ページ1に含まれる内容の要旨
7" Wide LCD Monitor
With 4 Mounting Options
PLHR71
AURM-10B
PLVHR72
INSTRUCTION MANUAL
www.pyleaudio.com
ページ2に含まれる内容の要旨
Table of Contents About the liquid crystal display (LCD) panel 2 Troubleshooting guide 3 Precautions 3 Control & Layout for monitor / wireless remote 4 Accessories 5 Connection diagram 6 Replacing the remote control battery 6 Installing headrest with shroud 7-8 Installing sun-visor with shroud 9-10 installing of headrest case 11 Function setting 12-22 Specifications 23 1
ページ3に含まれる内容の要旨
About the liquid crystal display (LCD) panel 1. Do not press on the LCD panel on the monitor unit as doing so can distort the picture or cause a malfunction, the picture may become unclear, or the LCD panel may be damaged. 2. Notes on cleaning -clean the LCD panel with a slightly damp soft cloth. - do not use solvents such benzine, thinner, commercially available cleaners or antistatic spray. o o o o 3. Do not use this unit temperatures under 5 C (41 F) or over 45 C (113 F). 4. If yo
ページ4に含まれる内容の要旨
Precautions Please read this manual completely and carefully prior to attempt to install your new car video equipment. Install correctly, your new equipment will provide you with years of enjoyable and safe usage. Installing this unit requires technical expertise. This unit should be installed by a qualified technician or service personnel. If you try to install this unit by yourself, do it properly, referring to the installation and wiring diagrams in this operating manual. Improper installat
ページ5に含まれる内容の要旨
Control and layout for the monitor Blue screen when Front Audio Output Remote Sensor no video signal Front audio output Remote control IR sensor (headphones) Power On / Off Front A/V Input Turn on/off the monitor Front audio video input Menu Press to display MENU Power Cord with functions and setting (Male) Adjust Increase Adjust Decrease This multipurpose button This multipurpose button serves serves to increase the selected to decrease the selected parameters, such as volume, paramet
ページ6に含まれる内容の要旨
Accessories Universal Stand Headrest & Sun Visor Shroud AURM-10B Remote Control Headrest Case Key-for removing the monitor Extension Min Din Cable from headrest or visor shroud 7" Wide LCD Monitor With 3 Mounting Options PLHR71 AURM-10B PLVHR72 INSTRUCTION MANUAL www. pyl eau dio .co m Instruction Manual 5
ページ7に含まれる内容の要旨
Connection Diagram 1 2 Fuse (2A) Fuse replacement Never use fuse with an amperage rating exceeding the one supplied with the unit as this could damage the unit. When replacing the fuse, be sure to use one that matches the amperage described on the original fuse. If the fuse blows, check the power connection and replace the fuse. If the fuse blows again after replacement, there may be an internal malfunction. In such a case, consult your nearest your’s dealer. White RCA: Mono Audio Input Yellow
ページ8に含まれる内容の要旨
Steps For Installing Headrest with Shroud Setup work Remove the headrest and set it in an uncluttered work area. Pay the appropriate precautions to ensure that it is not damaged during the installation. CAUTION: make sure the screws are not long enough to go through the headrest! If you have any doubts about this type of installation, please consult your local mobile electronics retailer. Cutting and making holes in the headrest will cause electronic damage which is expensive to repair. Measu
ページ9に含まれる内容の要旨
Route the cable through the headrest Run the supplied cable through the opening and out to the bottom of the headrest. If possible, conceal the wires with a shaft covering. Connect the power, ground and video leads to test the MONITOR. Before connecting the monitor, pull the connecting cable through the headrest shroud as shown in diagram. Place the headrest housing into the opening and secure with correct fasteners. Install the headrest shroud Pull the connecting cable through the cent
ページ10に含まれる内容の要旨
Steps For Installing Sun-visor with Shroud Setup work Remove the visor and set it in an uncluttered work area. Pay appropriate precautions to ensure that it is not damaged during the installation. CAUTION: make sure the screws are not long enough to go through the visor! If you have any doubts about this type of installation, please consult your local mobile electronics retailer. Cutting and making holes in the visor will cause electronic damage which is expensive to repair. Measurements Pr
ページ11に含まれる内容の要旨
