ページ1に含まれる内容の要旨
Model:
Installers Guide
Escape-36DV
Underwriters
Laboratories Listed
READ THIS MANUAL BEFORE INSTALLING OR
OPERATING THIS APPLIANCE. THIS INSTALLERS
WARNING: IF THE INFORMATION
GUIDE MUST BE LEFT WITH APPLIANCE FOR
FUTURE REFERENCE.
IN THESE INSTRUCTIONS IS NOT
FOLLOWED EXACTLY, A FIRE OR
EXPLOSION MAY RESULT CAUS-
WARNING: IMPROPER INSTALLA-
ING PROPERTY DAMAGE, PER-
TION, ADJUSTMENT, ALTERATION,
SONAL INJURY, OR DEATH. SERVICE OR MAINTENANCE CAN
CAUSE INJURY OR PROPERTY DAM-
- Do not store or
ページ2に含まれる内容の要旨
SAFETY AND WARNING INFORMATION These units MUST use one of the vent systems READ and UNDERSTAND all instructions carefully ! ! described in the Installing the Fireplace section of before starting the installation. FAILURE TO the Installers Guide. NO OTHER vent systems or FOLLOW these installation instructions may result components MAY BE USED. in a possible fire hazard and will void the warranty. This gas fireplace and vent assembly MUST be Prior to the first firing of the fireplace, READ the !
ページ3に含まれる内容の要旨
TABLE OF CONTENTS Safety and Warning Information ................................................. 2 u Service Parts Lists ...................................................................... 4 Section 1: Approvals and Codes................................................ 6 Appliance Certification .................................................................... 6 Installation Codes ........................................................................... 6 High Altitude Installations ...
ページ4に含まれる内容の要旨
Service Parts ESCAPE-36DV (NG, LP) Exploded Parts Diagram Beginning Manufacturing Date: 9-03 (GN, PL) Vue éclatée des pièces Ending Manufacturing Date: ______ 21 27 20 13 14 22 19 16 18 17 15 11 10 VELCRO 9 23 24 25 12 Log set assembly 26 3 5 2 4 7 6 8 Part number list on following page. * La liste des numéros de pièce se * trouve à la page suivante. 1 1 4
ページ5に含まれる内容の要旨
Service Parts List / Liste des pièces de rechange ESCAPE-36DV IMPORTANT: THIS IS DATED INFORMATION. The most current information is located on your dealers VIP site. When order- ing, supply serial and model numbers to ensure correct service parts. / IMPORTANT : L'information fournie dans cette brochure n'est valide que pendant une courte période. Les sites VIP des distributeurs disposent des renseignements les plus récents. Lors d'une commande, veuillez fournir les numéros de série et de modè
ページ6に含まれる内容の要旨
Approvals and Codes 1 Appliance Certification High Altitude Installations The Heat-N-Glo fireplace model discussed in this Installers U.L. Listed gas appliances are tested and approved with- Guide has been tested to certification standards and listed out requiring changes for elevations from 0 to 2,000 feet in by the applicable laboratories. the U. S. A. and in Canada. When installing this appliance at an elevation above 2,000 Certification feet, it may be necessary to decrease the input rating
ページ7に含まれる内容の要旨
Getting Started 2 The Heat-N-Glo Warranty will be voided by, and Heat-N-Glo Introducing the Heat-N-Glo Gas Fireplaces disclaims any responsibility for, the following actions: Heat-N-Glo direct vent gas fireplaces are designed to oper- • Installation of any damaged fireplace or vent system ate with all combustion air siphoned from outside of the component. building and all exhaust gases expelled to the outside. • Modification of the fireplace or direct vent system. The information contained in th
