Summary of the content on the page No. 1
User Guide
MC200CM
MC210CS
MC220L
Gigabit Ethernet Media Converter
Summary of the content on the page No. 2
COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright © 2011 TP-LINK TECHNOLOGIES C
Summary of the content on the page No. 3
CONTENTS Package Contents...........................................................................1 1. Introduction.............................................................................1 2. Features...................................................................................2 3. Appearance Indication...........................................................3 3.1 LED Indicators................................................................. 3 3.2 Switch...................
Summary of the content on the page No. 4
Package Contents Before starting using the products, make sure what you have is what you ordered. The Converter includes: One Converter One AC-DC Power Adapter (DC9V/600mA) One User Guide 1. Introduction MC200CM, MC210CS and MC220L are Gigabit Ethernet Media Converters. The FX port of MC220L supports hot-swappable. The converter mediates between a 1000Base-TX segment and a 1000Base-X segment. It is primarily designed for larger bandwidth, and higher speed demanding workgroups th
Summary of the content on the page No. 5
Rear Panel Front Panel MC220L Note: This media convertor can also be powered by 5VDC Adapter. 2. Features Comply with IEEE 802.3ab and IEEE 802.3z. Provide one SC/LC fiber connector and one RJ45 connector. Please check the table in page 3 for the accurate connector of each model. Work at 1000Mbps in Full-Duplex mode for both TX port and FX port. Support auto MDI/MDIX for TX port. Extend fiber d
Summary of the content on the page No. 6
FX port supports hot-swappable(only for MC220L). Connectors and Network Cables Supported The connectors and network cables supported by the converter are listed as follows. Connectors: RJ-45, SC, LC. Network Cables: Cat.5 Twisted-Pair(below abbreviated as TP), 9/125um Single-mode fiber, 62.5/125,50/125um Multi-mode fiber. Output Transmission Transmission Interface Center Distance Media Wavelength Model No. 0.55km(50/125um) Multi-mode MC200CM RJ45--SC 850nm 0.22km(62.5/125um
Summary of the content on the page No. 7
When you take a look at these indicators, you will know what’s happening on your network. PWR RX LINK LINK FX TP Name Status Indication On Power on PWR Off Power off On There’s a valid link for FX Port. FX LINK Off There’s no valid link for FX Port. On There’s a valid link for TP Port. LINK Off There’s no valid link for TP Port. TP On The converter is receiving data from TP port. RX The converter is not receiving data from TP Off port. Note: The TP port mention
Summary of the content on the page No. 8
AUTO: The FX port operates in Auto-Negotiation mode. Note: Be sure the opposite end is using the same setting. When using two converters at the same time, the two converters must be set to FORCE mode. When connected to other products, such as TL- SL2210WEB or TL-SL2428WEB, the converter must be set to Auto- Negotiation mode. We suggest leaving the switches on AUTO. Please reset the converter after configuring the switches. Then the change would take effect. 4. Installation Guides
Summary of the content on the page No. 9
Note: Either two MC200CM or two MC210CS could cooperate. MC220L can be plugged in with two kinds of SFP modules, single-mode or multi-mode. Plug the SFP module into MC220L Transmits and receives data between two MC220L Note: Two MC220L with the same SFP module could cooperate. 6
Summary of the content on the page No. 10
Transmits and receives data between MC220L and MC200CM/MC210CS Note: MC220L could be connected to MC200CM or MC210CS, however, the SFP module in MC220L must use the same mode and the same wavelength as the opposite end. (Please refer to the table below) And the connection fiber must be LC-SC fiber. Model No. MC220L connect with MC200CM MC210CS Transmission 1310nm, SFP module 850nm, Multi-mode Media Single-mode 4.2 Configuration In order to achieve the aim of effectively expanding
Summary of the content on the page No. 11
Note: For the correct connection between 2 Media Converters, please refer to connection diagram in 4.1 ---- two MC200CM, two MC210CS, two MC220L or one MC220L with another MC200CM/MC210CS. 2. Another effective application is to place one converter directly between a 1000Base-TX network and a fiber optic (FX) device. 4.3 Installation Procedure Use a fiber cable to connect two converters, or connect a converter with a 1000Base-FX Device. 1. Connection of a Converter and a 1000Base-
Summary of the content on the page No. 12
2. Connection of two Converters or a Converter and a 1000Base- FX Device: Use a SC fiber cable to connect the two Converters’ SC connectors or the SC connecters of a Converter and a 1000Base-FX Device. 3. Turn on the power. 4.4 Install Media Converter into MC1400 Tweak out the two screws located on either side of the Chassis’s one side, and use them to install the retainer as follows. 1. Turn off the switch power, take off the front guard on the chassis, insert the boxlike Media Con
Summary of the content on the page No. 13
POWER LED lit on. Then you can operate it as the boxlike Media Converter of the MC series. 5. Troubleshooting If you encounter some problems when you install or use this product, please try to solve the problem according to the following steps. If it still doesn’t work, please contact your dealer or ask for help from our technical support. 1. PWR LED is off: The power error. Please check that whether the power lead is connected correctly or not. 2. LINK LED (TP port) is off: Please co
Summary of the content on the page No. 14
6. Appendix: Specifications MC200CM Standards and Protocols IEEE802.3ab, IEEE 802.3z, IEEE 802.3x Media Interface SC, RJ45 Cat.5: 100m Max. Distance Multi-mode Fiber: 0.55km Power External Power Adapter Operation: 0 ℃~40 ℃ Temperature Storage: -40 ℃~70 ℃ Operation: 10%~90% non-condensing Humidity Storage: 5%~90% non-condensing MC210CS Standards and Protocols IEEE802.3ab, IEEE 802.3z, IEEE 802.3x Media Interface SC, RJ45 Cat.5: 100m Max. Distance Single-mode Fiber: 15km Po
Summary of the content on the page No. 15
MC220L Standards and Protocols IEEE802.3ab, IEEE 802.3z, IEEE 802.3x Media Interface LC, RJ45 Cat.5: 100m Max. Distance Multi/Single-mode Fiber: 0.55km/10km Power External Power Adapter Operation: 0 ℃~40 ℃ Temperature Storage: -40 ℃~70 ℃ Operation: 10%~90% non-condensing Humidity Storage: 5%~90% non-condensing 12
Summary of the content on the page No. 16
7106503685
