ページ1に含まれる内容の要旨
ページ2に含まれる内容の要旨
® Elo IntelliTouch /SecureTouch Touchscreen Guide Revision B P/N 008212M Elo TouchSystems, Inc. 1-800-ELOTOUCH www.elotouch.com
ページ3に含まれる内容の要旨
Copyright © 1989, 1992, 1995, 1996, 2001 Elo TouchSystems Inc. All Rights Reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, including, but not limited to, electronic, magnetic, optical, chemical, manual, or otherwise without prior written permis- sion of Elo TouchSystems. Disclaimer The information in this document is subject to change without notice.
ページ4に含まれる内容の要旨
ii
ページ5に含まれる内容の要旨
CHAP TER 0INTELLITOUCH 10-YEAR WARRANTY Except as otherwise stated herein or in an order acknowledgment delivered to Buyer, Seller warrants to Buyer that the Product shall be free of defects in materials and workmanship. The warranty for IntelliTouch touchscreens is 10 years and for IntelliTouch controllers 5 years. Seller makes no warranty regarding the model life of components. Seller’s suppliers may at any time and from time to time make changes in the components delivered as Products or
ページ6に含まれる内容の要旨
THESE REMEDIES SHALL BE THE BUYER’S EXCLUSIVE REMEDIES FOR BREACH OF WARRANTY. EXCEPT FOR THE EXPRESS WARRANTY SET FORTH ABOVE, SELLER GRANTS NO OTHER WARRANTIES, EXPRESS OR IMPLIED BY STATUTE OR OTHERWISE, REGARDING THE PRODUCTS, THEIR FITNESS FOR ANY PURPOSE, THEIR QUALITY, THEIR MERCHANTABILITY, THEIR NONINFRINGEMENT, OR OTHERWISE. NO EMPLOYEE OF SELLER OR ANY OTHER PARTY IS AUTHORIZED TO MAKE ANY WARRANTY FOR THE GOODS OTHER THAN THE WARRANTY SET FORTH HEREIN. SELLER’S LIABILITY UND
ページ7に含まれる内容の要旨
Table of Contents Safety Information . . . . . . . . . . . . . . . . . . . 2-32 IntelliTouch 10-Year Warranty. . . . . . . . . iii Summary of Installation Steps. . . . . . . . . . 2-33 Unpacking the Touchscreen . . . . . . . . . . . 2-33 Chapter 1 Testing the Monitor . . . . . . . . . . . . . . . . 2-33 IntelliTouch Technology . . . . . . . . . . . . 1-1 Disassembling the LCD Monitor . . . . . . . . 2-34 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 Definition of Terms
ページ8に含まれる内容の要旨
Diagnostic LED's . . . . . . . . . . . . . . . . . . . .A-58 IntelliTouch Serial Controllers . . . . . . . .A-58 Diagnostic Codes . . . . . . . . . . . . . . . . . . . .A-59 IntelliTouch Serial Controller (2500S) . .A-59 DB9 and DB25 Connector Pin Positions . .A-60 Appendix B Specifications . . . . . . . . . . . .B-61 IntelliTouch Touchscreens . . . . . . . . . . . . . . . .B-62 IntelliTouch 2500U USB Controller . . . . . . . . .B-64 LED Diagnostic Characteristics . . . . . . .B-68 Agency Approv
ページ9に含まれる内容の要旨
List of Figures IntelliTouch Touchscreen . . . . . . . . . . . . 1-2 IntelliTouch controller . . . . . . . . . . . . . . 1-3 Bezel design . . . . . . . . . . . . . . . . . . 2-7 Bezel edge . . . . . . . . . . . . . . . . . . 2-8 Typical IntelliTouch Touchscreen Installation . 2-10 Proper placement of adhesive tape to the touchscreen. . . . . . . . . . . . . . . . 2-19 Touchscreen Cabling System for Internal Serial
ページ10に含まれる内容の要旨
viii
ページ11に含まれる内容の要旨
List of Tables Serial port controller signals . . . . . . . . . A-54 Pinouts for IC1 Cable and header . . . . . . A-57 The IntelliTouch Serial Controller (2500S) bit position relating to each byte. . . . . . . A-59 USB connector pin numbers and signal names . . . . . . . . . . . . . . . . . . B-66 IntelliTouch touchscreen connector pin numbers and signal descriptions . . . . . . . . . B-67 Power connector, P4 pins and signal descriptions . .
