Freshtel Sipuraの取扱説明書

ページ1に含まれる内容の要旨

Sipura SPA-2000
Manual Configuration Instructions





Only settings that deviate from factory defaults are included in this document. If your ATA
was previously connected to a different service, you will need to use the screenshots to verify
that all settings are correct; alternatively, you may reset the ATA to factory defaults
(recommended), as described in section 4.

1. Plug in the ATA

Connect a telephone handset, network, and power to the ATA, and wait briefly while it
di

ページ2に含まれる内容の要旨

4. Configure the ATA via its web interface Bring up the ATA's Web configuration page, as described in section 2 of this document. Click on "Admin Login", then "advanced". Clicking on each of the System, SIP, Regional, Line 1 and (optionally) Line 2 tabs in turn, make the following changes; click on the "Submit All Changes" button when done with each page: System System Configuration Admin Passwd: User Password:

ページ3に含まれる内容の要旨

SIP NAT Support Parameters Handle VIA received: yes Handle VIA rport: yes Insert VIA received: yes Insert VIA rport: yes STUN Enable: yes STUN Server: stun.freshtel.net Regional (Australia only) Call Progress Tones Dial Tone: 400@-19,425@-19;30(*/0/1+2) Busy Tone: 425@-10;10(.4/.4/1) Reorder Tone: 425@-10;10(.2/.2/1) Ring Back Tone: 400@-19,425@-19,450@-19;*(.4/.2/1+2+3,.4/.2/1+2+3,0/2/0)

ページ4に含まれる内容の要旨

Distinctive Ring Patterns Ring 1 Cadence: 60(1.5/3.4) Ring 3 Cadence: 60(1.5/3.4,.4/.2,.4/2,.4/.2,.4/2,.4/.2,.4/2,.4/.2,.4/2,.4/.2,.4/2,.4/.2 ,.4/2,.4/.2,.4/2,.4/.2,.4/2,.4/.2,.4/2,.4/.2,.4/2) (Note: the above must appear all as one line in the ATA config. You should copy and paste this line rather then trying to type it in.) Distinctive Call Waiting Tone Patterns CWT8 Cadence: 30(.2/.2,.2/4.4) Control Timer Values (sec) Hook Flash Timer Min: 0.07

ページ5に含まれる内容の要旨

Regional (all countries) Miscellaneous Time Zone: GMT+10:00 FXS Port Impedance: 600 270+750||150nF 220+820||120nF 220+820||115nF 370+620||310nF

ページ6に含まれる内容の要旨

Line 1 (and 2, if using a different Firefly number on the second line) NAT Mapping Enable: yes NAT Keep Alive Enable: yes NAT Keep Alive Msg: Proxy and Registration Proxy: sip.freshtel.net Make Call Without Reg: yes Ans Call Without Reg: yes Subscriber Information Display Name: User ID: Password:

ページ7に含まれる内容の要旨

Audio Configuration Preferred Codec: G729a NOTE: It is vital that the dial plans are entered correctly – as there is not enough space on a page to show them as one line, you should copy and paste one of the below dial plans to ensure it is correct. Missing a space or getting a character wrong will stop them from working. Dial Plan (Australia only -- user has no local dialing prefix set) (*123|*xxxxxxxx|<000:61000> S0|<112:61112> S0|<106:61106> S0|61000 S0|61112

ページ8に含まれる内容の要旨

Dial Plan (UK only -- user has local dialing prefix set) (*123|*xxxxxxxx|999 S0|112 S0|18000 S0|18001999 S0|0800112999 S0|[2-9]xxxxxxx|[2- 9]xxxxxx|[2-9]xxxxx|[2-9]xxxx|0[1237]xxxxxxxxx|01xxxxxxxx|0[045689]x.|1x.) Dial Plan (US and Canada) Once these changes are made and the "Submit All Changes" button is clicked, your ATA will reboot, and you should be ready to place and receive calls with Freshtel. Dialling: To dial a Firefly number or voicemail, pr