ページ1に含まれる内容の要旨
Freestanding cooker
Installation instructions
OR120 double oven models
and User guide
NZ AU
ページ2に含まれる内容の要旨
ページ3に含まれる内容の要旨
1 Contents Safety and warnings 2 Installation instructions 6 Introducing your cooker 20 Using your gas cooktop 21 Cooktop troubleshooting 25 Using your ovens for the first time 26 Oven controls and setting the clock 27 Cooking functions 28 Using the electronic timer 30 Automatic cooking 31 Using your warmer drawer 32 Care and cleaning 33 Warranty and service 47 Important! SAVE THESE INSTRUCTIONS The models shown in this document may not be available in all markets and are s
ページ4に含まれる内容の要旨
2 Safety and warnings Installation WARNING! Electrical Shock Hazard Always disconnect the cooker from the mains electricity supply before carrying out any maintenance operations or repairs. Failure to follow this advice may result in death or electrical shock. WARNING! Cut Hazard Take care - panel edges are sharp. Failure to use caution could result in injury or cuts. Important safety precautions General To avoid hazard, follow these instructions carefully before installing or using this p
ページ5に含まれる内容の要旨
3 Safety and warnings A suitable disconnection switch must be incorporated in the permanent wiring, mounted and positioned to comply with the local wiring rules and regulations. The switch must be of an approved type installed in the fixed wiring and provide a 3 mm air gap contact separation in all poles in accordance with the local wiring rules. In Australia and New Zealand, a switch of the approved type with a 3 mm air gap must be installed in the active (phase) conductor of the fixed wi
ページ6に含まれる内容の要旨
4 Safety and warnings Operation Your freestanding cooker has been carefully designed to operate safely during normal cooking procedures. Please keep the following guidelines in mind when you are using it: WARNING! Explosion Hazard Do not store flammable materials such as gasoline near the cooktop. Do not store flammable material in the ovens or in the drawers. Do not spray aerosols near the cooktop during use. Failure to follow this advice may result in death or serious injury. WARNING!
ページ7に含まれる内容の要旨
5 Safety and warnings Important safety precautions Isolating switch: make sure this cooker is connected to a circuit which incorporates an isolating switch providing full disconnection from the power supply. Household appliances are not intended to be played with by children. Children, or persons with a disability which limits their ability to use the appliance, should have a responsible person to instruct them in its use. The instructor should be satisfied that they can use the applia
ページ8に含まれる内容の要旨
600 mm 6 Installation instructions Product dimensions Fig. 1 Product dimensions Fixing the backguard Position the backguard as shown in Fig. 2 and fix it by screwing the five screws “A”. Important! Installing the backguard is MANDATORY. A Fig. 2 Fixing the backguard 1195 mm MAX 927 mm 120 mm MIN 915 mm
ページ9に含まれる内容の要旨
7 Installation instructions Clearances Installation clearances and protection of combustible surfaces shall comply with the current local regulations eg. AG 601 (AS5601/NZS5261) Gas Installations code. Installation shall comply with the dimensions in Fig. 3, bearing in mind the following requirements: Overhead Clearances In no case shall the clearance above the highest part of the cooker be less than 650 mm or, for an overhead exhaust fan, 750 mm. AII other downward-facing combustible surfac
ページ10に含まれる内容の要旨
8 Installation instructions Levelling the cooker Important! Using the supplied adjustable feet is MANDATORY. For safety reasons and to ensure adequate ventilation, the cooker chassis MUST NOT sit directly on the floor, a plinth, or other support surface. The cooker is already fitted with six levelling feet. Level the cooker by screwing or unscrewing the feet (Fig. 4d). Make sure you follow the instructions in Figs. 4a, 4b, and 4c. Note: nuts are supplied with the cooker Fig
ページ11に含まれる内容の要旨
= = 9 Installation instructions Dotted line showing the position Fitting the anti-tilt bracket of the cooker when installed Important! To restrain the appliance and prevent it tipping accidentally, the anti- tilt bracket and restraining plate supplied must be fitted according to the instructions below. 1 Drill four 8mm diameter holes for Anti-tilt bracket the fixing screws (two in the wall Rear central and two in the floor-see Fig.5) and foot of cooker Fig. 5 Attaching the anti-tilt brack
