Summary of the content on the page No. 1
CCD B/W CAMERA
BDM5203H
USER MANUAL
Page : 1
Summary of the content on the page No. 2
CONTE CONTENTSbbbbbbbbbbbbbbbb NTS bbbbbbbbbbbbbbbbbbbb - PRECAUTIONS……………………………………… Page 3 - PACKING CONTENTS...…………………………… Page 4 - 1. User Manual…………………………….............……… Page 4 - 2. Camera…………………..................…………………… Page 4 - 3. CS-Mount Adapter……………………………………… Page 4 - 4. Auto Iris Lens Connector……………...……………… Page 4 - FEATURES AND FUNCTIONS………………….… Page 5 - INSTALLATION…………………………………...… Page 6 - 1. Power connection…………………………………….… Page 6 - 2. Video ca
Summary of the content on the page No. 3
PRECAUTIONS PRECAUTIONS 1. Do not attempt to disassemble the camera. There are no user serviceable parts inside. Ask a qualified service person for servicing 2. Handle the camera with care. Do not misshandle the camera. Avoid striking, shaking, etc. Improper handling or storage could damage the camera. 3. Do not expose the camera to rain or moisture, or try to operate it in wet areas. Turn the power off immediately and ask a qualified service person for servicing. Moisture can damage the camera.
Summary of the content on the page No. 4
P PACKING CONTE ACKING CONTEN NT TS S 1. User Manual 2. Camera 3. CS-Mount Adapter 4. Auto Iris Lens Connector Page : 4
Summary of the content on the page No. 5
FEATURES AND FUNCTIONS F - Auto Light Control (ALC) function - Electronic Light Control (ELC) function - Automatic Gain Control (AGC) function - Internal Synchronisation - Minimum Illumination of 0,05 Lux @ F2.0 - Signal to noise ratio > 50 dB (AGC off) - Horizontal resolution of 520 TV lines. - Auto Iris Lens Control selectable between video signal – and DC power controlled. Page : 5
Summary of the content on the page No. 6
INSTALLATION I 1. Power connection Connect the DC 12V powercable with the DC 12V Terminal. DC 12 V ( 10%) Power connector camera rear side Resistance of copper wire (at 20 °C) Copper 0,22 mm² 0,33 mm² 0,52 mm² 0,83 mm² wire size 0,078 0,05 0,03 0,018 / m Calculation of max. cable length between camera and power supply: 10,5V DC V – (R x 0,42 x L) 16V DC L : Cable length (m) R : Resistance of copper wire ( / m) V : DC output voltage of power supply (V DC) L standard = V - 12 /
Summary of the content on the page No. 7
2. Video cable It is recommended to use a monitor with a resolution at least equal to that of the camera. Camera rear side The max. extensible coaxial cable length between camera and the monitor is shown below. Coax cable type RG-59/U RG-6U RG-11/U RG-15/U (3C-2V) (5C-2V) (7C-2V) (10C-2V) Recommended max. cable length (m) 250 500 600 800 Page : 7
Summary of the content on the page No. 8
3. Installation of the Auto Iris Lens Connector Install the lens connector (YFE4191J100) when using a video drive ALC lens. The installation should be made by qualified service personnel or system installers. The pin assignment of the lens connector is as follows: Signal for video iris lens : Signal for DC iris lens : Pin 1: Power Source + 9V DC, Pin 1: DAMP - 50mA max. Pin 2: DAMP + Pin 2: Not used Pin 3: DRV + Pin 3: Video Signal; 1,3Vpp /40k Pin 4: DRV – (GRD) Pin 4: Shield; ground Auto iris
Summary of the content on the page No. 9
4. Mounting the Lens Camera description 1. Set up the lens by turning it clockwise on the lens mount of the camera. In case you are using a CS-Mount Lens connect the CS-Mount Adapter to the lens first and then mount it to the camera body. 2. Connect the lens cable to the Auto Iris Lens Connector on the side of the camera. 3. Adjust the Auto Iris Lens Selection Switch on the back (see page: 7) according to the used lens: To Video (V/D) for video controlled iris lens or DC for DC controlled ir
Summary of the content on the page No. 10
5. Operating controls and functions Function switch on the back (see page: 7) S/W Function ON OFF 1 BLC ON OFF 2 ALC E/S ALC 3 --- --- --- 4 AGC MIN MAX S/W 1 Back Light Compensation Mode Selector (BLC ON, OFF) Lets you select the mode according to the position of the object and light conditions on the screen. S/W 2 Automatic Light Control / Electronic Light Control Selector (ALC; E/S) Lets you select the mode according to the lens type used. ALC: Select this mode when an auto iris lens (ALC len
Summary of the content on the page No. 11
SPECIFICATION S Model Name BDM5203H Signal Standard PAL Objective Mount C-Mount and CS-Mount (adapter) CCD – Chip 1/3” Super HAD CCD Scanning System 2:1 Interlaced Scanning Frequency H: 15.625 kHz V: 50 Hz Total Pixels 795 (H) x 596 (V) app. 470.000 Pixel Effective Pixels 752 (H) x 582 (V) app. 440.000 Pixel Horizontal Resolution 520 Lines Electronic Shutter 1/50 – 1/100000 auto S/N Ratio > 50 dB (AGC off) Sensitivity 0.05 Lux @ F 2.0 Sync System Internal Sync Automatic Iris Contr
Summary of the content on the page No. 12
ADDRESS (Technical specifications subject to change. No liability will be assumed for printing errors or other errors.) Page : 12
