Summary of the content on the page No. 1
TM-2016-8/8CL Progressive Scan Shutter Cameras
Operation Manual
69-0093
Rev. B
Summary of the content on the page No. 2
Page ii
Summary of the content on the page No. 3
R G E N I G G I A A S M S I T S O E D C E Page iii Notice The material contained in this manual consists of information that is proprietary to JAI, Inc., and may only be used by the pur- chasers of the product. JAI, Inc. makes no warranty for the use of its product and assumes no responsibility for any errors which may appear or for damages resulting from the use of the information contained herein. JAI, Inc. reserves the right to make changes without notice. Microsoft, Windows 98, Windows 95,
Summary of the content on the page No. 4
Page iv WARNING Changes or modifications to this unit not expressly approved by the party responsible for FCC compliance could void the user’s authority to operate the equipment. TM-2016-8/8CL Operation Manual JAI, Inc. 625 River Oaks Parkway San Jose, CA 95134 Tel:(408) 383-0300 Tel:(800) 445-5444 Fax:(408) 383-0301 E-mail: imaging@jai.com www.jai.com
Summary of the content on the page No. 5
Page v Table of Contents Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v List of Figures. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii List of Tables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1.1 Product Description . . . . . . . . . . . . . . . . . . .
Summary of the content on the page No. 6
Page vi 3.7.1 Programmable Look-Up Table (LUT) and Knee Control . . . . . . . . . . . . . .22 3.8 Scan Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 3.8.1 Full Progressive Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23 3.8.2 Two-Row Binning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23 3.9 External Sync and Pixel Locking . . . . . . . . . . . . . . . . . . . .
Summary of the content on the page No. 7
Page vii List of Figures FIGURE 1. TM-2016-8 System Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 FIGURE 2. Camera Link System Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 FIGURE 3. Rear Panel View of Digital Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 FIGURE 4. Serial Communication Cable RS-232B-12 . . . . . . . . . . . . . . . . . . . . . . . . . 10 FIGURE 5. Pinout Configuration for Digital Output Cable
Summary of the content on the page No. 8
Page viii List of Figures
Summary of the content on the page No. 9
Page ix List of Tables TABLE 1. 12-Pin Connector (TM-2016-8) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 TABLE 2. 12-Pin Connector (TM-2016-8CL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 TABLE 3. 31-Pin Connector (MP211-031-113-4300) . . . . . . . . . . . . . . . . . . . . . . . . 8 TABLE 4. Connector and Pinout Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 TABLE 5. Shutter Speed Control Dial . . . . . . . . . . . . . . . . .
Summary of the content on the page No. 10
Page x List of Tables
Summary of the content on the page No. 11
May 31, 2007 TM-2016-8 and TM-2016-8CL Progressive Scan Shutter Camera Operation Manual 1 Introduction 1.1 Product Description * The JAI, Inc. TM-2016-8 is a high-resolution, high-speed monochrome progressive scan CCD camera. The interline-transfer type CCD permits full vertical and horizontal resolution of very high speed shutter images and applications. The electronic shutter, which has speeds to 1/8,000 sec., can be reset asynchronously by external pulse control. The frame rate is 8 fps
Summary of the content on the page No. 12
Page 2 TM-2016-8 and TM-2016-8CL Progressive Scan Shutter Camera 1.2 Features • Miniaturized and lightweight The printed circuit boards in the TM-2016-8 have been arranged based on a new design philosophy that creates modular electronics for the camera, giving it flexibility. In addition, the use of miniature solid-state components results in a compact, lightweight camera that is 44mm x 44mm x 64mm in dimensions, and weighs only 136 grams (CL version 141 grams). • Imager The TM-2016-8 uses
Summary of the content on the page No. 13