ページ12に含まれる内容の要旨
x
ページ13に含まれる内容の要旨
C H A P TER 1 C HAP TER 1INTELLITOUCH TECHNOLOGY Introduction The IntelliTouch system has three main components: a clear solid glass screen formed to match the shape of a display, a sophisticated electronic controller, and a software driver. The IntelliTouch touchscreen is based on patented surface wave technology. Surface waves are mechanical waves that propagate in the surface of materials such as glass. The touchscreen may be a flat glass panel or a segment of a sphere or cylindrical gla
ページ14に含まれる内容の要旨
The IntelliTouch Touchscreen The IntelliTouch surface wave technology touchscreen consists of a glass panel molded to the shape of a display's face. Each axis of the touchscreen panel has a transmitting and receiving piezoelectric transducer, and sets of reflector stripes. See Figure 2.3 on page 10 for details on the construction of an IntelliTouch touchscreen. Figure 1.1 IntelliTouch Touchscreen Surface wave energy is generated by the transmitting transducers mounted in the corners of the
ページ15に含まれる内容の要旨
The IntelliTouch Controller The IntelliTouch controller provides the drive signal for the touchscreen, converts the received analog signals into digital touch coordinates, and sends these coordinates to the computer. The controller detects touches by comparing received signals to a reference waveform acquired when the touchscreen is in an untouched condition. The IntelliTouch controller detects dirt, dust particles, scratches and other contaminants on the screen and “learns around” them. It
ページ16に含まれる内容の要旨
Driver Software Elo driver software provides a consistent software interface among all Elo touchscreens and controllers. The driver software scales the absolute coordinates received from the touchscreen controller into translated screen coordinates, using the calibration points obtained with the video alignment program included with the driver software. The driver also performs other operations as directed by the application. Elo provides driver programs for the DOS, Windows 3.1, Windows CE
ページ17に含まれる内容の要旨
C H A P TER 2 C HAP TER 2COMPONENT INSTALLATION This chapter outlines the procedures for installing touchscreen components that will convert your monitor into a touchmonitor. Details are given on mounting the touchscreen, controller, and connecting cables. Safety Information WARNING The touchscreen installation procedure outlined in this chapter may require exposure to high-voltage components and handling of the CRT. This procedure can be dangerous and an accident is potentially lethal. Ther
ページ18に含まれる内容の要旨
Protective Clothing Wear safety glasses, gloves, a rubber apron, and heavy protective clothing for any portion of this procedure that involves handling or working near the CRT. Getting Started There are two types of display technologies, CRT displays and LCD displays. IntelliTouch touchscreens are available for most displays, however each display may pose unique installation issues. If, after reading these instructions, you need further assistance please contact Elo Application Engineering f
ページ19に含まれる内容の要旨
To prevent touchscreen breakage, there should be a compliant gasket between the back of the touchscreen and the front of the display to allow for variation in the surfaces when assembling. A gap is also required between the touchscreen and the face of an LCD display to prevent damage to the display. Unlike CRT's, plasma, EL, and backlit LCD displays may be a significant source of heat. The situation may be more significant if the unit is sealed. Any installation must avoid heat rise tha
ページ20に含まれる内容の要旨
Bevel edge for nice appearance Round corners for nice appearance and easy cleaning On bezel and cabinet, choose paint finish and/or surface texture so fingerprints do not show Figure 2.2 Bezel edge It may be necessary to cut ribs and struts inside the bezel. Cutting these ribs and struts does not usually cause difficulties, although the stiffness of the bezel may be reduced slightly. Try not to cut into the posts for the CRT attachment screws. Bezel and tube combinations that require this cut
