ページ1に含まれる内容の要旨
19.2V 3/8” cordless
drill/driVer
66127
set up and operating instructions
®
distributed exclusively by Harbor Freight t ools .
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
read this material before using this product.
Failure to do so can result in serious injury.
sa Ve tHis manual.
© ®
Copyright 2008 by Harbor Freight Tools . All rights reserved. No portion of this manual or any artwork
contained herein may be reproduced in any shape or f
ページ2に含まれる内容の要旨
notice is used to sa Ve tHis manual address practices Keep this manual for the safety warn- not related to personal injury. ings and precautions, assembly, operat- caution, without ing, inspection, maintenance and cleaning the safety alert procedures. Write the product’s serial symbol, is used to address number in the back of the manual near the practices not related to assembly diagram (or month and year of personal injury. purchase if product has no number). Keep this manual and
ページ3に含まれる内容の要旨
2. personal safety ate standards agency. Unapproved safety equipment may not provide a. stay alert, watch what you are do- adequate protection. Eye protection ing and use common sense when must be ANSI-approved and breath- operating a power tool. do not use ing protection must be NIOSH-ap- a power tool while you are tired proved for the specific hazards in the or under the influence of drugs, work area. alcohol or medication. A moment of inattention while operating power 3. power t
ページ4に含まれる内容の要旨
f. use the power tool and tool bits tool performance is decreasing. in accordance with these instruc- When tool performance begins to tions, taking into account the diminish, stop the tool, recharge the working conditions and the work Battery Pack, and use the fresh Bat- to be performed. Use of the power tery Pack for optimal performance. tool for operations different from 5. service those intended could result in a haz- a. Have your power tool serviced by ardous situation. a qualified re
ページ5に含まれる内容の要旨
10. Some dust created by power sand- 7. The battery charger gets ing, sawing, grinding, drilling, and hot during use. The other construction activities, contains charger’s heat can build chemicals known [to the State of Cali- up to unsafe levels and fornia] to cause cancer, birth defects create a fire hazard if it does not or other reproductive harm. Some receive adequate ventilation, due to examples of these chemicals are: an electrical fault, or if it is used in a • Lead from lea
ページ6に含まれる内容の要旨
vibration may cause temporary or sa Ve tHese permanent physical injury, particularly instructions. to the hands, arms and shoulders. To reduce the risk of vibration-related injury: 1. Anyone using vibrating tools regu- larly or for an extended period should first be examined by a doctor and then have regular medical check- ups to ensure medical problems are not being caused or worsened from use. Pregnant women or people who have impaired blood circulation to the hand, past hand inj
ページ7に含まれる内容の要旨
charging the Battery speciFications 1. The Battery Pack (15) must be Charger Input 120V, 60 Hz, charged for three to five hours before 19.2 VDC NiCd Power Output use. Do not charge the Battery Pack Battery, 1.7 aH longer than five hours; the Battery 0 - 600 RPM Drill Speed Pack and/or Charger (21) may be Forward/Reverse damaged. Do not leave the Charger Chuck Type 3/8” Keyless unattended while charging. Charge 15 Standard Setting Torque Settings the Battery on a inflammable surface.
ページ8に含まれる内容の要旨
6. Once the Battery is charged, discon- 3. There must not be hazardous ob- nect the Charger from the electrical jects, such as utility lines or foreign outlet and the Charger from the Bat- objects, nearby that will present a tery Pack. Connect the Battery to the hazard while working. base of the Drill. 4. Warning, to prevent serious injury; verify that the surface has no installing a drill Bit hidden utility lines before drilling or driving screws. 1. Turn the Chuck (4) of the Drill coun
ページ9に含まれる内容の要旨
9. To determine the battery charge level, hold down the Battery Charge Indi- cator. There are three lights (red, yellow, green), if all three are lit the battery is fully charged. If only the red and yellow lights are illuminated, the battery is partially charged. If only the red light is illuminated, then the battery will need to be charged soon. level Battery charge indicator 10. When the hole is drilled, remove the drill bit from the hole while the Drill is still running. This
ページ10に含まれる内容の要旨
be replaced only by a qualified maintenance and service technician. ser Vicing please read tHe FolloWing Procedures not specifically explained in this manual careFull Y must be performed only by a THe MANUFACTUReR AND/OR DISTRIBUTOR qualified technician. HAs ProViDED THE PAr Ts LisT AnD AssEmBL y DiAgrAm in THis mAnuAL As t o preVent A rEfErEnCE TooL onL y. nEiTHEr THE serious injur Y MANUFACTUReR OR DISTRIBUTOR MAKeS From accidental ANY RePReSeNTATION OR WARRANTY OF ANY KIND TO
ページ11に含まれる内容の要旨
parts list parts list part description Qty part description Qty 1 Screw 8 12 Connector 1 2 Right Body 1 13 Trigger 1 3 Chuck Screw 1 14 Battery Clamp 1 4 Chuck 1 15 Battery 1 5 Gear Box & Motor Assembly 1 16 reverse Lever 1 6 Capacitor 1 17 Left Body 1 7 Handle Belt 1 18 Level 1 8 Screw 1 19 Circuit Board 1 9 Washer 1 20 Screw 2 10 VMOS 1 21 Charger 1 11 Cooling Plate 1 22 Case (not shown) 1 assemBl Y diagram record product’s serial number Here: note: If product has no serial number, record mon
ページ12に含まれる内容の要旨
limited 90 da Y WarrantY Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this prod- uct is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installa
