ページ1に含まれる内容の要旨
kHz MHz
88
540
CR9923
2 Band Single Alarm
Clock Radio
PM FM
MW
TUNING
CR 9923
2 Band Clock Radio
Please read this manual before use
92
600
ROBERTS
Sound for Generations
ページ2に含まれる内容の要旨
Controls (top) 1 23 4 5 1. Alarm set/off button. 2. Sleep button. 3. Minute button. 4. Hour button. 5. Time set button. 6. Snooze. SLEEP Minute Hour ALARM/OFF TIME SNOOZE 6 1
ページ3に含まれる内容の要旨
kHz MHz 88 540 Controls (front) 6 7 8 6. Alarm indicator. 7. PM indicator. 8. Tuning control. PM FM MW TUNING CR 9923 2 Band Clock Radio If you need any further advice, please call our Technical Helpline on :- 2 020 8758 0338 (Mon-Fri) 92 600
ページ4に含まれる内容の要旨
Controls (left and right side) On Off 9. Function switch. 9 Radio Buzz 10. Dimmer switch. 11. Waveband switch. MW 11 DIMMER 12. Volume control. FM High 10 13. Battery compartment Low VOLUME 12 13 3
ページ5に含まれる内容の要旨
kHz MHz 88 540 Switching on 1. Place your clock radio on a flat surface. Plug the power cord into the ON wall socket and switch on. The clock display will flash 12.00. PM FM MW TUNING CR 9923 2 Band Clock Radio TIME Setting the time 1. Press and hold down the TIME button. Minute Hour 2. Whilst holding down the TIME button press the Hour or Minute buttons to set the time. Release the buttons when the correct time is PM reached. The clock uses a 12 hour display with an PM indicator. Ensure tha
ページ6に含まれる内容の要旨
kHz MHz 88 540 Listening to the Radio On 1.Switch on the radio by sliding the Function switch to the 'On' Off position. Radio Buzz 2.Select the required waveband using the Waveband selector MW switch. FM 3. Tune in to the desired station by rotating the Tuning control. The Wire aerial located on the rear of your clock radio is for FM reception. The wire should be fully extended and positioned for VOLUME On FM optimum reception. MW Off Radio For MW reception there is a built in ferrite aerial.
ページ7に含まれる内容の要旨
Setting alarm time ALARM/OFF Minute Hour 1. Press and hold down the ALARM/OFF button. 2. Whilst holding down the ALARM/OFF button press the Hour or Minute buttons to set the time. Release the buttons when the correct alarm time is reached. The clock uses a 12 hour display with a PM indicator. Ensure that the correct 12 hour cycle is selected. PM Checking the alarm time 1. To check alarm time, press and hold down the ALARM/OFF button the display will show the alarm time. ALARM/OFF PM If you ne
ページ8に含まれる内容の要旨
Setting the alarm to wake to buzzer 1. Set the alarm time as previously described. Set the Function switch to the 'Buzz' position. The Alarm indicator will light. On PM Off The alarm will sound every day at the preset time for 1 hour 59 Radio minutes. To switch off the alarm until the next day press the ALARM/ Buzz OFF button. To turn off the alarm permanently set the Function switch to the 'Off' position. Setting the alarm to wake to radio 1. Set the alarm time as previously described. Se
ページ9に含まれる内容の要旨
Snooze control 1. The radio or buzzer alarm can be silenced for 9 minutes by pressing the SNOOZE button. This sequence can be repeated whilst the SNOOZE alarm is sounding. Sleep timer SLEEP The radio can be set to turn off after a preset time has elapsed. PM 1. Press and hold down the SLEEP button. 2. Whilst holding down the SLEEP button set the sleep time using the Hour and Minute buttons (maximum 1 hour and 59 minutes in 1 minute steps). The radio will switch off after the sleep time has elaps
ページ10に含まれる内容の要旨
Dimmer Switch DIMMER The DIMMER switch located on the left side of your clock radio will allow you to adjust the intensity of the clock display to suit room High brightness. Low Specifications Circuit Features Loudspeaker 8 ohms Power Requirements Mains : AC 230 volts, 50Hz only Output power 250mW Back-up Battery : IEC size 6LR61 (6F22, PP3) Aerial System FM Wire Aerial Frequency Coverage FM 87.5 - 108MHz MW Built-in Ferrite aerial MW 525 - 1610kHz ROBERTS RADIO LIMITED PO BOX 130 MEXBOROUGH S
ページ11に含まれる内容の要旨
General (Earth) E The wire coloured BLUE must be Do not allow this unit to be exposed to water or steam. It is recommended that the FM band be used wherever possible as better results in terms connected to the terminal marked (Live) Brown of quality and freedom from interference will usually be obtained than on 3 amp N or coloured BLACK. The wire coloured BROWN must the MW band. L (Neutral) be connected to the terminal Blue marked L or coloured RED. Mains supply N The CR9923 will operate from
ページ12に含まれる内容の要旨
Guarantee This clock radio is guaranteed for twelve months from the date of delivery to the original owner against failure due to faulty workmanship or component breakdown, subject to the procedure stated below. Should any component or part fail during this guarantee period it will be repaired or replaced free of charge. The guarantee does not cover: 1. Damage resulting from incorrect use. 2. Consequential damage. 3. Product with removed or defaced serial numbers. Procedure: Any claim under this
