ページ1に含まれる内容の要旨
Type Mode
In Type Mode, the typing scale appears on the display and the blinking
cursor moves along it as you type characters on paper.
Type
The Display
Type Mode is activated by sliding the Mode Selector to Type, if
necessary. The typing scale is illustrated below.
Position Indicator
End of Page Pitch Line Impression Keyboard
Status Line
OFF 10 1 M I 12
Cursor
Status Line — Gives current settings, keyboard status, and cursor
position.
Cursor — A rectangle that shows the location of the print ha
ページ2に含まれる内容の要旨
Auto Return You can program the Memory Typewriter to automatically return at the end of each line. When a space or hyphen is typed in the “warning ! Code ^ zone,” which begins five spaces before the right margin, the carrier + 1 automatically returns to the next line. For lengthy words falling at the end of the line, simply type a hyphen as you normally would and the carrier returns automatically. To activate Auto Return: 1. Press Code + Return (1). Unit beeps, and the Status Line prompts Auto R
ページ3に含まれる内容の要旨
Text Enhancements Code B Bold Print Bold + 1. Press Code + Bold (B). A beep is heard, and the display prompts: Bold Print ON. Type Text 2. Type text. 3. To turn off bold print, press Code + Bold (B). No beep is heard, and the display prompts: Code B Bold + Bold Print OFF. NOTE: If correcting bold text within correction memory with Bold Print OFF, bold text will be corrected, but replacement text will not be bolded unless Bold Print is reactivated. Auto Underscore As you are typing, you can aut
ページ4に含まれる内容の要旨
Manual Underscore Position Print Hammer You can also manually underscore text already typed. Shift 1. Position the print hammer under the first character of the text to be Paper In + underscored. 2. Press Shift + -/_ once to underscore each character. Centering Text Auto Center 1. Press Code + Auto Center (2). The carrier moves to the center of the @ ç Code + 2 margins. A beep is heard, and the display prompts: Auto Center @ and indicates the print hammer position. Type Text 2. Type the text to
ページ5に含まれる内容の要旨
Indented Paragraph To indent paragraphs, set “temporary left margins,” so text is automatically indented after carriage returns The example below shows a paragraph which has been indented five spaces. National Accounting Seminar Marvelous Paper Products will participate in the National Accounting Seminar. We will focus on our new computerized accounting program. Those attending will include one Sales Account Executive from each of our Sales Districts, two System Consultants and two Field Service
ページ6に含まれる内容の要旨
Changing Settings You can change the end of page setting, line spacing, impression control, pitch and number of lines displayed in Type Mode. New settings will replace any existing settings. (See “Page Layout.”) NOTE: If you change pitch, remember to change the printwheel. Corrections The typewriter can automatically correct all characters in a three line correction memory buffer. You can easily correct characters not in the buffer by performing an extra step (see “Off-Line Correction”). Rememb
ページ7に含まれる内容の要旨
® LineEraser Position Print Hammer Using the LineEraser feature, you can easily remove an entire line of text located in correction memory. ® Code WordEraser LineEraser + 1. Position the print hammer on any character in the line. 2. Press Code + LineEraser (WordEraser). No beep is heard. Correction begins immediately from the last character typed on the line up to Type Correction the first character typed on the line. Code Return NOTE: You can press Code + Stop (S) to stop LineEraser. + Erasing
ページ8に含まれる内容の要旨
Auto Half Space Position Print Hammer Use this feature to insert one additional character into a word or delete Half Space one or more character(s) from a word. ¿ % Code + 5 1. Position print hammer to any character in the incorrect word. 2. Press Code + Half Space (5) to activate Auto Half Space. The word is automatically erased. Print hammer locates on the center of the space. Type Correction 3. Type the desired word. (Characters appear on the display.) Use Correct to correct errors on the dis
ページ9に含まれる内容の要旨
Forward Correction Position Print Hammer To correct several characters or word(s) not in the correction memory Correct buffer. Code + 1. Position the print hammer to the first character in the series to be corrected using Code + , Code + , Code + , Code + , (twice) Spacebar, Return, and Back Space. Do not use the platen knob to position the print hammer. Retype All Characters 2. Press Code + Correct twice. Two beeps are heard, and the display or Words to be Deleted prompts: Correct Code Forward
ページ10に含まれる内容の要旨