Route the cable through the visor Run the supplied cable through the opening and out to the bottom of the visor. If possible, conceal the wires using a shaft covering. Connect the power, ground and video leads to test the MONITOR. Before connecting the monitor, pull the connecting cable assembly through the visor housing as shown in diagram. Place sun-visor shroud into the opening and secure it with correct fasteners. Install the sun-visor shroud T TH HIIS S S SIID DE E U UP P Pull the co
ページ12に含まれる内容の要旨
Rear side of headrest Front side of headrest 11
ページ13に含まれる内容の要旨
Function setting Press MENU button (1)from the remote or press manual button (1) from the monitor 2 to call out the function menu, press button (2 or 3) to the desired setting. 1 Video Signal Picture Parameters DDP OSD Setup Others 3 Monitor Remote OSD Press Menu button (1) to enter video signal input selection. AV1 The symbol show current video input. AV2 Return 2 1 MU EXIT ENT. EXIT SEL. 3 Monitor Remote Video Signal Picture Parameters DDP OSD Setup Others OSD Press the butto
ページ14に含まれる内容の要旨
Video Signal Picture Parameters DDP OSD Setup Others OSD Press the button( 2or3) to adjust the symbol to choose “contrast. Press menu button (1) to enter contrast setting. Contrast [Contrast: Narrows or widens the gap between black & white Brightness (darken & brighten)] Hue Saturation 2 Gamma Function Scaling 1 Return MU EXIT ADJ. RET SEL. 3 Monitor Remote Video Signal Picture Parameters DDP OSD Setup Others OSD Press button 2: adjust contrast to brighten level. Press butto
ページ15に含まれる内容の要旨
Video Signal Picture Parameters DDP OSD Setup Others OSD Press button 2: adjust brightness to lighter level. Press button 3: adjust brightness to darken level. Press button 1 to confirm setting. [Brightness adjustable level: 0~100 . Preset: 50] Brightness 50 2 1 MU EXIT SAVE / EXIT - / + 3 Monitor Remote Video Signal Picture Parameters DDP OSD Setup Others OSD Press the button( 2or3) to adjust the symbol to choose “hue”. Press menu button (1) to enter hue setting. Contrast [H
ページ16に含まれる内容の要旨
Video Signal Picture Parameters DDP OSD Setup Others OSD Press the button( 2or3) to adjust the symbol to choose “letter box”. Press menu button (1) setup as letter box. Scaling The symbol show current selection. Full Screen [An image with an aspect ratio of 4:3 (regular picture)] Letter Box Paranoma 2 Return 1 MU EXIT SET. RET SEL. 3 Monitor Remote Video Signal Picture Parameters DDP OSD Setup Others OSD Press the button( 2or3) to adjust the symbol to choose “para
ページ17に含まれる内容の要旨
Video Signal Picture Parameters DDP OSD Setup Others OSD Press the button( 2or3) to adjust the symbol to choose “saturation”. Press menu button (1) to enter saturation setting. Contrast [Makes color appear lighter or darker] Brightness Hue Saturation 2 Gamma Function Scaling 1 Return MU EXIT ADJ. RET SEL. 3 Monitor Remote Video Signal Picture Parameters DDP OSD Setup Others OSD Press button 2: makes colors appear darker. Press button 3: makes colors appear lighter. Press butt
ページ18に含まれる内容の要旨
Video Signal Picture Parameters DDP OSD Setup Others OSD Press button 2: appear 0 standard (preset). Press button 3: select 1(brighten) . Press button 1: to confirm setting. Gamma Function 0 2 1 MU EXIT SAVE / EXIT - / + 3 Monitor Remote Video Signal Picture Parameters DDP OSD Setup Others OSD Press the button( 2or3) to adjust the symbol to desired setting (scaling). Press menu button (1) to enter scaling setting. Contrast [Scaling: adjusts picture size full screen, letter bo
ページ19に含まれる内容の要旨
Video Signal Picture Parameters DDP OSD Setup Others OSD Press the button( 2or3) to adjust the symbol to choose enable. Press menu button (1) setup as clearness picture. Enable The symbol show current selection. Disable Adjust the symbol to RETURN and press Return menu button (1) to exit. [Set enable as smartnous technology support] 2 12 1 MU EXIT ADJ. RET SEL. 3 Monitor Remote Video Signal Picture Parameters DDP OSD Setup Others O OS SD D Press the button( 2or3)
ページ20に含まれる内容の要旨
Video Signal Picture Parameters DDP OSD Setup Others O OS SD D Press the button( 2or3) to adjust the symbol to choose “language”. Press menu button (1) to enter language setting. Language Select [Setting On Screen Display language] OSD Timeout Transparency Information 2 Memory Recall Return 1 MU EXIT SEL. ADJ. RET 3 Monitor Remote Video Signal Picture Parameters DDP OSD Setup Others OSD Press the button( 2or3) to adjust the symbol to desired language (English). Press