Page 3 TM-2016-8 and TM-2016-8CL Progressive Scan Shutter Camera The TM-2016-8 captures async reset images and provides single-shot video output with single FDV. This makes it simpler for an ordinary frame grabber to capture the async reset images. • Read Out Inhibit (ROI) When Asynchronous no-delay shutter mode is selected, it activates the ROI function. With the ROI-controllable pulse to 11-pin input, externally controlled readout of the data is available. • Extra VINIT trigger rejection dur
Summary of the content on the page No. 14
4 7 6 5 3 4 3 2 2 1 1 Page 4 TM-2016-8 and TM-2016-8CL Progressive Scan Shutter Camera 1.4 System Configuration FIGURE 1. TM-2016-8 System Configuration Figure 1 below presents a typical system configuration for the TM-2016-8 camera. UP 0 0 DOWN SHUTTER MODE Digital cable DIGITAL 1 9 2 8 10 3 11 12 7 4 5 6 RS-232B-12 cable in POWER VIDEO CS-232E kit BNC cable 12-pin connectors analog frame Computer with grabber frame-grabber board PD-12 (series) power supply OR 12P-02S Power and Ext. Sync
Summary of the content on the page No. 15
Page 5 TM-2016-8 and TM-2016-8CL Progressive Scan Shutter Camera 2 Installation The following instructions are provided to help you to set up your camera quickly and easily. We suggest that you read through these instructions before you unpack and set up your camera system. 2.1 Getting Started 2.1.1 Unpacking Instructions We recommend that you save the original packing cartons for the cameras and accessories in case you need to return or exchange an item. We also recommend that you bench-test
Summary of the content on the page No. 16
Page 6 TM-2016-8 and TM-2016-8CL Progressive Scan Shutter Camera • Make sure the flow of heat from the camera case to the bracket is not blocked by a non-conductive material like plastic. • Make sure the camera has enough open space around it to facilitate the free flow of air. Please contact JAI, Inc. at (800) 445-5444 or send an email to imaging@jai.com if you have any questions. 2.2.2 Connector Pin Configurations 2.2.2 (a) 12-Pin Connector (TM-2016-8) 1 9 2 8 The TM-2016-8 has a 12-pin
Summary of the content on the page No. 17
Page 7 TM-2016-8 and TM-2016-8CL Progressive Scan Shutter Camera 2.2.2 (b) 12-Pin Connector (Camera Link models) The TM-2016-8 Camera Link cameras have a 12-pin Hirose connector for power input and signal I/O. Pin #1 is Ground and pin #2 is +12V DC. The pinout table is shown below. For TM-2016-8 Camera Link model cameras, serial communication camera control is done via the MDR26 Camera Link connector on the rear panel of the camera. TABLE 2. 12-Pin Connector (TM-2016-8CL) Pin Description
Summary of the content on the page No. 18
Page 8 TM-2016-8 and TM-2016-8CL Progressive Scan Shutter Camera 2.2.2 (d) Camera Link Connector (Camera Link only) a TABLE 3. 31-Pin Connector (MP211-031-113-4300) Pin# Description I/O Pin # Description I/O 1 CLK+ Out 17 CLK- Out 2 LDV+ Out 18 LDV- Out 3 FDV+ Out 19 FDV- Out 4 GND 20 VINIT In [INTEG In 5 EXT HD (TTL) In 21 [EXT VD (TTL) [EXT CLK+] In [EXT CLK-] In 6 INTEG In 22 N/C [HD+] In [HD-] In 7N/C 23 GND [Vinit+/(VD+)] In [Vinit-/(VD-)] In 8 D0+ Out 24 D0- Out 9 D1+ Out 25 D1- Out 10
Summary of the content on the page No. 19
Page 9 TM-2016-8 and TM-2016-8CL Progressive Scan Shutter Camera TABLE 4. Connector and Pinout Configurations Camera Link Connector MDR 26-pin Connector 10226-6212VC Pin # Description I/O Pin # Description I/O 1 GND 14 GND (Shield) 2 Tx OUT 0- Out 15 Tx OUT 0+ Out 3 Tx OUT 1- Out 16 Tx OUT 1+ Out 4 Tx OUT 2- Out 17 Tx OUT 2+ Out 5 Tx CLK OUT - Out 18 Tx CLK OUT+ Out 6 Tx OUT 3- Out 19 Tx OUT 3+ Out a 7 SerTC+ In 20 SerTC- In (LVDS or RS-232 8 SerTo FG Out 21 SerToFG+ Out 9 VINIT- In 22 VINIT+ In
Summary of the content on the page No. 20
190±5mm 9 6 75mm±5mm 3 2 4 Page 10 TM-2016-8 and TM-2016-8CL Progressive Scan Shutter Camera 2.2.3 Shutter Speed Control Dial (TM-2016-8 only) Shutter speed can be selected by switching the shutter dial to the appropriate setting (0 through 9). The factory default settings correspond to the shutter 0 speeds as shown in Table 5 below. TABLE 5. Shutter Speed Control Dial Manual Async 0 no shutter no shutter 11/30 1/8,000 21/60 1/4,000 3 1/125 1/2,000 4 1/250 1/1,000 5 1/500 1/500 6 1/1,000 1/250
