ページ1に含まれる内容の要旨
SY-6ZB
Motherboard
Quick Start Guide
C
The SOYO CD Quick BIOS Hardware Introduction
Setup Installation
RECYCLED PAPER 100%
POST CONSUMER
FOR HOME OR OFFICE USE
With FCC Standards FC
Tested To Comply
ページ2に含まれる内容の要旨
SOYO ™ SY-6ZB Motherboard ® ® m m * These specifications are subject to change without notice 2 6ZB QSG Version 1.0 - Edition: March 1999 "http://www.soyo.com.tw". on the Internet. The address is Web Site If you need any further information, please visit our document is subject to change without notice. however, no guarantee is given as to the correctness of the contents. The information in this installing the Motherboard. Information in this guide has been carefully checked for reliability; T
ページ3に含まれる内容の要旨
1 Introduction 1 Congratulations on your purchase of the SY-6ZB Motherboard. This Quick Start Guide describes the steps for installing and setting up your new Motherboard. This guide is designed for all users to provide the basic steps of Motherboard setting and operation. For further information, please refer to SY-6ZB Motherboard User's Guide and Technical Reference online manual included on the CD-ROM packed with your Motherboard. Unpacking * If your board comes with a driver disc and a paper
ページ4に含まれる内容の要旨
SY-6ZB Motherboard Layout e Connector 1 1 1 Flash BIOS ITE8671 r 1 1 1PRT N 15 0 COM 1 FDC 51 2 4 8 USB 3 AGP Slot JP44 WOL 1 Slot ® Header PCI Slot #3 PCI Slot #2 1 TM Intel ® 3 82443 ZX ) 1 1 2 Intel ® 82371 EB ISA Slot #1 r r 1 3V Lithium 1 Battery 3 N IDE 2 IDE 1 t r 1 k 2 T _ o D r D + 1 Key Features ® Ø Supports Intel Pentium III processor (450- and includes Hardware Doctor ™ utility ® 500MHz), Pentium II processor (233- Ø Supports Creative SB-LINK ™ (PC-PCI) TM 450MHz) & Celeron proces
ページ5に含まれる内容の要旨
2 Installation 2 To avoid damage to your Motherboard, follow these simple rules while handling this equipment: l Before handling the Motherboard, ground yourself by grasping an unpainted portion of the system's metal chassis. l Remove the Motherboard from its anti-static packaging. Hold it by the edges and avoid touching its components. l Check the Motherboard for damage. If any chip appears loose, press carefully to seat it firmly in its socket. Follow the directions in this section designed to
ページ6に含まれる内容の要旨
Install the Motherboard Follow the steps below in order to perform the installation of your new SY-6ZB Motherboard. Install the CPU Record the working frequency of your CPU that should be clearly marked on the CPU cover. FSB 66MHz FSB 100MHz To mount the processor that you have purchased separately, follow these instructions. T Note: Installing a heat sink and cooling fan on top of your CPU is necessary for proper heat dissipation. Failing to install these items may result in overheating
ページ7に含まれる内容の要旨
Make Connections to the Motherboard This section tells how to connect internal peripherals and power supply to the Motherboard. Internal peripherals include IDE devices (HDD, CD-ROM), Floppy Disk Drive, Chassis Fan, Front Panel Devices (Turbo LED, Internal Speaker, Reset Button, IDE LED, and KeyLock Switch.), Wake-On-LAN card, VGA card, Sound Card, and other devices. For more details on how to connect internal and external peripherals to your new SY-6ZB Motherboard, please refer to SY-6ZB Mothe
ページ8に含まれる内容の要旨
Configure Memory Your board comes with two DIMM sockets, providing support for up to 256MB of main memory using DIMM modules from 8MB to 128MB. For 66MHz front side bus CPUs use 12ns or faster memory; for 100MHz front side bus CPUs use 8ns (100MHz, PC100 compliant) memory. 1 1 2 1 2 Important: It is of prime importance that you install DIMM modules as outlined in the table above in order to preserve signal integrity on 100MHz front side bus systems. Set SW1 for power up FSB clock and AGP bus c
ページ9に含まれる内容の要旨
