Summary of the content on the page No. 1
UltraCam™
User’s Manual
HO98073
www.jascoproducts.com
For technical support call 1-800-654-8483 (Option 4)
Summary of the content on the page No. 2
Table of Contents CAUTIONS -----------------------------------------------------3 SYSTEM REQUIREMENTS--------------------------------4 PACKAGE CONTENTS-------------------------------------4 MAINTENANCE AND STORAGE ------------------------4 GETTING TO KNOW YOUR ULTRACAM™ ----------5 SOFTWARE INSTALLATION -----------------------------6 GETTING STARTED-----------------------------------------7 TAKING PICTURES------------------------------------------8 VIEWING PICTURES -------------------
Summary of the content on the page No. 3
Cautions Read Before Using Your UltraCam™ 1. You must install the camera driver BEFORE connecting the camera to your computer. 2. Be sure to insert the batteries properly according to polarity. When inserting the batteries, make sure the positive (+) and negative (–) ends of the batteries match the markings on the edge of the battery compartment. 3. Do not leave the camera connected to the USB port on your computer if the camera is not going to be used for a long period of time. T
Summary of the content on the page No. 4
System Requirements 1. Microsoft® Windows® 98, ME, 2000, or XP 2. USB Port and CD-ROM drive 3. 266 MHz processor, 350 MHz recommended 4. At least 32 Mb RAM, 64 Mb recommended 5. 100 Mb free hard drive space 6. 16 bit video display or higher 7. Sound card and speakers to use the audio functions. 8. Internet Access to use the camera in web conferencing. Package Contents 1. Camera 2. Mini Tripod 3. Wrist Strap 4. Two “AAA” batteries 5. USB device cable 6. CD with driver and softwar
Summary of the content on the page No. 5
Getting to Know Your UltraCam™ Note: You must install the camera driver BEFORE connecting the camera to your computer. 5
Summary of the content on the page No. 6
Software Installation Please note that you must install the software BEFORE you connect the camera to the USB port of your computer. 1. Insert the included CD into the CD-ROM Drive of your computer. (The CD should auto load). 2. If the CD does not auto load, follow these steps: a) Double click on My Computer b) Double click on the icon of your CD drive (usually D) c) Double click on setup.exe 3. Follow the on screen instructions to complete the installation. 4. The final installat
Summary of the content on the page No. 7
Getting Started 1. Install the software as described in “Software Installation”. The software MUST be installed BEFORE the camera is connected to your computer. 2. Install the batteries in your camera. a. Remove the battery compartment cover as shown in the illustration. b. Insert the two “AAA” batteries that were included with the camera. When inserting the batteries, make sure the positive (+) and negative (–) ends of the batteries match the markings on the edge of the battery comp
Summary of the content on the page No. 8
Taking Pictures 1. Press the Mode button to turn on the camera. 2. Press the mode button twice to get to the flash On/Off screen. (FA) 3. Press the shutter release button to turn on the flash. (The flash is needed for most indoor pictures. No flash is needed for most outdoor pictures). 4. Press the mode button ten times to select the resolution mode. a) The cameras default setting is high resolution (Hr) b) Once the resolution option screen appears in the LCD screen, Lr
Summary of the content on the page No. 9
Viewing Pictures 1. Open the rubber cover on the camera’s mini USB port. 2. Plug the mini USB plug into the mini USB port on the camera and plug the other end of the USB cable into your computer. 3. Double click on the GE UltraCam icon on the desktop of your computer. 4. The UltraCam application will open. In about five seconds, a pop up screen will appear asking if you want to download the pictures. 5. Click on Yes 6. The pictures will automatically download and you will see thumbna
Summary of the content on the page No. 10
Camera Display Panel 26 Number of images available OF Power on or power off FA/Fo Flash strobe ON/OFF AA Adds a voice recording to the previous image Ar Voice recording. This functions as a voice recorder for a maximum of 12 minutes. Ap Auto play. After making a voice recording, the recording can be played back in this mode. Ct Continuous shot. AI Video Recording. Record up to a 60 second video recording in AVI format. St Self timer Dp Delete last image Da Delete last audio rec
Summary of the content on the page No. 11
Using the Optional Features 1. OF a) This will turn the camera off. b) Press the mode button until OF appears in the LCD screen. c) Press the shutter release button. 2. FA / Fo a) This will turn the flash on (FA) and off (Fo). b) Press the mode button until FA or Fo appears in the LCD screen. c) Press the shutter release button. 3. AA a) This allows you to add a recorded a message to the last picture taken. b) Take the picture you want to add an audio recording to. c) Press
