces the rear of the stroller, onto the Snap-N-Go attachment system so that the large groove on the seat bot
ページ12に含まれる内容の要旨
® ® Peg Perego Primo Viaggio Please follow the following instructions for proper installation of your infant car seat. Position “5” ® ® Installation of Peg Perego Primo Viaggio Infant Car Seat 1. Place front seat in the reclined position. With one hand grasp the car seat handle (in its upright, carrying position) and gently place the seat, so that the baby faces the rear of the stroller, onto Snap Bar Position “I” the Snap-N-Go attachment system so that the large groove on the seat bott
ページ13に含まれる内容の要旨
® ® Evenfl o Cozy Carry Please follow the following instructions for proper installation of your infant car seat. Position “5” ® ® Installation of the Evenfl o Cozy Carry Infant Car Seat 1. Place front seat in the reclined position. With one hand grasp the car seat handle (in its upright, carrying position) and gently place the seat, so that the baby faces the rear of the Stroller, onto Snap Bar the Snap-N-Go attachment system so that the large groove on Position “I” the seat bottom, ne
ページ14に含まれる内容の要旨
® ® Evenfl o On My Way Please follow the following instructions for proper installation of your infant car seat. ® ® Installation of the Evenfl o On My Way Infant Car Position “1” Seat 1. Place front seat in the reclined position. With one hand grasp the car seat handle (in its upright, carrying position) and gently place the seat, so that the baby faces the rear of the Stroller, onto the Snap-N-Go attachment system so that the large groove on the seat bottom, nearest the head-end of the
ページ15に含まれる内容の要旨
® ® Evenfl o Embrace Please follow the following instructions for proper installation of your infant car seat. Position “4” ® ® Installation of the Evenfl o Embrace Infant Car Seat 1. Place front seat in the reclined position. With one hand grasp the car seat handle (in its upright, carrying position) and gently place the seat, so that the baby faces the rear of the Stroller, onto the Snap-N-Go attachment system so that the large groove on the seat bottom, nearest the head-end of the seat
ページ16に含まれる内容の要旨
® ® Century Vante Please follow the following instructions for proper installation of your infant car seat. Position “1” ® ® Installation of the Century Vante Infant Car Seat 1. Place front seat in the reclined position. With one hand grasp the car seat handle (in its upright, carrying position) and gently place the seat, so that the baby faces the rear of the Stroller, onto the Snap-N-Go attachment system so that the large groove on the seat bottom, nearest the head-end of the seat, h
ページ17に含まれる内容の要旨
® Graco Snug Ride Please follow the following instructions for proper installation of Position “1” your infant car seat. ® ® Installation of the Graco Snug Ride Infant Car Seat 1. Place front seat in the reclined position. With one hand grasp the car seat handle (in its upright, carrying position) and gently place the seat, so that the baby faces the rear of the Stroller, onto the Snap-N-Go attachment system so that the large groove on Snap Bar the seat bottom, nearest the head-end of t
ページ18に含まれる内容の要旨
Cosco Arriva Please follow the following instructions for proper installation of your infant car seat. Position “1” ® ® Installation of the Cosco Arriva Infant Car Seat 1. Place front seat in the reclined position. With one hand grasp the car seat handle (in its upright, carrying position) and gently place the seat, so that the baby faces the rear of the Stroller, onto the Snap-N-Go attachment system so that the seat bottom rest within the frame. Snap Bar 2. Feed the Car Seat Straps thr
ページ19に含まれる内容の要旨
Baby Trend Latch-Loc, Flex-Loc Please follow the following instructions for proper installation of your infant car seat. ® ® Installation of the Baby Trend Latch-Loc Infant Car BT BAR Seat 1. Remove (unscrew) the Snap Bar from the Snap N Go attachment. 2. With one hand grasp the car seat handle (in its upright, carrying position) and gently place the seat, so that the baby faces the rear of the Stroller, onto the Snap-N-Go attachment system so that the Position “4” large groove on the