ページ8に含まれる内容の要旨
Ø8” 25-3/8” (203mm) (646mm) 20-7/8” 3-1/2” (532mm) (90mm) 12” (304mm) 1/2” (13mm) 1” 50-7/8” (25mm) (1292mm) GAS LINE 54-1/8” ACCESS (1375mm) 34-1/2” 35-1/2” 31” (876mm) (788mm) (900mm) 2-5/8” (66mm) 11-5/8” (295mm) 36” 4-1/4” (914mm) ELECTRICAL ACCESS (106mm) TOP VENT COLLARS RATNG PLATES AND LABELS GAS GAS LINE ACCESS CONTROLS Figure 1. Diagram of the ESCAPE-36DV 8
ページ9に含まれる内容の要旨
1” MIN. (25.4mm) B Installing the Fireplace A 3 Constructing the Fireplace Chase A chase is a vertical box-like structure built to enclose the gas fireplace and/or its vent system. Vertical vents that run E D on the outside of a building may be, but are not required to be, installed inside a chase. C CAUTION: TREATMENT OF FIRESTOP SPACERS AND CONSTRUCTION OF THE CHASE MAY VARY WITH THE 1/2” MIN. (13mm) TYPE OF BUILDING. THESE INSTRUCTIONS ARE NOT A B C D E SUBSTITUTES FOR THE REQUIREMENTS OF LOC
ページ10に含まれる内容の要旨
Step 2. Framing the Fireplace Fireplace framing can be built before or after the fireplace is CAUTION: MEASURE FIREPLACE DIMENSIONS AND set in place. Framing should be positioned to accommo- VERIFY FRAMING METHODS AND WALL COVERING date wall coverings and fireplace facing material. The dia- DETAILS BEFORE FRAMING. gram below shows framing reference dimensions. Shows center of 10” x 12” vent framing holes for top and rear venting. The center of the hole is one (1) inch (25.4mm) above the center
ページ11に含まれる内容の要旨
DVP90ST 4 6 12 DVP4 DVP6 DVP12 14-1/4 12-3/16 2 MAX. MIN. 24 36 DVP12A 48 9-7/8 DVP24 O 45.0 10-1/4 DVP45 DVP36 11-1/4 7-1/4 1-1/4 TYP DVP48 8-9/16 1/2 TYP 12-9/16 NOTE: PIPES OVERLAP 1-1/4 INCHES AT EACH JOINT. Figure 6. DVP-Series Direct Vent Component Specifications (5-inch inner pipe / 8-inch outer pipe) 11
ページ12に含まれる内容の要旨
Step 3. Installing the Vent System A. Vent System Approvals Identifying Vent Components These models are approved to use DVP-series direct vent The vent systems installed on this gas fireplace may in- pipe components and terminations (see Figures 6 and 7). clude one, two, or three 90° elbow assemblies. The rela- Approved vent system components are labeled for identifi- tionships of vertical rise to horizontal run in vent configura- cation. This pipe is tested and listed as an approved com- t
ページ13に含まれる内容の要旨
CAP STRAIGHT UP VERTICAL VENTING FLUE RESTRICTOR V (FT.) FLUE RESTRICTOR 40' MAX. (12.4 M) V NOTE: On vertical venting configurations install the vertical baffle found in your manual bag per the flue restrictor instructions in this section. Figure 9 2. The restrictor sits inside the 5” diameter collar in the bead area. Using a needle-nose pliers, insert the tips of the pliers into the two holes in the restric- tor plate. Squeeze the pliers to flex the plate. The edges of the plate will need to o
ページ14に含まれる内容の要旨
VENTING WITH ONE (1) 90° ELBOW V (FT.) H (FT.) 1.5' MIN. (.457m) 2.5' MAX. (.762m) 2' MIN. (.609m) 3' MAX. (.912m) 2.5' MIN. (.762m) 6' MAX. (1.82m) 3.5' MIN. (1.06m) 9' MAX. (2.73m) 4.5' MIN. (1.37m) 12' MAX. (3.64m) 5.5' MIN. (1.67m) 15' MAX. (4.55m) 6.5' MIN. (1.98m) 18' MAX. (5.46m) 7.5' MIN. (2.28m) 21' MAX. (6.37m) H 8.5' MIN. (2.59m) 24' MAX. (7.28m) V = 40’ MAX. (12.2m) V+H = 64’ MAX. (19.5m) H = 24' MAX. (7.28m) V H V NOTE: Must have a 12” minimum vertical vent