Summary of the content on the page No. 12
4. Ar a) This allows you to use your camera as a voice recorder. Maximum recording time is 12 minutes. b) Press the mode button until Ar appears in the LCD screen; then press and hold the shutter release button. c) Begin talking into the microphone. The best distance for voice recording is within 10 cm. d) When finished recording, release the shutter release button. The camera will automatically default out of the audio recording mode. 5. Ap a) This allows you to listen to the s
Summary of the content on the page No. 13
7. AI a) This allows you to take up to 60 second video clips. b) Press the mode button until AI appears in the LCD screen; then press and hold the shutter release button to begin the video. c) When finished video recording, release the shutter release button. Note: The video taken will be an AVI file. 8. St a) This sets the camera timer to automatically take the picture within ten seconds from when the shutter release button was pressed. b) Mount the camera on the tripod c) Poin
Summary of the content on the page No. 14
11. CA a) This will delete all pictures and recorded audio from the camera. b) Press the mode button until CA appears in the LCD screen. c) Press the shutter release button. d) CA will begin to flash. Press the shutter release button again. 12. Lr a) This will switch the camera to Low Resolution Mode. This option is only available when the camera is currently in High Resolution Mode. b) Press the mode button until Lr appears in the LCD screen. c) Press the shutter release button.
Summary of the content on the page No. 15
15. uP a) This will switch the camera to uncompressed mode. This option is only available when the camera is currently in Compressed Mode. b) Press the mode button until uP appears in the LCD screen. c) Press the shutter release button. d) Uncompressed mode allows 26 High Resolution photos or 104 Low Resolution photos to be taken. 16. F5 / F6 a) This will switch the camera between 50 Hz and 60 Hz mode. In the United States use 60 Hz, this is the default setting. b) Press the mode bu
Summary of the content on the page No. 16
PhotoImpression™ Welcome to PhotoImpression™ ArcSoft PhotoImpression™ is an easy-to-use image-editing program specifically designed for general consumers. The program enables you to edit, retouch, enhance or add special effects to digital images with point-and-click simplicity. It also offers a great variety of project templates for creating greeting cards and calendars, plus the functionalities of the popular Arcsoft PhotoPrinter® and Funhouse™ programs. ArcSoft PhotoImpression
Summary of the content on the page No. 17
To Open ArcSoft PhotoImpression™ 1. Double click on the ArcSoft PhotoImpression™ icon on the desktop. 2. You may also go to ArcSoft PhotoImpression™ under Programs in the Start Menu, and click on PhotoImpression™. Using PhotoImpression™ 1. Click on “Camera/Scanner”. See Diagram. 2. Select “GE UltraCam™” from the drop down “Select Source” menu. See Diagram. Step 7 Step 8 Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 3. Picture Download Met
Summary of the content on the page No. 18
Edit Downloaded Pictures 5. After you have downloaded your pictures, you’re ready to edit them. To get started select a picture from the ones you captured. See Diagram. 6. Select “OK”. Your picture will open in the main window. See Diagram. 7. Click on the Edit, Create, Save or Print button on the left. See Diagram. 8. The associated menus are located on the bottom of the screen. Scroll through those to find what you need. See Diagram. Have fun! Note: Captured photos are stored in th
Summary of the content on the page No. 19
VideoImpression™ Welcome to PhotoImpression™ ArcSoft VideoImpression™ is a powerful, easy-to-use video editing and presentation program designed for consumers. ArcSoft VideoImpression™ enables you to edit video clips and still images, and to combine them to create multimedia desktop video presentations for home, business, and the Internet. ArcSoft VideoImpression™ is your ticket to cool home movies and slide shows. If you know how to drag-and-drop with your mouse, you're all se
Summary of the content on the page No. 20
ArcSoft VideoImpression™ - Getting Started 1. Open ArcSoft VideoImpression™ A) Double click on the VideoImpression™ icon on your desktop. B) You may also go to ArcSoft under Programs in the Start Menu, and click on VideoImpression™ 2. Click on the film reel icon to the right of “New”. 3. Click on the video camera icon to the right of “Capture”. 4. You should be viewing live video now. If not click on the eye icon to start viewing live video. 5. When you’re ready to record, click the