ページ12に含まれる内容の要旨
10 Installation instructions Moving the cooker Important! To prevent damaging the adjustable feet, ensure the cooker is always lifted by two people. Do not lift the cooker by the door handles. DO NOT DRAG the cooker. Lift the feet clear of the floor. Fig. 9a Correctly lifting the cooker Fig. 9b Incorrectly lifting the cooker Fig. 9c Incorrectly lifting the cooker
ページ13に含まれる内容の要旨
11 Installation instructions Locating the area for gas and electrical connection Dotted line showing the position of the cooker when installed Area for GAS and ELECTRCIAL connection Length (mm) Dimension ~ ~ Fig. 10 Locating the area for gas and electrical connection
ページ14に含まれる内容の要旨
12 Installation instructions Connecting the cooker to the gas supply The gas connection must be carried out by an authorised person according to the relevant standards. Before connecting the appliance to the gas main, mount the brass conical adaptor onto the gas inlet extension pipe, upon which Back the washer has been placed (see Fig. 12 panel following). Conical adaptor and washer are supplied with Fig. 11 Gas pipe positioning options the appliance (packed with conversion kit fo
ページ15に含まれる内容の要旨
13 Installation instructions Installation with a flexible hose assembly If this appliance has to be installed with a hose assembly, the installer shall refer to the network operator or gas supplier for confirmation of the gas type, if in doubt. When used with a flexible hose, the connector on the wall should be between 450 mm to 500 mm from the floor and 200 mm to 300 mm from the left-hand side of the appliance as viewed from the front. The hose connection on the appliance shall face down
ページ16に含まれる内容の要旨
14 Installation instructions Converting to a different gas type This appliance is suitable for use with Natural gas or LPG (check the “gas type” sticker attached to the appliance). To convert from one gas type to another, you need to replace the injectors, and then adjust the minimum burning setting. See instructions on pages following. Important! If you are converting the cooker from Natural gas to LPG, remove the gas pressure regulator before connecting the cooker to the gas supply and r
ページ17に含まれる内容の要旨
15 Installation instructions Replacing the injectors Semi-rapid burner Injector If the injectors are not supplied, contact your nearest Fisher & Paykel Authorised Service Centre. To replace the injectors: 1 Remove the trivets and burners from the cooktop. 2 Using a spanner, remove the injectors (Figs.14a,14b,14c) and replace them with the ones according to the gas type (see the ‘Table for the choice of injectors’). Fig. 14a 3 Fix the warning label (supplied with the Triple ring wok conver
ページ18に含まれる内容の要旨
16 Installation instructions Adjusting the minimum burner setting Check whether the flame spreads to all burner ports when the burner is lit with the gas valve set to the minimum position. If some ports do not light, increase the minimum gas rate setting. Check whether the burner remains lit even when the gas valve is turned quickly from regulationscrew the maximum to the minimum position. If the burner does not remain lit, increase the minimum gas rate setting. To adjust the min
ページ19に含まれる内容の要旨
17 Installation instructions Table for the choice of injectors Natural gas LPG Test Point Pressure 1.0 2.75 [kPa] Gas Gas Injector Orifice Injector Orifice BURNER Consumption Consumption Dia. (mm) Dia. (mm) [MJ/h] [MJ/h] Semi-rapid 1.12 6.30 0.70 6.30 Triple-ring wok 1.60 12.70 0.95 11.90 inner crown 0.85 (no.1 central) 3.60 (*) 0.50 (no.1 central) 3.20 (*) Dual outer crowns 1.15 (no.2 outer) 16.00 (#) 0.62 (no.2 outer) 13.00 (#) (*): Power calculated with inner crown operating. (#): Power
ページ20に含まれる内容の要旨
18 Installation instructions Connecting the power supply cable B To connect the power supply cable to the cooker: 1 Remove the four screws that hold shield “A” C behind the cooker. 2 Open the cable clamp “D” completely. 3 Check the position of the U bolts on the terminal block “B” (Fig. 16a) corresponds to the connection diagrams in Fig. 16b and A D Fig. 16c. 4 Insert the power supply cable into the cable clamp “D” and into the cable protector “C”. The supply cable must be of a suitable