Set the CPU Frequency You do not need to set any jumper for the CPU frequency. Instead, CPU setting are changed through the BIOS [CHIPSET FEATURES SETUP]. Please refer to Chapter 3 - Quick BIOS Setup for details on how to set the Slot 1 processor frequency. Enable/Disable Power-On by Keyboard (JP50) You can choose to enable the Power-On by Keyboard function by shorting pin 2-3 on jumper JP50, otherwise, short pin 1-2 to disable this function. 1 1 2 2 3 3 Clear CMOS Data (JP5) Clear the CMOS m
ページ10に含まれる内容の要旨
The SY-6ZB Motherboard provides over-clocking capability. Due to the over-clocking setting your system may fail to boot up or hang during run time. If this occurs, please perform the following steps to recover your system from the abnormal situation: 1. Turn off system power (If you use a ATX power supply, sometimes you have to press the power button for more then 4 seconds to shut down the system) 2. Set the SW1 to short if you use a FSB 66MHz CPU 3. Press and hold down the key while t
ページ11に含まれる内容の要旨
3 Quick BIOS Setup 3 This Motherboard does not use any hardware jumpers to set the CPU frequency. Instead, CPU settings are software configurable with the BIOS [CHIPSET FEATURES SETUP]. After the hardware installation is complete, turn the power switch on, then press the key during the system diagnostic checks to enter the Award BIOS Setup program. The CMOS SETUP UTILITY will display on screen. Then, follow these steps to configure the CPU settings. Select [LOAD SETUP DEFAULT] Select the
ページ12に含まれる内容の要旨
4 The SOYO CD 4 Your SY-6ZB Motherboard comes with a CD-ROM labeled "SOYO CD." The SOYO CD contains the user's manual file for your new Motherboard, the drivers software available for installation, and a database in HTML format with information on SOYO Motherboards and other products. Insert the SOYO CD into the CD-ROM drive The SOYO CD will auto-run, and the SOYO CD Start Up Menu will display as shown below. (SOYO CD Start Up Program Menu) The SOYO CD Start Up Program automatically detects whi
ページ13に含まれる内容の要旨
Please note that if the Start Up program was unable to determine which SOYO Motherboard you own, the manual selection menu will pop up, as shown below. Then select the user's manual file that corresponds to your Motherboard model name and click OK. SOYO CD Manuals Please select your manual In the box below and click OK. 6ZB OK Back (Manual Selection Menu) The user's manual files included on the SOYO CD can be read in PDF (Postscript Document) format. In order to read a PDF file, the appropria
ページ14に含まれる内容の要旨
The following drivers are available for Windows 95 (Driver Installation Menu) The following drivers are available for Windows 98 (Driver Installation Menu) 14 The SOYO CD Quick Start Guide SY-6ZB
ページ15に含まれる内容の要旨
A short description of all available drivers follows: Ø Intel Southbridge Drivers Because Windows 95 does not recognize the Southbridge of the newer Intel chipsets (TX, ZX, ZX etc) this utility has to be run, it will update the necessary Windows files. (Only for Windows 95) Ø SOYO SpeedPro Busmaster Driver for Win 95/98 Without the busmaster drivers the CPU will need to be involved every time data is read from or written to the Harddisk. The busmaster drivers make use of DMA (Direct Memory Acces
ページ16に含まれる内容の要旨
Note: Once you have selected a driver, the system will automatically exit the SOYO CD to begin the driver installation program. When the installation is complete, most drivers require to restart your system before they can become active. However, to display the list of all drivers software available with SOYO Motherboards, click the Display all drivers on the SOYO CD button. Please make sure to install only the drivers adapted to your system, or otherwise this cause system malfunctions. Enter t
ページ17に含まれる内容の要旨
ページ18に含まれる内容の要旨
Soyo Computer Inc., (Taiwan) Tel: 886-2-2290-3300 Fax: 886-2-2298-3322 Web Site: http://www.soyo.com.tw E-mail: info@mail.soyo.com.tw Soyo Tek Inc., (USA) Tel: (408) 452-7696 Fax: (408) 573-7696 Web Site: http://www.soyousa.com E-mail: sales@soyousa.com Soyo Europe B.V., (Holland) Tel: 31-79-3637500 Fax: 31-79-3637575 Web Site: http://www.soyo-europe.com http://www.soyo.nl E-mail: Sales@soyo.nl SAAT Technology GmbH, (Germany) Tel: 49-(0)441-204044 Fax: 49-(0)441-203422 Web Sites:http://www.saat.