ページ15に含まれる内容の要旨
VENTING WITH THREE (3) 90° ELBOWS V (FT.) H (FT.) 1.5' MIN. (.457m) 2.5' MAX. (.762m) 2' MIN. (.609m) 3' MAX. (.912m) 2.5' MIN. (.762m) 6' MAX. (1.82m) 3.5' MIN. (1.06m) 9' MAX. (2.73m) 4.5' MIN. (1.37m) 12' MAX. (3.64m) NOTE: H + H = 24' MAX. (7.28m) 1 V + V + H + H = 64' MAX. (19.5m) 1 1 H 1 V 1 V H NOTE: Must have a 12” minimum vertical vent o before attaching a 90 elbow to the unit. V 1 H 1 V H V (FT.) H + H (FT.) 1 1.5' MIN. (.457m) 2.5' MAX. (.762m
ページ16に含まれる内容の要旨
B. Installing Vent Components NOTE: There must be NO INSULATION or other Venting Out the Top Vent combustibles inside the framed firestop opening. The glass must be taken off again for positioning the logs when the unit is finally installed in place and finished around it. Re-install the glass door. Attach vent system to the top 10" starting collars. INTERIOR 1. Attach the First Vent Component to the WALL SHIELD Starting Collars To attach the first vent component to the starting collars
ページ17に含まれる内容の要旨
If the area above the ceiling IS an attic, position and secure For Vertical Runs - One ceiling firestop is REQUIRED at the firestop on top of the previously framed hole. the hole in each ceiling through which the vent passes. To install firestops for vertical runs that pass through ceilings: NOTE: Keep insulation away from the vent pipe at least 1 inch (25mm). • Position a plumb bob directly over the center of the verti- cal vent component. • Mark the ceiling to establish the centerpoint of the
ページ18に含まれる内容の要旨
O N P G R v A H D Q (See Note 2) E v V B L U.S. B T v (3 FT) v B B v S S Electrical V V Service F v v M I D* v X A J or K V X = VENT TERMINAL = AIR SUPPLY INLET = AREA WHERE TERMINAL IS NOT PERMITTED V A = 12" .......................... clearances above grade, veran- K = 3 ft. (U.S.A.) (See Note 1) da, porch, deck or balcony 6 ft. (Canada) .......... clearance to a mechanical air supply inlet B = 12" .......................... clearances to window or door that may be opened, or to per- L** = 7
ページ19に含まれる内容の要旨
WARNING: MAJOR U.S. BUILDING CODES HORIZONTAL ! OVERHANG SPECIFY MINIMUM CHIMNEY AND/OR VENT HEIGHT ABOVE THE ROOF TOP. THESE MIN- IMUM HEIGHTS ARE NECESSARY IN THE INTER- 2 FT. 20 INCH MIN. VERTICAL MIN. EST OF SAFETY. SEE THE PREVIOUS DIAGRAM WALL FOR MINIMUM HEIGHTS, PROVIDED THE TERMI- LOWEST DISCHARGE NATION CAP IS AT LEAST 20 INCHES FROM A VER- OPENING TERMINATION TICAL WALL AND 2-FEET BELOW A HORIZONTAL CAP OVERHANG. X 12 NOTE: This also pertains to vertical vent systems in- stalled on
ページ20に含まれる内容の要旨
Step 5. Installing the Optional Heat-Zone Kit Step 6 The Gas Control System WARNING: THIS UNIT IS NOT FOR USE WITH ! SOLID FUEL. HEAT-ZONE KNOCKOUTS The type of gas control system used with this model is Intermittent Pilot Ignition. Intermittent Pilot Ignition System This system includes millivolt control valve, standing pilot, thermopile/thermocouple flame sensor, and piezo ignitor. WARNING: 110-120 VAC MUST NEVER BE ! CONNECTED TO A CONTROL VALVE IN A MILLIVOLT SYSTEM. WARNING: CONTINUOUS 11
