ページ1に含まれる内容の要旨
10.8 VOLT CORDLESS DRiVER
Model 96298
OPERATiNG iNSTRUCTiONS
Due to continuing improvements, actual product may differ slightly from the product described herein.
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at: http://www.harborfreight.com
TO PREVENT SERiOUS iNjUR y, READ
AND UNDERSTAND ALL WARNiNGS AND
iNSTRUCTiONS bEfORE USE.
© ®
Copyright 2007 by Harbor Freight Tools . All rights reserved. No portion of
this manual or any artwork contained herein may be reproduced i
ページ2に含まれる内容の要旨
PRODUCT SPECifiCATiONS Power Source 1.3Ah Battery Charge Time 5-7 Hours, after initial charge Charger Input 120V ~60Hz Chuck Type 1/4” Hex Shank Drive Torque Settings 24 Variable Speed 0-500 RPM Maximum Torque 80 in./lb. Reversible Yes Trigger Lock Yes Weight 1.8 Pounds 1 Hex shank adapter 6 Phillips head bits Included 3 flat head bits 1 Battery Charger Save This Manual You will need this manual for the safety warnings and precautions, assembly, oper- ating, inspection, maintenance and cleaning
ページ3に含まれる内容の要旨
Electrical Safety 1. Avoid body contact with grounded surfaces such as pipes, radiators, ranges, and refrigerators. There is an increased risk of electric shock if your body is grounded. 2. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock. 3. Do not abuse the Charger’s power cord. Never use the Power Cord to carry the Charger or pull the Plug from an outlet. Keep the Power Cord away from heat, oil, sharp edges, or
ページ4に含まれる内容の要旨
4. Remove the battery from the tool and set the Rotation button (6) to the cen- ter, locked position, before making any adjustments, changing accessories, or storing the tool. These preventive safety measures reduce the risk of starting the tool accidentally. 5. Store idle tools out of reach of children and other untrained persons. Tools are dangerous in the hands of untrained users. 6. Maintain the Cordless Driver with care. Keep screwdriver bits clean. Properly maintained accessories w
ページ5に含まれる内容の要旨
“live” wire will make exposed metal parts of the Cordless Driver “live” and shock the operator. 5. Do not use the Cordless Driver or Charger if it has been dropped, damaged, left outdoors, or immersed in liquid. 6. To avoid electric shock, do not pull or carry the Charger by its Power Cord or pull the Power Cord around sharp corners or edges. Do not unplug the Charger by pulling on the Power Cord. Keep the Power Cord away from heated surfaces. 7. To avoid electrical shock, do not handle th
ページ6に含まれる内容の要旨
GROUNDiNG WARNiNG! improperly connecting the grounding wire can result in the risk of electric shock. Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded. Do not modify the power cord plug provided with the tool. Never remove the grounding prong from the plug. Do not use the tool if the power cord or plug is damaged. if damaged, have it repaired by a service facil- ity before use. if the plug will not fit the outlet, have a proper outlet
ページ7に含まれる内容の要旨
2. Double insulated tools may be used in either of the 120 volt outlets shown in the preceding illustration. (See figure b.) ExTENSiON CORDS 1. Grounded tools require a three wire extension cord. Double Insulated tools can use either a two or three wire extension cord. 2. As the distance from the supply outlet increases, you must use a heavier gauge extension cord. Using extension cords with inadequately sized wire causes a seri- ous drop in voltage, resulting in loss of power and possible
ページ8に含まれる内容の要旨
RECOMMENDED MiNiMUM WiRE GAUGE fOR ExTENSiON CORDS* (120 OR 240 VOLT) NAMEPLATE ExTENSiON CORD LENGTH AMPERES (at full load) 25 feet 50 feet 75 feet 100 feet 150 feet 0 – 2.0 18 18 18 18 16 2.1 – 3.4 18 18 18 16 14 3.5 – 5.0 18 18 16 14 12 5.1 – 7.0 18 16 14 12 12 7.1 – 12.0 18 14 12 10 - 12.1 – 16.0 14 12 10 - - 16.1 – 20.0 12 10 - - - * based on limiting the line voltage drop to five volts at 150% of the rated amperes. Chart A SyMbOLOGy Double Insulated Canadian Standards Association Underwrit
ページ9に含まれる内容の要旨
UNPACKiNG When unpacking, check to make sure that the product is complete and undamaged. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible. CHARGiNG (iNiTiAL CHARGE) 1. The Battery Pack (19) requires charging before use. The recommended initial charge time is twelve hours, prior to first use of the Cordless Driver. Note: Always switch to a fresh battery when tool performance begins to diminish. Severe
ページ10に含まれる内容の要旨
OPERATiNG iNSTRUCTiONS NOTE: For additional information regarding the parts listed in the following pages, refer to the Parts List & Assembly Diagram. WARNiNG! Remove the Battery Pack (19) from the tool and set the Rotation Button (6) to its center, locked, position before making any adjustments, changing acces- sories, or storing the tool. Gear box with Torque Ring (2) Chuck (1) Rotation button (6) Trigger (12) battery Pack (19) 1. To install a screwdriver bit, insert the correct Bit (26)
ページ11に含まれる内容の要旨
The different sizes of screws pictured on the Torque Ring are an indication of how much torque the Cordless Driver will apply to the bit before the clutch slips, allowing the bit to stop and helping to prevent damage to the screw, bit, or workpiece. The larger the screw, the more torque is applied before the clutch slips. Always start with a lower torque to help prevent damage. This Cordless Driver also has torque settings between the screw markings to allow a greater range of selection.
ページ12に含まれる内容の要旨
3. After each use: With a soft brush or cloth remove all dirt and debris from the Cord- less Driver. Do not immerse the Cordless Driver in any liquids. 4. When the battery needs to be replaced remember that the lithium battery in this tool must be recycled or disposed of properly. SKU 96298 for technical questions, please call 1-800-444-3353. PAGE 12
ページ13に含まれる内容の要旨
PARTS LiST Part Description Qty Part Description Qty 1 Chuck 1 15 Black Wire 1 2 Gear box with Torque Ring 1 16 Red Wire 1 3 Screw 7 17 Bracket 1 4 Right Body 1 18 Contact Plate 2 5 Screw 4 19 Battery Pack 1 6 Rotation Button 1 20 Ring 1 7 Clear Soft Grip 1 21 Steel Wire Ring 1 8 Right Plate 1 22 Compress Spring 1 9 Tube 1 23 Steel Ball 9 10 Black Wire 1 24 Charger 1 11 Red Wire 1 25 Adapter 1 12 Trigger 1 26 Screwdriver Bits (in rubber 9 sleeve) 13 Left Plate 1 27 Bit Adapter 1 14 Left Body 1
ページ14に含まれる内容の要旨
PLEASE READ THE fOLLOWiNG CAREfULL y THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACE
