Demco CHRYSLER SEBRING CONVERTIBLE TP20108 user manual

Summary of the content on the page No. 1

10-07
TP20108, REV.4
ASSEMBLY
Chrysler
OPERATION
Sebring Convertible
REPLACEMENT PARTS
Doing Our Best to Provide You the Best
BOLT TORQUE SPECIFICATIONS
READ complete manual CAREFULLY
BEFORE attempting operation.
STANDARD BOLTS:
METRIC BOLTS:
Size Grade Torque
Size Torque
5/16” 5 20 ft/lbs.
8mm 22 ft/lbs.
Pin Height - 12-1/2” Center - 21”
3/8” 5 35 ft/lbs.
10mm 42 ft/lbs.
7/16” 5 56 ft/lbs.
12mm 70 ft/lbs.
1/2” 5 85 ft/lbs.
14mm 95 ft/lbs.
6
5
1
1
7
3
2 1
2
1
3
8
2
3
1
4
3
2
8
9517108 PARTS

Summary of the content on the page No. 2

WARNING: FAILURE TO FOLLOW THESE INSTRUCTIONS CAN RESULT IN LOSS OF TOWING VEHICLE CONTROL, SEPARATION OF THE TOW BAR FROM THE TOWING VEHICLE, SEPARATION OF THE TOWED VEHICLE FROM THE TOW BAR, CAUS- ING SEVERE PERSONAL INJURY, DEATH, OR PROPERTY DAMAGE. IMPORTANT INSTALLATION ITEMS DEMCO products and accessories are intended to be installed by professional installers with experience, CAUTION proper equipment and the ability to do modifi cation work. Installers with these qualifi cations can

Summary of the content on the page No. 3

5. Remove two nuts holding facia to fender on each side by going through wheel well opening. 2. Remove screws from wheel well to facia on each side. 6. Remove two plastic push fasteners from bottom side 3. Remove plastic wheel well extension, two plastic push of bumper and unplug fog light. fasteners. Remove front portion of driver’s side wheel well, held on by four screws. 7. Pull facia down on each side by fender and carefully pull facia off. 4. On passenger side, loosen front portion o

Summary of the content on the page No. 4

9. Slide base plate up from bottom and line up tight against front frame bracket as shown in picture. Clamp in place. 12. Remove one front sub-frame bolt from each side, for bottom brace (see picture). Install long end of brace and refasten long sub-frame bolt. On other end of brace, use 1/2” x 1-1/4” bolt, 1/2” lock washer, and 1/2” hex nut through brace and base plate. Tighten these bolts. Do this on both sides. 10. Center punch all eight holes (four on each side) and drill 3/8” h

Summary of the content on the page No. 5

Ag ❍ RV ❍ Warranty Registration Rental ❍ Dethmers Manufacturing Company Brakes ❍ 4010 320th Street • Box 189 • Boyden, Iowa 51234 Marine ❍ Toll Free 800-54DEMCO (800-543-3626) • FAX 800-845-6420 www.demco-products.com Very Very Satisfied Satisfied Dissatisfied Dissatisfied How satisfied are you with our product? ❍❍ ❍ ❍ How satisfied are you with the dealership/distributor sales staff? ❍❍ ❍ ❍ Dealer/Distributor Name City State How satisfied are you with the company sales staff? ❍❍ ❍ ❍ How satisf

Summary of the content on the page No. 6

Postage Dethmers Manufacturing Company 4010 320th Street, Box 189 Boyden, Iowa 51234

Summary of the content on the page No. 7

DEMCO PRODUCTS ORIGINAL PURCHASERS LIMITED WARRANTY 1. Extent and Duration of this Warranty: Your Demco product has a Lifetime Limited warranty to be free from defects in materials and In addition, the warranty does not extend to repairs made workmanship under normal use and service from date necessary by normal use of parts, accessories or other of purchase by the original (fi rst) retail owner, or until it is equipment which in the judgment of Warrantor, are either resold or transf

Summary of the content on the page No. 8

DETHMERS MFG. COMPANY 4010 320th St., P.O. BOX 189, BOYDEN, IA. 51234 PH: (712) 725-2311 FAX: (712) 725-2380 or 1-800-845-6420 TOLL FREE: 1-800-54DEMCO (1-800-543-3626) www.demco-products.com